Define CANPLL, an AUXPLL IP instance used by the CAN IP. PLL settings
are hardcoded in SoC files, as this PLL should not be configured by the
application. It is meant to always run at 80 MHz.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Define HFXO (High Frequency Crystal Oscillator). This clock is managed
by system controller, from an application point of view it is a fixed
clock.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add a definition of SUIT storage, so there will be a common source of
the SUIT storage location for both SDFW and scripts generating SUIT
storage areas, assigned to local domains.
Signed-off-by: Tomasz Chyrowicz <tomasz.chyrowicz@nordicsemi.no>
Remove the "snps,designware-spi" compatible from the EXMIF node in
nRF54H20i, as the spi_dw driver cannot be used for this peripheral
without Nordic-specific modifications that are not present upstream.
An attempt to do so (just setting CONFIG_SPI=y will cause that,
as the driver initialization function will be executed then) results
in a bus fault.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add driver, together with the corresponding dts binding and node in
the nRF54H20 SoC definiton, for the nRF temperature sensor that cannot
be accessed directly but only through nRF Services (nrfs) layer.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit adds an ieee802154 node to the list of nRF54H20 application
core's peripherals. While it does not translate directly into a physical
RADIO peripheral, it represents the capability to use the ieee802154
radio indirectly through cpurad.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Move the Domain IDs from `nrf54h20.dtsi` into its own header file.
Additionally, include another header with Owner IDs.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
The counter driver needs to know what is the maximum
counting frequency of each timer peripheral.
Let's add it to its DT.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Added EXMIF peripheral DTS description and bindings.
The peripheral operates as an SPI device.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Squash the two copies of this file found in `dts/arm` and `dts/arm64`.
Their contents were identical up to devicetree property ordering.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add a VEVIF node to be used for communicating with SysCtrl (cpusys).
This is the only part of the SysCtrl VPR exposed to local domains.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add definitions of PWM peripheral instances so it can be utilized
on nRF54H20 and nRF54L15 devices.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add definition of the nRF54H20 SoC with its Application, Radio,
and Peripheral Processor (PPR) cores and an initial set of
peripherals.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit 4db40601dd.
There are two ECB instances in nRF54H20 and the above commit added
only one of them.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
And add the corresponding bindings.
Move alse the already existing bindings for nrf-dppic, nrf-ppi,
and nrf-ipc so they are located together with the new ones and
in more appropriate folders (DPPIC and PPI peripherals are not
related to ARM, and IPC is for sending and receiving events,
not messages, so ipm/ does not seem to be the best fit for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The MRAM has no concept of erase blocks or pages, so this is treated as
driver configuration.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add a new nodes for PPR's VEVIF. In app cores, VEVIF registers are part
of the VPR peripheral, so it is exposed as a child node (since it
requires its own properties, eg #mbox-cells). In VPR, it's a CPU child
since it's not a memory-mapped peripheral, but used with CSRs.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This is a setting that depends on the board or application, so it should
not be part of SoC definition files.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
... so that there is no need to include that header individually
for every added board based on an nRF SoC.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add definition of the nRF54H20 SoC revision EngA with its Application,
Radio, and Peripheral Processor (PPR) cores and basic peripherals:
GRTC, GPIOs, GPIOTE, and UARTs.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... so that it can be included by ARM and RISC-V cores. For the same
reason, SysTick can no longer be disabled in this common file.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Provided nodes reflect the clock tree of each series.
Clock nodes are disabled by default but populated with default
start up configuration. Main reason is the we don't want to
impact boards using Kconfig based clock configuration for now.
Exception to these rules:
- syslck: Default enabled, clock frequency and clock source not
provided
- pll: clock source not provided
This is made on purpose so that errors are triggered if parameters
essential to the board configuration are not provided.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since there are times that we include a base .dtsi file and change the
reg address we tend to end up with warnings that the reg address and
unit-address don't match. To handle this introduce a simple DT_ADDR(x)
macro that will prepend '0x' to a 'unit-address' style address.
#define DCCM_ADDR 80000000 /* in unit-address format */
dccm0: dccm@DCCM_ADDR {
reg = <DT_ADDR(DCCM_ADDR) 0x1>;
...
};
This allows the dts file to override the value of DCCM_ADDR and than to
have the unit-address of the node and the reg address match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove the common.dts file which has been used for a year.
common.dts at one point allowed us to conditionally add an MCUBoot
overlay based on Kconfig.
but since DT lost access to Kconfig options it has been unused.
The overridable variable DTS_COMMON_OVERLAYS, which by default points
to common.dts, is also unused in-tree, and any out-of-tree usage can
be ported over to use DTC_OVERLAY_FILE instead, so we remove the
variable as well.
This simplifies the configuration system.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
