Renesas Renesas SmartBond(tm) have two ADC blocks:
GPADC and SDADC.
This change adds drivers for both.
Each ADC supports only one channel setup, drivers allow
to have multiply channels in sequence. Switching
between ADC sources in done in software.
GPADC has 10 bit resolution (accuracy can be increase
with oversampling). Values up to 3.6V can be measured
on selected pins. V30 and VBAT1 can also be measured.
SDADC has 14 bit resolution and can take measurements
from 8 pins (single of differential) and VBAT.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Glitches were observed if a GPIO pin was configured by
ROM to a non-default state and then Zephyr PINCTRL
reconfigured the pin. The fix involves using the correct
PINCTRL YAML output enable and state flags. Reading the
current spin state and reflecting into new pin configuration
if the pin is output and the drive low/high properties are
not present. We also take advantage of GPIO hardware reflecing
the alternate output value in the parallel output bit before
enabling parallel output mode. Interpret boolean flags with
both enable and disable as do not touch if neither flag is
present. We give precedence to enable over disable if both
flags mistakenly appear. Note, PINCTRL always clears the
GPIO control input pad disable bit.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Update LTDC driver to use LCDIF bindings, to simplify bindings
between LCD interface controller IP blocks.
Boards supporting the LTDC are also updated to use the properties as
declared by the new lcd controller binding
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add common LCD interface binding. This binding captures the
following properties, which are shared between multiple LCD interface
IP blocks:
- VSYNC/HSYNC pulse width
- Vertical/Horizontal front and back porch
- HSYNC,VSYNC,data enable, and pixel clock polarity flags
- pixel clock frequency
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
All Nucleo boards provide the ST Morpho connector/header, which exposes
all pins of the MCU. It is tipically used in ST shields, so provide a
nexus node to allow creating generic shields.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Define some macros that will help to define the STM32 ADC resolutions in
the dtsi files. The end goal is to simplify the driver by removing code
specific to particular series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Added a generic driver for RaspberryPi Pico PIO.
This driver is an intermediate driver for abstracting the PIO
device driver from physical pin configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
Defines the RCC reset registers for the stm32h5cx devices
Note that all stm32h5x do not have all the bus registers.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Defines the clocks for the stm32H5 device.
The PLL is similar to the stm32U5 except for the mul-n from 8 to 420.
The HSI is similar to the stm32h7 with a prediv.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add a GPIO nexus binding for Pmod interface connectors.
This commit also includes a header file with macros
that map signal names in the Pmod specification to
the corresponding indices in the GPIO nexus, meant for
use in devicetree files.
Signed-off-by: Alexander Mihajlovic <alexander@eub.se>
Rewrite MCUX LPADC driver, to better utilize hardware.
the following changes have been applied:
- channel numbers now correspond to hardware channel command slots,
use "input_positive" and "input_negative" fields along with channel
definitions in dt-bindings/adc/mcux-lpadc.h to select a channel
- the number of channel command slots available is configurable via
CONFIG_LPADC_CHANNEL_COUNT
- Side A and side B channels are now supported
- differential channel mode is now supported
- ADC channels now are sampled via hardware, without additional
software triggering
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add initial version of clock control for Atmel SAM SoC series. This add
support to Power Management which allows control peripherals clock.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
All of the following list the registers at 0x8C/0x90:
- RM0431 ('f72x/'f73x)
- RM0385 ('f74x/'f75x)
- RM0410 ('f76x/'f77x)
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Initial commit introducing the input subsystem into Zephyr.
Includes the input_event data structure, the input_report_* APIs, an
iterables sections based subscription API and two operation modes:
synchronous, where the listeners are called directly, and asynchronous,
where the listeners are called in a dedicated thread.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add clock rate definitions for MIPI and LCDIF peripherals, to enable
retrival of these peripheral clock rates at runtime.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Microchip XEC devices specify GPIO pin using octal numbering and
organize pins in banks of 32. Chip documentation does not use
bank naming rather naming each pin by its octal number. This has
led to the developer having to calculate the bit position of a pin
in its 32-bit bank when a specifying the pin for GPIO usage. We
created a set of defines for all possible GPIO pins that specify
the DT GPIO bank name used in the chip level DTSI files and the
bit position in that bank.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Added initial version of Infineon CAT1 Pin controller driver.
Added initial version of binding file for Infineon CAT1 Pinctrl driver.
Added initial version of dt header for Infineon CAT1 pinctrl driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Add PLLI2S R as I2S source clock.
For now I2S_CKIN (fixed clock) is not supported.
This change only consider F401 and compatible PLL I2S implementations.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The original implementation of the GEM's device tree binding
implied that:
1) on the UltraScale+, the MDC clock divider is applied to
the LPD_LSBUS_CLK. According to the most recent documentation,
this is not the case, instead, the MDC divider is applied to
the IOU_SWITCH_CLK.
2) any MDC divider greater than 32 is reserved to the Zynq-7000
(in the driver itself, accessibility of the larger dividers was
also #ifdef'd), as the Zynq's MDC clock source, the cpu_1x
clock, can have significantly higher frequencies than the
UltraScale's LPD_LSBUS clock.
The respective documentation in the device tree binding header
file is hereby fixed.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Change the name of the custom macro defined for the stm32 devices
to fit the VND_PWM_xxx model
Keeping old deprecated macro, though.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Defines DMA macro to help channel configuration and feature for the stm32
devices. Add one default value for most of the usecases
of peripheral DMA settings.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The interrupt is used to wake up EC from low power mode.
So EC does not defer eSPI bus while transaction is accepted.
Fixes EC host commands slow issue.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
While nPM1100 is to be operated in fixed configuration for some
applications, it has some degree of configuration via GPIOs. For
example, mode (auto/PWM) can be configured via MODE pin. VBUS current
can also be adjusted using ISET pin, even though there is no API yet to
limit the PMIC input current.
This patch adds a new regulator class driver for nPM1100 PMIC, so that
it can be used with the standard regulator API when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In some case, we may need to describe a domain clock for a device
while there is no way to configure it (ex: USB clock set on PLL_Q output
on F405 devices > It is not selectable).
Then, configuring a device clock domain in the clock_control driver
will allow to retrieve its subsys rate.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following updates previously done for other drivers, rename all
occurrences of S32 to NXP S32 to avoid ambiguity.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
ESP32 and ESP32-S2 HW clock are tied to DTS clock configuration.
This changes updates the default configuration to retrieve
this information from DTS.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Fix Microchip XEC clock control driver single-ended XTAL2 pin
initialization. Add support for external 32KHZ_IN pin as a
clock source including PINTRL to switch the GPIO to 32KHZ_IN
function. Add device tree option to disable internal silicon
oscillator if it is not required by the configuration. Add
device tree tuning options based on crystal and board layout.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add initial support for gd32l23x series. gd32l23x used Cortex-M23, based
on ARMv8-M baseline, implement the System Timer.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Add config cell property to gd,gd32-dma.
For supporting hardware variation, Splitting base definition
to gd,gd32-dma-base.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add a new dedicated clock control header file for the STM32F7 series.
It is copied from the STM32F4 file with added clock defines and helpers
to select peripheral clock sources that are specific to F7 series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
dt-bindings f7
This commit adds initial support for gecko pinctrl driver
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
PCA9420 PMIC offers of multiple operation states, or DVS (Dynamic
Voltage Scaling). Such states may be automatically changed by hardware
using MODESEL0/1 pins. Certain MCUs allow to automatically configure
certain output pins when entering low power modes so that PMIC state is
changed without software intervention. This means that application just
needs to configure the voltages for each state using
`nxp,modeN-microvolt`, set `nxp,enable-modesel-pins` in devicetree and
forget about configuring regulators.
This patch introduces a new _parent_ API to expose such functionality in
a vendor agnostic way. Consider this API as experimental for now, until
we have other usecases.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The stm32G0 device has a one APB peripheral clock bus
but splitted on two RCC registers: RCC_ABPENR1 and RCC_ABPENR2
Peripherals are on one or the other.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In Infineon XMC4XXX SoCs, gpio interrupts are triggered via an
Event Request Unit (ERU) module. A subset of the gpios are
connected to the ERU. The ERU monitors edge triggers and creates
a SR.
This driver configures the ERU for a target port/pin combination
for rising/falling edge events. Note that the ERU module does
not generate SR based on the gpio level. Internally the ERU
tracks the *status* of an event. The status is set on a positive
edge and unset on a negative edge (or vice-versa depending on
the configuration). The value of the status is used to implement
a level triggered interrupt; The ISR checks the status flag and
calls the callback function if the status is set.
The ERU configurations for supported port/pin combinations are
stored in a devicetree file dts/arm/infineon/xmc4xxx_x_x-intc.dtsi.
The configurations are stored in the opaque array
uint16 port_line_mapping[].
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Reset controller node is necessary to enable support for resetting
peripherials using RCC.
This patch also includes RCC reset registers offsets used by STM32_RESET
macro.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
This driver exposes STM32 RCC reset functionality through reset API.
Information about RCC register offset and bit is encoded just like GD32.
The first 5 least significant bits contains register bit number.
Next 12 bits are used to keep RCC register offset. Remaining bits are
unused.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
The stm32 devices which have a HSI48 clock possibility.
for stm32F0, stm32G0, stm32G4, stm32H7, stm32L0,
stm32L4, stm32L5, stm32U5, stm32WB
Signed-off-by: Francois Ramu <francois.ramu@st.com>
- Similar to what was done for other parts of the driver, remove any
register specification from Devicetree (modesel-reg/mask)
- Keep all the information in the driver, and define modes as "numbers",
e.g. PCA9420_MODE0: 0, PCA9420_MODE1: 1, etc.
- Bindings provide IC defaults now (all modes allowed 0/1/2/3 and
initial mode set to 0).
- When mode is controlled via the MODESEL0/1 pins (ie directly by an iMX
MCU using the dedicated PMIC_MODE0/1 pins), the driver will not allow
to select a mode (it is not possible). This mode is now enabled by
setting `nxp,enable-modesel-pins` in Devicetree. When enabled, all the
allowed modes are configured to be selectable via pins. When disabled,
mode can be set via I2C (using TOP_CNTL3 MODE0/1_I2C fields)
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add bindings for Aspeed AST10x0 reset driver. The reset line can be
de-asserted or asserted through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Microchip XEC GPIO pins support inverting the output of
alternate pin functions. This feature may be useful for
those peripherals that do not implement output inversion
in the peripheral. GPIO control register pad input and
parallel input register values are not affected by the
function output invert feature. GPIO interrupt detection
of an output is inverted if the invert polarity is enabled.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
pca9420_i2c.h has neem remamed to pca9420.h (device only has I2C, so
it's kind of redundant to have i2c in the header name).
pmic_i2c.h was again not generic but designed specifically for PCA9420.
All its macros have been renamed, s/PMIC/PCA9420, and moved to the
pca9420.h header.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The driver had a conceptual issue regarding current limitation. PCA9420
is able to limit the current flowing through VIN, ie input current. This
is a global setting, not individual to each regulator. This patch
creates a new DT property: nxp,vin-ilim-microamp to specify such limit.
It is applied when the device is initialized.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Voltage ranges were hardcoded in Devicetree, however, things can be
significantly simplified by using the recently introduce linear ranges
API. All values are now computed using information stored in the driver,
so there is no need to store any lookup table in ROM. Code should now
both be faster in average and consume less ROM.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Regulator registers were set for each BUCK/LDO in DT, likely because of
the way the devices were instantiated. When using a generic iterator,
ie, DT_INST_FOREACH_CHILD, there's no way to differentiate the child
being _parsed_. Since instantiation happens now based on child node
names, we are able to know which registers each devices gets assigned at
the driver level. This greatly simplifies Devicetree, and it actually
removes information that is not strictly hardware description from it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PCA9420 dt-bindings include file defines all device registers, but
many of them are not used (e.g. battery charger). It is also not the way
to use register definitions. Devicetree is about hardware description
after all. File will be cleaned up in subsequent commits.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In npcx ec series, two detection levels, 3.3V (default) and 1.8V are
supported during gpio configuration. But the current implementation
always selects default detection level whether NPCX_GPIO_VOLTAGE_1P8 is
set. This PR is a fix for this issue.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
For STM32F1, F4 & L1 series, add the definition of SYSCLK to solve a
regression concerning the RTC counter
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Such generic flags were replaced for vendor-specific flags. Zephyr
releases 3.1 and 3.2 have shipped with the flags deprecated, it is now
time to remove them.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The NPCX driver did use deprecated voltage macros. Define vendor
specific flags instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
For all STM32 series, add some defines to select the RTC clock source.
This change is necessary to be able to select the RTC clock source in
dts instead of Kconfig
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
A USB TypeC connector has many peripherals associated with
it and the DTS binding in this commit provides a way to group
peripherals and properties in a device tree.
This binding is used with the USB-C Subsytem.
This is based on Linux, documentation:
https://www.kernel.org/doc/Documentation/devicetree/bindings/connector/usb-connector.yaml
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Doxygen docs for a macro need to be placed together with the macro being
documented (unless using `@def`).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Documentation for STM32*_PINMUX macros was incorrectly placed above the
macro, so it was in practice documenting the next macro (e.g.
STM32_MODE_SHIFT).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce support for Pinctrl driver on NXP S32Z/E SoC's.
The NXP S32 pin controller is a singleton node responsible for
controlling the pin function selection and pin properties, based on the
pin node group approach. The pinmux configuration is encoded in a
32-bit value.
Each S32 SoC implementing Pinctrl must create a `pinctrl_soc.h` header
which define SoC-specific macros to initialize the pinctrl structure.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Update regulator binding definitions for PCA9420 to support mode setting
features. This will allow the 4 voltage modes present on the PCA9420 PMIC
to be utilized.
Note that bindings have also been updated to indicate the default
register value and target voltage for each regulator on the PCA9420.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This adds a very basic driver to utilize the I3C IP block
on MCUX (e.g. RT685). Note that, for now, this only supports
being the active controller on the bus.
Origin: NXP MCUXpresso SDK
License: BSD 3-Clause
URL: https://github.com/zephyrproject-rtos/hal_nxp
Commit: 2302a1e94f5bc00ce59db4e249b688ad2e959f58
Purpose: Enabling the I3C controller on RT685.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Define RaspberryPi Pico ADC.
The ADC has internally connected temperature sensor,
Add property to enable this.
The ADC has a single VREF. VCC usually connects to it,
but it may not be in a case.
Add property to make configurable it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
This patch adds a clock control driver for GD32 platforms. It is
important to note that the driver is only able to handle peripheral
clocks, but not "system clocks" (e.g. PLL settings, SYS_CK, etc.). On
some similar platforms (STM32) this task is embedded in the same clock
driver, performed at init time but with no options to do any
manipulation at runtime via the API calls. The clock control API as-is
is really orthogonal to "system clocks", and it is arguably a bad idea
to embed system clock init code in a clock control driver. It can be
done at SoC level still using Devicetree as a source of hardware
description/initial configuration.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Added code to enable platform specific Virtual Wire GPIOs. With this
change, able to send the USB-C overcurrent Virtual Wire event to
Meterolake SOC.
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
The bindings for the stm32f105 afio pin remap had defined the wrong
offset for CAN and ETH.
This commit corrects those to the bits specified in RM0008 Rev.21,
but the changes could not be verfied on hw.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Adjust the names of the operating modes to match them
with the datasheet and INA230 pattern. While at it add
the missing INA237_OPER_MODE_TEMP_TRIG mode.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Add a new reset driver for GD32 platforms. This driver controls the
reset registers from the RCU peripheral. It can be used to restore
peripherals to their initial state when initializing a device.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
It was not possible to disconnect a pin using the nRF pinctrl driver.
That is, it was not possible to set PSEL to 0xFFFFFFFF (indicating pin
is not connected). This can be useful in certain scenarios, e.g. a
bootloader configures all signals of a certain peripheral but
application then needs to disconnect certain signals.
A new DT macro has been introduced to accomplish this:
NRF_PSEL_DISCONNECT. It can be used like this to explicitely disconnect
a peripheral signal:
```
&pinctrl {
uart0_default: uart0_default {
group1 {
psels = <NRF_PSEL(UART_TX, 0, 1)>,
<NRF_PSEL_DISCONNECTED(UART_RX)>;
};
};
};
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add spi0 and spi1 configuration to rp2040.
spi0 and spi1 are declared as compatible with
"raspberrypi,pico-spi" and "arm,pl022".
"raspberrypi,pico-spi" is just inherited from
"arm,pl022" and "reset-device"
spi0 and spi1 declare as compatible with "raspberrypi,pico-spi"
and "arm,pl022".
"raspberrypi,pico-spi" is just inheriting "arm,pl022" and
"reset-device" for declaring the 'reset' property,
with no additional property and implementation.
Add also pinctrl macros to dt-bindings header.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
After some analysis I found out that there's no machine timer provided
by the "riscv" vendor. There are some specs for the mtime/mtimecmp
registers (this is why we can have a single driver), but the actual
register layout or implementations differ amongst vendors. GD32 uses the
Nuclei implementation, named "system timer" in their documentation. This
patch aligns with vendor specs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add binding for Aspeed AST10x0 clock driver. The clocks can be turned
on or off through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
This commit adds the pll2 and pll3 clock control nodes
with st,stm32u5-pll-clock compatible.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
HSE is a valid alternate clock source for these series,
therefore STM32_SRC_HSE is added in this commit.
Both series can use HSE as an alternate clock source for USB and FDCAN.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Clean up unused psl functions in scfg.c, unused DT macros, unused psl DT
nodes and related yaml files. Currently, PSL pad configurations are made
by pinctrl mechanism. Please refer
https://issuetracker.google.com/234861079 for more detail.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Now that we have 8 bits reserved for vendor specific GPIO flags,
introduce a new set of flags for nRF platforms to configure pins drive
mode. These new flags are equivalent to the previous existing ones, but
use a naming scheme the fits better with vendor hardware capabilities.
The table below shows the equivalence between old and new flag
| Old flags | New flags |
|---------------------------|-----------------------|
| `NRF_GPIO_DS_DFLT_LOW` | `NRF_GPIO_DRIVE_S0` |
| `NRF_GPIO_DS_DFLT_HIGH` | `NRF_GPIO_DRIVE_S1` |
| `NRF_GPIO_DS_ALT_LOW` | `NRF_GPIO_DRIVE_H0` |
| `NRF_GPIO_DS_ALT_HIGH` | `NRF_GPIO_DRIVE_H1` |
| `NRF_GPIO_DS_DFLT` | `NRF_GPIO_DRIVE_S0S1` |
| `NRF_GPIO_DS_ALT` | `NRF_GPIO_DRIVE_H0H1` |
| `NRF_GPIO_DS_DFLT_LOW \|` | `NRF_GPIO_DRIVE_S0H1` |
| `NRF_GPIO_DS_ALT_HIGH` | |
| `NRF_GPIO_DS_ALT_LOW \|` | `NRF_GPIO_DRIVE_H0S1` |
| `NRF_GPIO_DS_DFLT_HIGH` | |
Documentation has been written to explain in more detail the meaning of
the flags and how they can be used.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The naming of the custom DS flags is not clear for nRF platforms. This
patch removes all the NRF_GPIO_DS* flags. New flags will be
re-introduced in a follow-up commit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
For now, on stm32f4 series, we only define PLL_P, PLL_Q and PLL_R
source clocks are they are required by the driver to allow configuration
of respective PLL outputs.
No other source clock are supported yet.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32_SRC_xxx definitions which are needed
for some peripherals of the stm32f4 soc.
Only the minimum clock sources are listed.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit introduces bindings that allow socs compatible with the
stm32 common driver to use the pll outputs pll_p, pll_q, pll_r,
to be used as a clock source for peripherals.
These are to be used instead of the, now removed, STM32_SRC_PLLCLK.
Applies to: STM32G0, STM32G4, STM32L4, STM32L5, STM32WB, and STM32WL.
STM32F2, and STM32F4 are not considered: very similar but only very limited
configuration possible. Only I2S(EXTclock,PLL_R), MC01, MCO2,
PLL_Q for 48MHz clock, and PLL_P as PLLCLK.
Doesn't apply to STM32L0, and STM32L1 which only have PLLMUL and PLLDIV.
Doesn't apply to STM32F0, STM32F1, STM32F3 only having a PLLMUL,
and no divider.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The STM32_SRC_CLOCK_MIN and STM32_SRC_CLOCK_MAX defines
are not really needed because non valid clock sources are already
filtered out by the precompiler.
Only STM32_SRC_CLOCK_MIN was used once in code and can be replaced.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Some device clock sources selection helpers were not correctly defined.
With this commit the definitions are updated to match the desciption
in the reference manual RM0453.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit is reworking clock definition in
order to match linux filetree and definition
as much as possible.
- dt-bindings: rework renesas clocks dt-bindings
- regroup renesas related dt-bindings in a folder
- rename renesas rcar common dt-binding to match linux name
- add soc specific dt-binding matching linux name
- soc dt-bindings are defining clocks matching linux names
- dts: use new clocks names
- move clocks definitions in SoC layer for each core clock entry
- driver: use new clocks names
As seen in this commit, we are declaring clocks for "R8A7795" SoC
to match linux names.
Linux is not declaring "R8A77951" SoC specific files because
its also supporting the first H3 SoC version numbered "R8A77950".
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
All STM32G0 SoCs have two sets of APB registers(APB1 and APB2).
Therefore set STM32_PERIPH_BUS_MAX to 0x40 (STM32_CLOCK_BUS_APB2)
for this series.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Add Doxygen tags to dt-bindings/pwm/pwm.h so that the binding macros
show up on the documentation page.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add inclusions of header files with devicetree related ADC definitions
to the nRF SoC dtsi files so that those definitions can be used also
for nRF SoC based boards.
Provide definitions of nRF ADC and SAADC analog inputs suitable
for use in devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The new octoSPI flash controller driver
requires parameter to configure the peripheral
especially matching the data mode and the transfer rate
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add clock sources bindings on F0/F3/G0/G4/L0/L1/L4/WB/WL series.
Due to inconsistencies, some common bindings are now split:
F1 -> F0/F1/F3
L4 -> L4/G4/WB
Update .dtsi files when required
In a first step, allowed sources are limited to already supported
clocks: LSI/LSE/HSI/HSE/MSI/PCLK/PLLCLK/SYSCLK
Support for other clocks such as HSI48, SAIXCLK, ... is left for a
next step.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename and factorize clock source bindings accessors by moving them
in common header file stm32_clock_control and remove them from
include/dt-bindings/clock/stm32XY_clock.h files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This new binding allows to work on providing stm32u5 specific
alternate and complementary device clocks.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to bring consistency in-tree, migrate all includes within
include directory to the new prefix <zephyr/...>. Note that the
conversion has been scripted, refer to zephyrproject-rtos#45388 for more
details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to be consistent with what is possible in Devicetree, always
take a period in nanoseconds. Other scales or units may be specified by
using, e.g., the PWM_MSEC() macros (all of them converting down to
nanoseconds). This change then deletes the "_nsec" and "_usec" versions
of the pwm_set call.
Note that this change limits the period to UINT32_MAX nanoseconds,
~4.3s. PWM is, in generali, used with periods below the second so it
should not be a problem.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In a first place, the PWM API operates on "channels", not "pins". While
the API calls could have been changed by _channel, this patch takes the
approach of just dropping _pin. The main reason is that all API calls
operate by definition on a channel basis, so it is a bit redundant to
make this part of the name. Because the `_dt` variants of the calls are
going to be introduced soon, the change to `_channels` + `_dt` would
make API function names quite long.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a pair of dt macros for specifying the pwm frequency in hertz or
kilohertz: PWM_HZ and PWM_KHZ. This is then converted in period
nanoseconds so it works as expected with the other definitions.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix STM32 clock dt-bindings location as they were added during
the shift of bt-bindings location from include to include/zephyr.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Files should not be in the root include/ directory but instead under
the zephyr/ prefix path.
Issue #41543
Signed-off-by: Yuval Peress <peress@google.com>
Add pinctrl driver for CC13XX/CC26XX family of SoCs
to facilitate transition from pinmux to pinctrl.
`IOCPortConfigureSet()` from TI hal driverlib used to
implement the generic pinctrl driver.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Move include paths and add new target_include_directories to support
backwards compatibility:
* /include -> /include/zephyr
example: <irq.h> -> <zephyr/irq.h>
Issue #41543
Signed-off-by: Yuval Peress <peress@google.com>
