Fix the following compilation warning:
```
Warning (unit_address_format): /memory@0xb0000000: \
unit name should not have leading "0x"
```
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Remove nxp,imx-mu-rev2 compatible. This IP block is the same as the
nxp,imx-mu device, and should be handled by the same compatible
Instead, use CONFIG_HAS_MCUX to determine which HAL APIs should be used
to interact with the messaging unit IP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Updates Ethernet PHY devicetree bindings to be more consistent with
Linux by using the standard `reg` property for the PHY address instead
of a custom `address` property. As a result, MDIO controller bindings
now require standard `#address-cells` and `#size-cells` properties.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Update the descriptions for the various CAN devicetree timing properties
specified in Time Quanta (TQ) to make it clear that these, if present, are
only used for the initial timing parameters.
Deprecate the (Re-)Synchronization Jump Width (SJW) devicetree properties
for both arbitration and data phase timing as these are now only used in
combination with the other TQ-based CAN timing properties, which are all
deprecated.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add `mdio_read_c45()`/`mdio_write_c45()` APIs for Clause 45 access
and remove the `protocol` MDIO binding property so that MDIO bus
controller can support more than one protocol.
A new MDIO header is introduced with generic opcodes, MMD and
registers addresses, to be used by MDIO and PHY drivers.
Existing MDIO drivers that support both Clause 22 and Clause 45
access are migrated to the new APIs.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
LP/HP RING OSC clocks were replaced by the ACE IPLL clock.
If needed IPLL can be configured to work as low power clock. But right
now ACE uses only WOVCRO and IPLL (configured to work as HP RING OSC
clock).
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
LP/HP RING OSC clocks were replaced by the ACE IPLL clock.
If needed IPLL can be configured to work as low power clock. But right
now ACE uses only WOVCRO and IPLL (configured to work as HP RING OSC
clock).
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
The ACE family platforms do not have LP/HP RING OSC clocks. They were
replaced by the ACE IP integrated PLL clock. Selecting LP or HP in
CLKCTL will result in enabling IPLL.
Clock can supply frequencies for both replaced clocks, default frequency
equals to 393.2 MHz.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
The ACE family platforms do not have LP/HP RING OSC clocks. They were
replaced by the ACE IP integrated PLL clock. Selecting LP or HP in
CLKCTL will result in enabling IPLL.
Clock can supply frequencies for both replaced clocks, default frequency
equals to 393.2 MHz.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
The zdsp.basicmath needs a bit more ROM space to run.
So enlarge the indicated ROM size to accommodate that.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add missing definitions for ALH DAIs. Keep the same FIXME
reminder in the comments we have for ACE1.5 that explains
the background of these definitions.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
To properly setup L1 exit timing this patch will use buffer interrupt
for HOST DMA and wait for Host HDA to actually start
First interrupt will clear all others.
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
This adds SoC and board configs to support the dc233c core
that is available on QEMU. This core has more features than
sample_controller, such as MMU support.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
On ACE a seperate, soc specific, interrupt mask needs to be enabled
to unmask the interrupt. Do so for GPDMA.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add mailbox and interrupt-controller nodes used for
inter-process communication.
Add also the dt binding for the interrupt-controller.
For now, this is used just to fix some compile errors,
since the mailbox requires an interrupt-controller.
For DSP, we have a direct interrupt line to the core.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Introduce dtsi files representing the
current portfolio of chips and modules
based on the followint criteria:
- flash size
- psram size
- gpio count
- certification status
Update the boards dts files according
to which SOC/SIP they are using.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
CPU idle states are not board specific. This patch moves ESP32 idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
- Add overlay for the esp32s2_saola board to die_temp_polling sample.
- Add aliases for the die_temp_polling sample to esp32s2 dtsi.
Signed-off-by: Hiroki Tada <tada.hiroki@fujitsu.com>
Add simple mechanism to load the image from IMR memory. Basically we are
only setting a flag in power off for the next boot to jump to existing
image in IMR.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
The ACE 2.0 LNL platform has 5 HIFI4 cores. Change number
of cores to enable 5th core on the platform.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Added i-cache-line-size and d-cache-line-size values
to device tree for ace20_lnl platforms. These values
are used by sys_cache_instr_line_size_get and
sys_cache_data_line_size_get functions.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Add GDMA support for esp32s3.
Remove suspend/resume since they are optional and do
the same as start/stop.
Fix possible null pointer derreference.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Enable UART on the DSP from the i.MX8MP target:
- add corresponding nodes in dtsi and dts;
- create a dts overlay for uart;
- add a config fragment for uart and console configuration.
So, in order to compile an application and enable UART
a user must run west build using DTC_OVERLAY_FILE and CONF_FILE.
Here's an example for hello_world:
west build -p always -b nxp_adsp_imx8m samples/hello_world/
-DDTC_OVERLAY_FILE="boards/xtensa/nxp_adsp_imx8m/
nxp_adsp_imx8m_uart.overlay" -DCONF_FILE="boards/xtensa/nxp_adsp_imx8m/
nxp_adsp_imx8m_uart.conf"
For other applications, like SOF, where we don't need UART, we simply run:
west build -p always -b nxp_adsp_imx8m ../modules/audio/sof/ --
-DTOOLCHAIN=/opt/zephyr-sdk-0.15.2/xtensa-nxp_imx8m_adsp_zephyr-elf/
bin/xtensa-nxp_imx8m_adsp_zephyr-elf -DINIT_CONFIG=imx8m_defconfig
The nxp_adsp_imx8m is using the nxp_imx_iuart driver.
For now, is used in poll mode.
Next step is to enable the interrupt controller in
DSP and use the interrupt driver UART.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
CAVS platforms are not fully integrated with zephyr. Some of the
registers are still programed from SOF side. This feature can be enabled
for those platforms later when integration is fully done.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
This patch adds HDA to device tree for LNL platforms.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The I2CLCTL_MLCS setting was recently added to MTL
platform. LNL has these registers in separate space, therefore
new field is added to intel,ssp-dai.yaml and appropraite definitions
to LNL device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Repleace usage of shim2 device tree field with hdamlssp.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In ACE 2.0 platform (LNL) dmic got two new shim register ranges.
DMIC driver need to program them to configure the interface.
This patch adds new shims to device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Sort SoC nodes by address to make it easier to find them. As part
of this also move the intel-sha node under SoC where it belongs.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
In ACE 2.0 platform (LNL) ssp got new shim registers.
SSP driver need to program them to configure the interface.
This patch adds new shims to device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
As the power domain nodes don't represent something accessible via
a MMIO register move those under the lps node to address warnings
generated when building the DTS.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
LNL platform is ACE 2.0 series with changes in shim registers and HW
features. Initial definition replicates MTL as much as possible, however
it will vary after enabling LNL platform.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds definition of ACE 2.0 Lunar Lake board.board.
Signed-off-by: Krzysztof Frydryk <Krzysztofx.Frydryk@intel.com>
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add LEDC device for esp32s3
Update PWM LED binding
Remove invalid comment from driver source file
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Changed the watchdog driver used by the ACE platform from
snps,designware-watchdog to intel,adsp-watchdog.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Start using zephyr power management in cavs platform in a similar way
that is already done in ace. This commit only addresses the power off/on
sequence. Runtime power management is not implemented.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Fixes the warning below. This commit does not change the firmware
binary. Thanks Kumar Gala for the suggestion.
build-mtl/zephyr/zephyr.dts:279.42-285.5: Warning (simple_bus_reg):
/soc/ace_comm_widget@71C00: simple-bus unit address format error,
expected "71c00"
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Intel DSP Communication Widget is a device for generic sideband
message transmit/receive between IPs in a SOC.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
ALH dts definitions need to have 16 nodes, thus add them to supported
platforms (cavs25 and ace15).
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Add virtual memory entry in dt to use as virtual space
regions for aplication.
Add virtual memory definition in adsp_memory.h
Signed-off-by: Jakub Dabek <jakub.dabek@intel.com>
Adds two additional alh2 and alh3 "devices" to already defined
alh0 and alh1. This (seems) is a temporarily solution as
the hardware actually supports 16 streams and future update
to device tree is required.
Signed-off-by: Serhiy Katsyuba <serhiy.katsyuba@intel.com>
Assigning power domain to the GP DMA.
NOTE: Only controllers 1 and 2 are under IO_0 domain, controller 0 is
under HUB-ULP domain.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Support for the measuring the CPU die temperature
for the ESP32 targets S2,C3. The ESP32 support
was ommited due to lack of offset calibration.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Add definitions for DMAs, Digital Audio Interfaces (DAIs) and
the necessary clocks to enable full use of audio peripherals
in the intel_adsp_cavs25_tgph boards.
Link: https://github.com/thesofproject/sof/issues/6710
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
add Intel HDA DAI driver
Long device list in dtsi needs to be refactored in the future
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Added i-cache-line-size and d-cache-line-size values
to device tree for cavs and ace platforms. These values
are used by sys_cache_instr_line_size_get and
sys_cache_data_line_size_get functions.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Added to the device tree values of the dma-copy-alignment
and dma-buf-size-alignment attributes.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Added to the device tree values of the dma-copy-alignment
and dma-buf-size-alignment attributes.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Renamed the dma-buf-alignment field to a more explicit
and descriptive name dma-buf-addr-alignment.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Sort SoC nodes by address to make it easier to find them. As part
of this also move the intel-sha node under SoC where it belongs.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
"alh0: alh1:" will create only one instance and this needs to be
reverted to original form with two instances
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
As the power domain nodes don't represent something accessible via
a MMIO register move those under the lps node to address warnings
generated when building the DTS.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Cavs25 alh definition is currently the same as in ace platform, which is
wrong, thus fix it.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Convert timer driver to use a light weight syscon and DTS and convert
register information to use offsets and sys_read/sys_write instead of
structs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is not guaranteed to match the physical layout of the memory, so
get them individually based on node label.
For initialization, use bbzero.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some windows might need to be set as writtable, so add a flag read-only
to DTS bindings which is set to true for all windows right now. This can
be set to false where needed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Instead of just declaring the memory window register in DTS and have
everything else all over the place (headers, Kconfig, etc.) this change
defines the memory window instances in DTS and uses the device model to
initialize the windows. Code is still part of the SoC, given that we do
not have a driver subsystem suitable for this type of device yet.
Move FW status to own workflow and separate from window setup.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add Intel dmic dai dts definitions for ace15, cavs15 and cavs25
platforms.
Add also pre dts cmake files as the dmic nodes use same address and emit
warnings otherwise.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
