Previous value just activated the ability to trigger for both edges,
without (de)-activating the gpio. This caused an assrtion error in GPIO.h.
Fixes#71227
Signed-off-by: Juliane Schulze <juliane.schulze@deveritec.com>
Although we can get the number of configured OUT and IN endpoints and
endpoint capabilities from the DWC GHWCFGn registers, we need to
configure the number of endpoint configuration structs at build time. On
some platforms, we cannot access the hardware register at pre-init, so
we use the GHWCFGn values from the devicetree to provide endpoint
capabilities. This can be considered a workaround, and we may change the
upper layer internals to avoid it in the future.
Also, add a new vendor quirk to fill in platform-specific controller
capabilities.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add driver for TSic 206/306/316/506F/516/716 temperature sensor.
The driver uses PWM capture driver to read a single wire with
Manchester-like encoding.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Move it to a common file named `zephyr,memory-common.yaml`, which
replaces `zephyr,memory-attr.yaml` and takes its contents as well.
This is so that another binding, e.g., `vnd,memory-region`, can support
being combined with the `zephyr,memory-region` binding like so:
node@deadbeef {
compatible = "vnd,memory-region", "zephyr,memory-region";
zephyr,memory-region = "NAME";
...
};
To allow this, edtlib would require `vnd,memory-region` to include the
property definitions from this new common file.
The same can't be done by including `zephyr,memory-region.yaml` directly
because that file marks the property in question as always required, and
it shouldn't be required whenever the `vnd,memory-region` compatible is
used on its own.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
The gpio-emul driver does not actually require any reg property,
since it is not in the physical memory map of any device. So
let's remove that property from the bindings.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Remove all CAN controller "bus-speed" and "bus-speed-data"
properties. These all use the default bitrates set via Kconfig.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Set the default initial bitrates globally via Kconfig. The initial bitrates
can still be overridden using the "bus-speed" and "bus-speed-data"
devicetree properties.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove nxp_ground_select property.
Delete the use of NXP vref peripheral CSR register REFL_GRL_SEL bit.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
PHYTEC has multiple offices in different locations like
the US, France, India and China. The headquarter is located in
Germany. Since now 50% of the PHYTEC boards are from the US
office, we should drop 'Messtechnik GmbH', which is the offical
title of the German office, and keep the name more general.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The new bindings for the stm32 xspi is for new stm32 devices with
XSPI peripherals like the stm32h5 serie. This is close to the octo-spi.
Adapt the flash controller constants to the XSPI model especially.
This is done through a new xspi.h definition file.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add driver, together with the corresponding dts binding and node in
the nRF54H20 SoC definiton, for the nRF temperature sensor that cannot
be accessed directly but only through nRF Services (nrfs) layer.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit makes the devicetrees of the targets that are based on the QEMU
`virt` machine more consistent with the rest of the RISC-V targets in
Zephyr by:
* adding the `riscv,isa` property
* adding a compatible string which uniquely identifies the `virt` core
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The CSI can connect to either a camera sensor (as on i.MX RT10xx) or
a MIPI CSI-2 receiver (as on i.MX RT11xx). To be generic, change the
naming from sensor to source.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Add initial HID device support. Unlike the existing HID implementation,
the new implementation uses a devicetree to instantiate a HID device.
To the user, the HID device appears as a normal Zephyr RTOS device.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The clk, dqs and ncs pins can be remapped between OSPI instances, but the
driver doesn't support it, yet. Therefore replace hard coded numbers to
device tree optional properties.
Signed-off-by: Samuel Kleiser <s.kleiser@vega.com>
Allow configuration of the system pll on the iMXRT10xx series parts, via
a fractional pll node under the CCM module.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Adding required flag to the current-speed as without this driver
does not compile.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Gives number of the Extended Interrupts and Event Controller (EXTI)
interrupt line connected to the RTC Alarm event.
Used on all series, except WBAX & U5X, where RTC Alarm interrupt is
routed directly to Nested Vectored Interrupt Controller (NVIC) and to
Power Control (PWR) wake-up pins.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
This change allows to use DTR line driven from external serial port
that when active (low) will prevent UART device from going to sleep.
It will also wake up platform when DTR line becomes active.
DTR line is often activated in serial port connected to host computer
when operating system opens serial device like COMx for Windows
or /dev/ttyACMx /dev/ttyUSBx for Linux based systems.
DTR line (specified in device tree) will be used by WAKEUP and PDC
controllers (via GPIO driver) to handle DTR line changes.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This change allows to wake up UART from sleep mode when
low level on inactive UART is detected during platform sleep.
Timeout can be specified for each UART separately in device tree.
If one of the UARTs is selected as console sleep timeout is taken
from Kconfig same way other platform configure same functionality
using CONFIG_UART_CONSOLE_INPUT_EXPIRED_TIMEOUT
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
If no HSFLL needs trimming, then `trim_hsfll()` should be compiled out.
This makes it easier to reuse the rest of `soc.c` out of tree.
Furthermore, some HSFLL instances can be trimmed before booting Zephyr,
so the FICR client properties in the DT binding should not be required.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
The emulated GNSS driver behaves like a GNSS, implementing
device pm and the GNSS APIs, using only kernel features (
zephyr work queue and uptime) making it buildable on all
zephyr targets.
The purpose of this device driver is to tailor and validate
the gnss api test suite.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Add mfd_adp5585 and gpio_adp5585 driver. This driver enables ADP5585
as an GPIO expander.
This chip is used as an GPIO expander on i.MX93 EVK. GPIO pinctrl,
read/write and interrupt is supported.
Note that ADP5585 has 2 GPIO banks with 5 pins each. The driver combines
two group into a 16-bit port. Index 0~4 correspond to R0~R4 lines, index
8~12 correspond to C0~C4 lines. Index 5~7 is reserved unavailable.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
The counter driver needs to know what is the maximum
counting frequency of each timer peripheral.
Let's add it to its DT.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add binding for adi SDP-120 connector and header file
with marcos to map signals using signal names.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
Add driver for IS66WVQ8M4 PSRAM, using the MCUX FlexSPI interface to
write data to the PSRAM device.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Some instances of the FlexSPI IP support a different clock source being
used for port B of the FlexSPI instance. Add a devicetree property and
driver support to enable configuring this property of the hardware.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added EXMIF peripheral DTS description and bindings.
The peripheral operates as an SPI device.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Add support for similar adin1100 phy, boath are 10Base-T1L,
only difference is that adin1100 connects through r/mii.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
MDIO is part of the ETH IP, but some phy chip may need a
specific phy driver to set up certain vendor registers enabling
particular features.
Add support for stm32 mdio access.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Add Sequans GM02S modem binding using the sqn vendor prefix.
The modem has an active low reset signal.
Signed-off-by: Thibo Verheyde <thibo@dptechnics.com>
Intial driver adding intial script to receive only GGA, RMC and GSV
NMEA messages, configuring fix rate, setting enabled system and adding
power management with the module on-off pin.
Signed-off-by: Jeronimo Agullo <jeronimoagullo97@gmail.com>
Spell checking tools do not recognize "iff", replace with "if and only if".
See https://en.wikipedia.org/wiki/If_and_only_if
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Convert the ht16k33 to use the input subsystem. This can still be used
with the kscan API with the zephyr,kscan-input driver, or use the
input-keymap one to generate input codes instead.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add basic functionality of Renesas SD/MMC driver. It can be used
for both gen3 and gen4 R-car boards, but tested only with H3ULCB,
Salvator XS M3 and Spider boards. This driver working with SDHC
subsystem.
The driver supports regularal reading/writing throught SD/MMC
controller buffer, DMA mode w/o interrupts and timing tuning.
Add gpio5 and sd0 nodes to h3ulcb and salvator xs which are needed
for working with SD cards. The GPIO node is needed for switching
voltage on SD card through gpio regulator driver.
Notes:
* the driver doesn't support SPI mode;
* SCC tuning and DMA mode based on IRQs are enabled by default;
* an address of a data buffer has to be aligned to 128 bytes if it
is not, driver will use non-DMA mode automatically;
* Renesas MMC DMAC doesn't support 64-bit DMA addresses, so for
case when we have 64-bit xref data address we use non-DMA mode;
* SD/MMC controller supports block size between 512 and 1 with
a lot of restrictions, more details you can find in code;
* support of HS400 mode isn't implemented inside driver.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
Add device driver for TI TMP114 I2C temperature sensor.
The driver only support basic functionality, i.e. fetch temperature
using default values.
Datasheet:
https://www.ti.com/lit/ds/symlink/tmp114.pdf
Signed-off-by: Fredrik Gihl <fgihl@hotmail.com>
For historical reasons, inversion mode is enabled by default in the
current implementation. This commit introduces an `inversion-off`
boolean DTS property, allowing it to be disabled if necessary.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Adds support for the PGOOD pin. This pin is asserted by the
regulator when converter startup has completed and the output
is stable. If the PGOOD pin is not used, the PGOOD state is
check via the PGOOD_PIN_STS bit.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Deprecate the use of location_* properties in the i2c_gecko driver
and migrate to the pinctrl api for enhanced maintainability and
compliance with current standards.
Signed-off-by: Arunmani Alagarsamy <arunmani.a@capgemini.com>
This property will allow PWM driver allocate data buffer
in appropriate memory region.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Driver already handles the case when 'reset-gpios' is not provided, so
remove 'required: true' from bindings to allow boards / shields definition
without reset signal being connected to any Zephyr controlled GPIO.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
This commit refactors the Intel SSP DAI driver to support dynamic
management of SSP IP. This change additionally separates the management
of the DAI part from the management part of the SSP IP.
Key changes:
- Add new static functions to manage SSP IP power.
- Update the DAI SSP configuration functions to use the new management
approach.
- Update device tree bindings and instances to reflect the new SSP IP
management mechanism.
Signed-off-by: Damian Nikodem <damian.nikodem@intel.com>
The commit restricts erase-value to either 0xff or 0x00.
On program-erase type devices writes can only change from
erase value of bit to opposite, ease usually consists of two
operations which is programming the opposite value to every bit
of erase range and then turning back all bits to the "erase-value";
above makes it impossible to have erase value of device to be other
than 0xff or 0x00.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This implements basic driver to utilize the I3C IP block
on NPCX.
1. I3C mode: Main controller mode only.
2. Transfer: Support SDR only.
3. IBI: Support Hot-Join, IBI(MDB).
Controller request is not supported.
4. Support 3 I3C modules:
I3C1(3.3V), I3C2(1.8V, espi mode), (I3C3 1.8V or 3.3V)
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
add gpio_intel driver with acpi based resource enumeration support.
Also updated test cases overlay with new dts entires.
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
FTM internal counter can be clocked by one of three clock sources
independent of the module bus clock. This patch introduces a DT property
to perform the clock selection from DT.
DT sources are updated to keep the current clock selection for all boards,
with exception of ucans32k1sic board which is migrated to use system
clock by default, as this seems to be a better choice for most cases.
Some PWM LED samples require slower clock so overlays are added for
those cases.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add support for half-duplex (3-wire) SPI operation using the Raspberry
Pi Pico PIO. To allow control of the size of the driver, including
half-duplex support is optional, under the control of Kconfig options.
The original PIO source code is also included as a reference.
Corrected 3-wire tx/rx counts.
Enable half-duplex code based on DTS configuration
Replace runtime checks with static BUILD_ASSERT()
Remove too-fussy Kconfig options
Removed PIO source per review request
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
The MAC address macros are ridiculous in this driver.
Rewrite to be simpler and use eth.h common function.
Also, clarify the mac address generation on the DT overlays.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Adds a DAC driver for Texas Instruments DACx0501 family of devices
Signed-off-by: Eran Gal <erang@google.com>
Co-authored-by: Martin Jäger <17674105+martinjaeger@users.noreply.github.com>
Enable MIPI mode to be set via devicetree, for displays that support
multiple MIPI DBI modes. This commit also adds new helpers for displays
that allow drivers to initialize the entire MIPI DBI configuration
structure from devicetree
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Nuvoton NPCX chips have reset registers which allow to reset the
peripheral hardware modules. This commit adds the support by
implementing the reset driver. Note that only the reset_line_toggle API
is supported because of the nature of the reset controller's design.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Currently, all devices are initialized at boot time (following their
level and priority order). This patch introduces deferred
initialization: by setting the property `zephyr,deferred-init` on a
device on the devicetree, Zephyr will not initialized the device.
To initialize such devices, one has to call `device_init()`.
Deferred initialization is done by grouping all deferred devices on a
different ELF section. In this way, there's no need to consume more
memory to keep track of deferred devices. When `device_init()` is
called, Zephyr will scan the deferred devices section and call the
initialization function for the matching device. As this scanning is
done only during deferred device initialization, its cost should be
bearable.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
CSS was deprecated from the mcu-sdk. Removing driver from lpc55s36
to clear build error.
This is a temporary patch to remove the build error.
Fixes#69961
Signed-off-by: David Leach <david.leach@nxp.com>
Implement a sensor for the output diagnostics of the power train
switch TLE9104.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This commit enables pinctrl on i.MX8ULP. This includes:
1) Adding `pinctrl_soc.h` header file.
2) Adding DTS node for IOMUXC1, which is one of the
IPs responsible for managing the 8ULP pads.
3) Adding .dtsi with pin definitions. For now, only
the LPUART7 pads are added to this file because this
is going to be the only consummer for now.
4) Modifying the `pinctrl_imx.c` driver to work for 8ULP.
5) Enabling the `CONFIG_HAS_MCUX_IOMUXC`, which is a
dependency of `CONFIG_PINCTRL_IMX`.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add binding for sitronix ST7796s, a MIPI DBI display controller
supporting up to 320x480 displays at 18 BPP
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The SparkFun Pro Micro header pins are numbered D1, D0, GND, ... from top
left whereas the SparkFun Pro Micro RP2040 and the Adafruit KB2040 boards
are using gpio 0, 1, GND, ... , so the pro_micro: connector gpio-map of
these boards should reflect that.
Graphical Datasheet for SparkFun Pro Micro RP2040:
https://cdn.sparkfun.com/assets/e/2/7/6/b/ProMicroRP2040_Graphical_Datasheet.pdf
Graphical Datasheet for SparkFun Pro Micro:
https://cdn.sparkfun.com/assets/f/d/8/0/d/ProMicro16MHzv2.pdf
Pinout of the Adafruit KB2040:
https://learn.adafruit.com/assets/106984
Please note that the KB2040 uses CircuitPython pin labels D0, D1 which does
not seemt correspond to the Arduino labels D0 and D1 used by the Pro Micro.
Signed-off-by: Daniel Irekvist <ulmanyar@gmail.com>
Add devicetree binding for NXP LCDIC. This controller is capable of
driving displays in 8080 or SPI 3/4 wire mode, and optionally swapping
endianness of display data as it sends it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The initial version of an input driver for Cirque Pinnacle ASIC supports:
* Setting sensitivity
* Choosing between relative and absolute modes
* Relative mode
* Primary tap
* Swapping X and Y
* Absolute mode
* Setting number of idle packets
* Clipping coordinates outside of active range
* Scaling coordinates
* Inverting X and Y coordinates
Signed-off-by: Ilia Kharin <akscram@gmail.com>
For now DSI settings are hard-coded for the specific
LCD module used on the STM32H747I Discovery board
Signed-off-by: Erik Andersson <erian747@gmail.com>
To support the NT35510 display, some additional
options needs to be configurable in the STM32
DSI peripheral
Signed-off-by: Erik Andersson <erian747@gmail.com>
Add support for performing pinctrl operations. For now,
the only supported operation is applying the pinctrl default
state. Pinctrl is left optional to allow for scenarios in which
this is not required (e.g: AMP system in which another
OS configures the pinctrl).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add a property to select the push-pull GPIO output type to drive the
I2C recovery. The default is open-drain.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Based on the iis2dlpc driver, with some significant differences in
interrupt handling.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Add irqs to rzt2m gpio bindings in order to add interrupt support to rzt2m
gpio driver and adds common gpio node to store interrupt config (irqs are
shared between ports)
Signed-off-by: Jakub Michalski <jmichalski@internships.antmicro.com>
Remove the unused "tx-delay-comp-offset" property from the base CAN FD
controller devicetree binding.
Having a static Transmitter Delay Compensation (TDC) offset is useless.
The offset needs to match the data phase timing parameters in order to
properly configure the second sample point when transmitting CAN FD frames
with BRS enabled.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove ethernet-fixed-link binding as it is redundant with the
phy bindings. Clearly, ethernet does not work without the L1
layer, which is a phy device, or an integrated mac/phy device,
and all of these things should be described properly in DT.
The schema did not even come with a compatible, meaning nodelabels
were hardcoded into the drivers, which is unacceptable.
- Remove the binding file for ethernet-fixed-link.yaml.
- Remove fixed link functionality from the nxp s32 gmac driver.
Since this functionality is already covered by the phy support,
it is redundant.
- Remove fixed link include from the s32 gmac binding.
- Remove fixed link include from the nuvoton numaker binding.
As far as I can tell the corresonding driver does not even
use it anyways, and I did not find any board with this device
that describes a "fixed link".
- Move the definition into the nxp,kinetis-ethernet binding
as the eth_mcux driver, which is already being deprecated,
does use this, contain the debt to the legacy driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Added configuration of long press reset functionality.
Includes ship/hibernate to wake debounce time and
disabled/one_button/two_button mode selection.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
The DHT20 sensor is a temperature and humidity sensor that uses I2C to
communicate with a microcontroller. The DHT20 sensor is Aosong.
use standard crc
update description to add reference to AHT20 and AM2301B
clean code, use defines and bit manipulation
add dht20 to i2c test suite for build tests
update bit manipulation
use more defines instead of raw numbers
add bindings to allow aht20 or am2301b to be used in devicetree
in all 3 cases, the same dht20.c driver is compiled
Signed-off-by: Nathan Olff <nathan@kickmaker.net>
1. Update EDMA driver for version 4
2. The DMAMux module is not always present. Use the
feature define to make this optional.
3. Use the EDMA_SetChannelMux API for SoC's that supports
this feature.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add enum for `constant-charge-voltage-max-microvolt` property to
signalize improper values given with device tree at compile time.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Maximum charging current is selected with an external resistor in
the MAX20335 charger. Therefore it is not possible to configure it
with software directly. There is only a capability to limit current
set with hardware but configuration of the limiter is not
straight-forward.
To reflect real functionality, drop usage of
`constant-charge-current-max-microamp` property as an required one and
use custom `chgin-to-sys-current-limit-microamp` instead.
Use enum in binding file to signalize improper values at compile time.
Drop support for `CHARGER_PROP_CONSTANT_CHARGE_CURRENT_UA` API property
since this cannot be handled.
The `max20335_get_constant_charge_current()` function become useless so
remove it.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Rework the data scaling algorithm for the "deadzone" mode so that the
deadzone is subtracted from the input rather than from the output. This
makes the whole output range usable rather than making the output jump
from the center value to the minimum deadzone range.
This changes the calibration data structure as well so now all values
refer to the input data, which is more coherent.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Byte value written to the device's
ERXFCON: ETHERNET RECEIVE FILTER CONTROL REGISTER
Sets the devices receive packet filter, optional. If not set
in device tree previous hard coded value`0xA3` is used.
Uni, multi and broadcast packets with valid CRC are accepted.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
MODEM_UBX: Adds Support for UBX Messages in Modem Subsystem.
GNSS API Supported: get_supported_systems, set_fix_rate, get_fix_rate,
set_enabled_systems, get_enabled_systems, set_navigation_mode,
get_navigation_mode.
Boards Tested: MIMXRT1062_FMURT6, VMU_RT1170.
Note: Partial support for U-BLOX Messages is provided as of now.
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Signed-off-by: Mayank Mahajan <mayankmahajan.x@nxp.com>
The STTS22H is an ultralow-power, high-accuracy, digital temperature
sensor offering high performance over the entire operating temperature
range. This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/resource/en/datasheet/stts22h.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add ability to set a wakeup counter in case OS Timer is
disabled in certain low power modes. Also add code to
compensate the tick value.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Enables usage Bluetooth LE GATT as a serial endpoint to exchange data
using UART APIs. This implementation is compatible with UART Interrupt
Driven APIs and uses the nus-uart device-tree node properties to
configure FIFO buffers for transmitting and receiving. Defining
multiple instances of the driver is possible and it allows implementing
multiple GATT NUS service instances to exchange data as separate serial
endpoints.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
"RW pinctrl" is clearly SOC specific naming for an IP
that is not necessarily constrained to live on one SOC series.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Split up the driver for the PWM controller MAX31790
into a multi function device driver.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Some SAI instances are mutliline, meaning they can have multiple
TX/RX data lines (channels). Depending on the board, the index
of the TX/RX data lines that are connected to the consumer
(e.g: the codec) may not always be 0. This commit fixes this
issue by adding support for passing the index of the used
TX/RX data lines through the DTS.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Make the properties for setting the initial sample points for both the
classic/arbitration phase and the data phase optional.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Implement a sensor for the output diagnostics of the low side
switch BD8LB600FS.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Split up the driver for the low side switch BD8LB600FS into a GPIO
and MFD part.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This binding is for the NXP FlexComm Interface. The
driver will setup an interface for use as a UART, SPI
or I2C device.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Split the common keyboard scanning code out of the XEC specific driver
and use the generic code instead.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the XEC keyboard scanning driver from kscan to input, add the
corresponding kscan compatibility node to the current board, build test
only.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
And add the corresponding bindings.
Move alse the already existing bindings for nrf-dppic, nrf-ppi,
and nrf-ipc so they are located together with the new ones and
in more appropriate folders (DPPIC and PPI peripherals are not
related to ARM, and IPC is for sending and receiving events,
not messages, so ipm/ does not seem to be the best fit for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Some CAN transceivers have a lower limit on their supported bitrate. Add an
optional "min-bitrate" for specifying this limit via devicetree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add new devicetree bindings for F4 and L1 series for configuration of
block size used in flash write operations.
Allow byte-size write operations in `flash_stm32f1x.c`. This file is
being shared between F0, F1, F3, L0 and L1 series. L0 and L1 series
allows for single byte writes.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
Add Nuvoton numaker series flash memory controller(RMC) with erase,
read & write features of soc-flash.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add Open Alliance spi protocol support.
Open Alliance is a chunk-based SPI protocol, based on sending
over SPI an ethernet frame divided in smaller chunks, using a
specific 32-bit header for each chunk transferred. All chunks
can be sent or received by a single dma transfer.
Default mode is set to Open Alliance SPI without protection,
since the adin2111 dev. board comes shipped this way.
Tested:
- Open Alliance SPI, no protection (default board shipped)
- Open Alliance SPI, protection
- Generic SPI, no crc
- Generic SPI, with crc8
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Exhibit Renesas LCD controller's driver implementation. The driver
is intended to employ the controller in the continuous mode so
it can drive display panels in the parallel RGB mode.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Updating the nxp,pit driver to support mutliple
channels. Updating the dts and board overlays
to account for the changes.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Add a new binding that should help with samples or MBOX tests by getting
information from DT.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
For sharing pin definition property with `worldsemi,ws2812-gpio`,
rename `output-pin` to `gpios`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
ws2812-gpio's `in-gpios` property is not used as an input pin.
Renaming it to `gpios` to reflect the actual situation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
By default N_VBUSEN signal is used by the host to define if VBUS
signal should be used for power supply (VBUS-IPSOUT).
This feature enables the possbibility to change this behaviour.
When N_VBUSEN detection is disabled, axp192 will automatically
decide to use VBUS (REG10H[7] = 1).
Please refer to datasheet for details.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
AXP192 features an EXTEN pin that is on output only.
This commit appends control of EXTEN pin to gpio functionality
of AXP192.
Port-Mapping is as follows:
- [0..4]: GPIO0..4
- [5]: EXTEN
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
This adds the minimal get_time/set_time support for the rp2040 and
enables support by default on the Pico boards. This doesn't support
configuring the clock source or alarm interrupts yet.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
Utilization of chip interrupt line is mandatory to assure proper
charger state control. Handle interrupt to prepare the driver for
implementation of such functionality.
Modify charger status update so the current state is fetched in the
interrupt handler.
Use level based interrupts combined with interrupt disabling for a
period of time after interrupt handling to reduce number of interrupts
triggered by the charger. There may be a case where the charger
produces burst of interrupts for a several seconds and if the code
attempts to handle every single interrupt separatery then the system
might be significantly overloaded.
Co-authored-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Add new bindings to describe the BELLBOARD peripheral in its two
_programming modes_ local or remote.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
To allow EDMA configuration with the help of the DT_INST_DMAS_*
and DT_DMAS_* macros, all that a consumer node needs to know
is which channel to configure and what MUX value needs to be
used. As such, this commit allows doing this by forcing the
dma-cells property to 2, each cell representing one of the
aforementioned properties.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
To enable per peripheral queue pool sizing options add some bindings to
the i2c controller to setup sq/cq pool sizing.
Its possible this could go away with a shared application pair of pools.
The shared pool would require some added function pointers though to
deal with the variants as the shared pools would need a lock.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Added is_enabled devicetree property to fake regulator.
Allows testing of init behaviour when regulator is enabled
in hardware.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Add devicetree based settings for resolution, axis inversion and sleep
mode enable. Keep the resolution setting in its own function so it can
be called by the application again in runtime if needed.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The nRF91 series devices, when running the Serial LTE Modem (SLM)
application starting with nRF Connect SDK 2.6.0, can now be used as
standalone modems via the generic modem_cellular driver.
A configuration to run the cellular_modem sample on the nRF9160 DK
(plugged in to another nRF91 series device running SLM) is provided.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
