Following dtschema practices, add phyisical units to the shunt resistor
value: milliohms.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The "pmic" driver was in reality a driver for NXP PCA9420 PMIC. There's
no "universal PMIC". While the driver may work for other NXP PMICs, it
is clearly not generic for other vendors PMIC.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Force cache-size to 0 and treat flashdisk as read-only when backing
partition has read-only flag set. This allows users to save RAM when the
application does not write to the flashdisk, e.g. when a predefined FAT
filesystem is used.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Ensure that PECI block is enabled in the EC Subsystem by clearing
the PECI_DIS (peci disable) register
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Following the modification of the STM32 OSPI driver, the clock-names
binding is now required
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
The icmsg backend for ipc_service has a limitation of supporting only
on endpoint. This limitation is acceptable for many IPC instances.
However, some require to use multiple endpoints sharing a single
instance. To preserve the simple and the most efficient single-instance
backend, a separated backend is introduced implementing a wrapper
around icmsg core which adds multiple endpoints support.
There are two multi-endpoint ipc_service icmsg backends: one in the
initiator role, and the other one in the follower role. In a IPC
configuration one end of communication must be in the follower role
while the other one is in the initiator. The initiator initiates
an endpoint discovery handshake to establish enpoint identifiers for
requested endpoint names. The follower responds to requests sent by
the initiator.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
For larger transfers DMA can be used enabling other tasks
to continue running. A threshold of 32 byte transfers
is about right and is defined threshold value for using DMA.
This does not currently support multiple SPI transactions changing
chip select with DMA (though the hardware supports this) currently.
Instead opting for the simpler first change of enabling one shot
DMA SPI transfers for those where the size warrants it.
Adds the loopback binding option to enable the spi_loopback test.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add support input interrupts for GPIO pins on NXP S32Z27
SoC. The driver will convert GPIO pin to respective
interrupt line that will be processed by External
Interrupt Controller.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Add initial support for the NXP S32Z27 SIUL2 External
Interrupt Controller. Each SIUL2 node has a child node
will act as an interrupt-controller that processes external
interrupt signals.
This driver is required to manage GPIO interrupts.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
New ADC driver for the TI CC13xx/CC26xx family.
ADC channel configurations are translated from Zephyr constants to
simplelink driverlib ones (e.g., sample times use a lookup table).
Async mode was also implemented & tested.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Adds Atmel SAMC20 and SAMC21 soc. C series is based on Cortex-M0+.
C21 contains CAN interface.
The init routines are same for SAMC20 and SAMC21. They use one
clock OSC48M without configuration.
The code is inspirated from atmel_sam0/samd21.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
This commit adds an optional property to the nRF21540 Front-End Module
devicetree description that specifies supply voltage in mV. This
property can be used by the nRF21540 driver to compensate the value of
achieved gain for different supply voltage.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Add SparkFun Pro Micro header connector that is implemented by many
other controllers. This allows hardware with compatible headers to
define the related GPIOs and peripherals.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
The ESP32 series MCUs allow to set a timeout which triggers an error
if the SCL line is unchanged for the specified amount of time.
By default, the ESP-IDF HAL sets the timeout to an arbitrary value of
10 times the bus cycle.
This is not sufficient for chips like the TI bq76952, which pulls the
SCL line low (clock stretching) for several 100 µs.
The timeout should also not be dependent on the chosen bitrate, as it
is defined by the time a chip needs for internal calculation before it
can provide requested data or continue communication.
This commit adds a property to devicetree to allow configuration of
the scl timeout. This value is set via direct register access, as the
ESP-IDF HAL does not provide access to the enable bit and does not
give any information about the maximum size of the timeout (defined
in I2C clock cycles in the register).
Fixes#51351
Signed-off-by: Martin Jäger <martin@libre.solar>
Microchip MEC172x has a modified eSPI SAF hardware implementation.
Hardware changes include multiple clock dividers for each SPI
flash device and data transfer using QMSPI local DMA.
espi reset interrupt is made a higer priority in MEC172x devicetree
because espi reset event resets all espi hardware and we don't
to want to service any other espi interrupt blocks when espi reset
occurs.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add bindings to describe a block storage device based on flash map
partition.
Co-authored-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add devicetree binding for the PSA Crypto Random source.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This commit adds missing binding file for the ite,it8xxx2-usbpd.
Without this file, the DT_HAS_*_ENABLED macro wasn't defined and
couldn't be used in the Kconfigs.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
A USB TypeC connector has many peripherals associated with
it and the DTS binding in this commit provides a way to group
peripherals and properties in a device tree.
This binding is used with the USB-C Subsytem.
This is based on Linux, documentation:
https://www.kernel.org/doc/Documentation/devicetree/bindings/connector/usb-connector.yaml
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Add pin control properties to the STM32 UCPD bindings file so that
the pins can be configured in the device tree.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Executing code out of RAM on IT8xxx2 requires that the relevant
addresses be mapped onto the CPU's instruction memory bus, referred to
by ITE documentation as Instruction Local Memory (ILM). ILM mappings
configure blocks of RAM to be used for accesses to chosen addresses when
performing instruction fetch, instead of the memory that would normally
be accessed at that address.
ILM must be used for some chip features (particularly Flash
self-programming, to execute from RAM while writing to Flash), and has
historically been configured in the Flash driver. The RAM for that was
hard-coded as a single 4k block in the linker script. Configuring ILM
in the flash driver is confusing because it is used by other SoC code as
well, currently in code that cannot depend on the Flash being functional
or in hand-selected functions that seem performance-critical.
This change moves ILM configuration to a new driver and dynamically
allocates RAM to ILM in the linker script, allowing software use of the
entire 64k RAM depending on configuration. This makes ILM configuration
more discoverable and makes it much easier to correctly support the
CODE_DATA_RELOCATION feature on this SoC.
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
USB interface that may be used to send messages from a USB host to
the M4 processor in the S3B, and vice-versa.
Signed-off-by: Michal Sieron <msieron@antmicro.com>
Add support for regulator-boot-on to PMIC driver. Many PMIC devices will
be enabled at boot, so this property allows the regulator framework
to correctly track their state.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
As part of a previous refactor, this property was removed from the STM32
USART binding. The driver code to support this feature was not changed.
This commit simply adds the property back to the new base .yaml for
device trees which used it.
Tested on a proprietary board using the STM32U5 on USART1.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
Migrates all Winsen sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all WE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Vishay sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all TI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ST sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Silabs sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Sensirion sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Semtech sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Seeed sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all SBS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Plantower sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Panasonic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all NXP sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nuvoton sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nordic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Microchip sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Measurement Specialties sensors to inherit base sensor
device properties. This will allow us to define properties shared by
multiple sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Maxim sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all LM sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ITE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Intersil sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Invensense sensors to inherit base sensor device
properties. This will allow us to define properties shared by multiple
sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Infineon sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all HOPERF sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Honeywell sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Espressif sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Bosch sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Avago sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Atmel sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Asahi-Kasei sensors to inherit base sensor device
properties. This will allow us to define properties shared by multiple
sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Aosong sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all AMS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ADI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Introduces an initial set of devicetree properties to be inherited by
all sensor devices, similar to how we define a base set of devicetree
properties for I2C and SPI devices. These properties will be used by the
future sensor subsystem to manage and expose sensors to a host operating
system, through HID or another protocol. Additional properties may be
added in the future.
An earlier version of this patch attempted to use the label property
instead of friendly-name, as it was noted during code review as a
possibly legitimate usage of the mostly-deprecated label property.
However, in practice it was difficult to implement because most sensor
bindings also inherit from i2c-device.yaml or spi-device.yaml, and
therefore inherit the deprecated label property from base.yaml. To work
around the deprecation, every sensor binding would have needed to
explicitly block the label property with a property-blocklist, which
would somewhat defeat the purpose of having a shared sensor-device.yaml.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Add MEC172x full duplex qmspi driver version to support full
duplex transfers as expected by the Zephyr spi driver model.
On every spi clock we transmit one bit and receive one bit.
This driver will work with Zephyr SPI NOR driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
updated dts variables naming (hyphen instead of underscore).
moved all properties in microchip ldma yaml to a separate include file,
these properties will be common with the (to be added)
full duplex spi driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Newer ESP32 series MCUs like the ESP32-C3 contain some register changes
incompatible to the original ESP32 and the SJA1000.
The additions in this commit consider these changes and fix the
incompatibilities in the TWAI front-end for the SJA1000 driver.
Signed-off-by: Martin Jäger <martin@libre.solar>
Implement GPIO driver minimal API's for NXP S32 devices, based on SIUL2
peripheral. SIUL2 allows to control the pins electrical characteristics
such as internal pull resistors, pin direction and more.
GPIO driver API's for interrupts will be implemented in a future patch.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
This patch introduces support for NXP S32 LINFlexD peripheral operating
in UART mode. Polling and interrupt-based serial API's are supported.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce Pinctrl driver for SIUL2 module present on NXP S32 devices,
which provides control over all pins, such as function selection and
electrical characteristics that appear on external chip pins.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Add mode selection properties for regulator-pmic compatible. These
mode selection properties will be used with regulators that support
multiple modes, with each mode enabling specific voltage and current
limits.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Refactor binding to use root PMIC IC, so that properties can be shared
between regulator devices. Each individual regulator output is still
created as an individual device, since the regulator API aligns with
these devices better than the PMIC IC itself.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert timer driver to use a light weight syscon and DTS and convert
register information to use offsets and sys_read/sys_write instead of
structs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some windows might need to be set as writtable, so add a flag read-only
to DTS bindings which is set to true for all windows right now. This can
be set to false where needed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Instead of just declaring the memory window register in DTS and have
everything else all over the place (headers, Kconfig, etc.) this change
defines the memory window instances in DTS and uses the device model to
initialize the windows. Code is still part of the SoC, given that we do
not have a driver subsystem suitable for this type of device yet.
Move FW status to own workflow and separate from window setup.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If the flash is used in 4-byte addressing, reading SFDP will fail after
a system reset if the flash isn't power cycled or hardware reset, since
Zephyr will try to use 3-byte addressing while the flash (still) expects
4-byte addressing.
This commit adds the ability to send a reset command to the flash as part
of initialization, which complements the existing reset-gpio
functionality, and is useful on low-pincount flashes which do not have a
hardware reset.
Signed-off-by: Ole Morten Haaland <omh@icsys.no>
Added support for the AMS AS621x series of temperature sensors as a
variant of the TI TMP108 temperature sensor.
Signed-off-by: Jared Baumann <jared.baumann8@t-mobile.com>
Signed-off-by: James Johnson <james.johnson672@t-mobile.com>
Adding ethernet in the DTS file and corresponding binding
for Cyclone V SoC FPGA board..
Signed-off-by: Esteban Valverde <esteban.valverde.vega@intel.com>
Add a fifo address as int value into dmic yaml to separate different
outputs (corresponds to different dais) from the same hw block. Also
change shim address from array to int value.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Replace the hardcoded kPWM_Prescale_Divide_128
driver prescaler with the ones defined in the dtsi file
that allow overriding them by the user.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
This commit adds a driver to simulate GPIO state and interrupts
using the keyboard when using SDL.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Add 2 properties to configure the "any movement" event.
* Ability to disable the interrupt latch
* Select movement mode
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Include files should not have compatible properties set. These do not
represent real hardware and should therefore not appear to do so, e.g.
by appearing in the bindings index as if they were a real hardware
peripheral.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 qmspi. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 adc. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 pwm. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 espi. Update board dts, pinmux and espi driver
files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The FULLDRIVE description on the rt-iocon yaml file was
describing the slew rate and not the FULLDRIVE property.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
When the EXTI Line nb is not set as interrupt by default
(at reset value), the uart instance cannot waekup the
system from its low power stop mode.
The EXTI line must be specified, like with stm32WL55
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a base binding for I3C controllers.
Note that this follows the Linux kernel 5.17 bindings under
Documentation/devicetree/bindings/i3c/i3c.yaml.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a few bits to the devicetree API tests for multi-bus
nodes where a bus can support multiple protocols. This uses
I3C as basis as I3C controller can support both I2C and I3C on
the same bus, while I2C controller cannot support both. So
this needs to make sure the correct bus macros are generated
if appropriate (and not generated if not needed).
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add support to at86rf212[b] sub-giga devices. This work enables use of
pages 0, 2 and 5 in accordance with IEEE-802.15.4/2003/2006/2011. The
proprietary speeds can be object of future work.
Note: It is recommended that user define a power table for better
performance, low emissions and to save power. A reference power table
can be found in the datasheet and should be used for tests only and
not on a final product.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current version of power table is hardcoded in the driver which is a
problem when use devices in production. This change remove all hardcode
from driver and reimplement the feature to allow people create a table
which is defined in devicetree. The big advantage is that each board can
define their own table based on lab tests and allows use of FEM devices
inclusive.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The property is similar to the usb_controller_index_t
enum that is available in the NXP SDK.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This commit introduces the 1-wire master driver for maxim ds2485.
The ds2485 master has nearly the same (1-wire) feature set and
i2c-interface as the ds2477.
Therefore the common parts are extracted, but to avoid
any nda troubles only the ds2485 specific part is included.
Compared to older 1-wire masters, the ds2485 supports higher level
commands, supporting multi byte operations, search next, automatic crc
calculation.
In this driver only basic read and write operations are supported,
further hardware features are not yet utilized by the driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This driver provides an interface to SocketCAN interfaces of the Linux
system running a Zephyr application with the native_posix board. These
interfaces may be virtual or actual CAN buses.
Signed-off-by: Martin Jäger <martin@libre.solar>
Migrate information to DTS and get it from there on the code. Note that
for CAVS 15, the information is not migrated as there's no DTS entry for
it. It can be brought back (in the DTS) if TLB support is enabled for
it.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Add emulator functionality to the serial_test driver, so that it can be
used to simulate a device on the other end of the uart.
If you don't set the buffer-size property in the dts node, there should
be effectively no change from the previous behavior.
Signed-off-by: Jeremy Bettis <jbettis@google.com>
Add the DMA in the DTS binding for OCTOSPI interface
for the stm32 devices from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There are three types GD32 FMC.
GD32 FMC v1: its flash memory has 1 bank, page size is equal in the
bank, flash size is smaller than 512KB.
GD32 FMC v2: its flash memory has 2 banks. Page size equal within the
same bank but different between banks. Flash size can be up to 3072KB.
FMC v2 has two registers to control bank0 and bank1 separately.
GD32 FMC v3: its flash memory has 2 banks, use sector size as the
minimum operating unit, the sector size is not equal.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Define RaspberryPi Pico ADC.
The ADC has internally connected temperature sensor,
Add property to enable this.
The ADC has a single VREF. VCC usually connects to it,
but it may not be in a case.
Add property to make configurable it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Use the clock control API to enable peripheral clocks. Note that both
GPIO and pinctrl drivers are updated at once since they share some IP
blocks.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Use the clock control API to turn on ADC clocks. Note that clock
selection is not yet implemented, so we still rely on custom rcu
properties for that.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This patch adds a clock control driver for GD32 platforms. It is
important to note that the driver is only able to handle peripheral
clocks, but not "system clocks" (e.g. PLL settings, SYS_CK, etc.). On
some similar platforms (STM32) this task is embedded in the same clock
driver, performed at init time but with no options to do any
manipulation at runtime via the API calls. The clock control API as-is
is really orthogonal to "system clocks", and it is arguably a bad idea
to embed system clock init code in a clock control driver. It can be
done at SoC level still using Devicetree as a source of hardware
description/initial configuration.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Remove the CAN_STM32FD_CLOCK_DIVISOR configuration option,
and add configuration via dts property clk-divider instead.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Changes to code:
1. Renamed CAVS_IPC API from common/include/cavs_ipc.h to
common/include/intel_adsp_ipc.h. Renamed all API functions and structs -
added "intel_adsp_" prefix.
2. Moved definitions from intel-ipc-regs.h and ace-ipc-regs.g to SOC
specific headers include/<soc_name>/adsp_ipc_regs.h.
3. Added new common intel_adsp_ipc_devtree.h header with new
macros to retrieve IPC and IDC nodes and register addresses.
Put those new macros in code replacing hardcoded values outside of
devicetree.
4. Changed documentation of IDC and renamed IDC register struct
to have common name between all intel adsp socs.
5. Removed excessive docs description on cAVS IPC protocol.
Changes to Devicetree:
1. Renamed in all CAVS boards .dtsi files content in IPC nodes:
- "cavs_host_ipc" node labels to "adsp_ipc" labels.
- compatible "intel,cavs-host-ipc" renamed to
"intel,adsp-host-ipc".
2. Added (previously missing) yaml file for "intel,adsp-host-ipc"
compatible.
3. Renamed in all CAVS boards .dtsi files content in IDC nodes:
- "idc" node labels to "adsp_idc" labels.
- compatible "intel,cavs-idc" renamed to "intel-adsp-idc"
4. Renamed intel,cavs_idc.yaml file to intel,adsp_idc.yaml
so it is suitable for both CAVS and ACE SoC family.
Moved it from ipm bindings to ipc bindings where it belongs.
Changes to Kconfig:
1. Renamed existing Kconfig option CONFIG_CAVS_IPC to
INTEL_ADSP_IPC.
2. For renamed INTEL_ADSP_IPC addded default value based on
status of the "adsp-ipc" and "adsp-ipc" node.
Signed-off-by: Andrey Borisovich <andrey.borisovich@intel.com>
Convert the device to be Devicetree based. Adjusted tests and other
areas that were using old Kconfig properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some custom refresh profiles need to set the PLL and VDCS
registers. Add them as optional DT properties.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add support for overriding display LUTs in the UC81xx driver. This
makes it possible to use different LUTs for the full and partial
refresh profiles.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add a separate profile for partial refreshes. This makes it possible
to specify a separate refresh configuration for partial and full
refreshes.
The driver now transitions to full refresh mode when blanking is
turned on. It transitions back to partial refresh mode when there is a
write while blanking is off.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Introduce the concept of refresh profiles which are specified as a
child node in the device tree. This makes it possible to use different
overrides for different types of refreshes (full/partial).
The only profile that is currently supported is the "full" profile.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
This patch is to add Cadence QSPI NOR flash device tree element
for the Cadence QSPI NOR flash driver bringup
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
This adds flash driver for Renesas SmartBond(tm) family.
This technically uses QSPI controller but since default and most
commonly used configuration is to boot from external QSPI flash (DA1469x
do not have built-in flash) and that flash is mapped into memory space,
it can be represented as internal flash.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds serial driver for Renesas SmartBond(tm) family. Both polling
and interrupt APIs are supported.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds GPIO driver for Renesas SmartBond(tm) family.
Driver supports pin configuration (input/output) and interrupts on edge.
Interrupts on level are not supported by hardware.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Add a new reset driver for GD32 platforms. This driver controls the
reset registers from the RCU peripheral. It can be used to restore
peripherals to their initial state when initializing a device.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
It was not possible to disconnect a pin using the nRF pinctrl driver.
That is, it was not possible to set PSEL to 0xFFFFFFFF (indicating pin
is not connected). This can be useful in certain scenarios, e.g. a
bootloader configures all signals of a certain peripheral but
application then needs to disconnect certain signals.
A new DT macro has been introduced to accomplish this:
NRF_PSEL_DISCONNECT. It can be used like this to explicitely disconnect
a peripheral signal:
```
&pinctrl {
uart0_default: uart0_default {
group1 {
psels = <NRF_PSEL(UART_TX, 0, 1)>,
<NRF_PSEL_DISCONNECTED(UART_RX)>;
};
};
};
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Despite being used in GD32 dts files, the compatible did not exist. Note
that there is no GD32 flash driver yet.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The TS_CAL values for the temperature sensor are measured on 12, 14 and
16 bit resolution depends on the STM32 series. Because the drivers
operates at 12 bit resolution the TS_CAL1 and TS_CAL2 must be divided.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
This commit defines a new dma version for devices like stm32U5.
The peripheral is a GPDMA in this soc serie.
It has several specific definitions used by its stm32 LL driver
compared to the V2, including up to 16 channels.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There are 3 bindings for STM32 serial driver:
st,stm32-uart.yaml
st,stm32-usart.yaml
st,stm32-lpuart.yaml
Add a common st,stm32-uart-base.yaml that would be included by these
3 bindings an would group common properties.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
This commit adds string token versions of the values also
in items inside string-array.
Signed-off-by: Radosław Koppel <r.koppel@k-el.com>
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Co-authored-by: Kumar Gala <galak@kernel.org>
Add missing support for the triggered mode using GPIO
interrupt alert pin. It uses mode detection at runtime
which allows working multiple sensors with different
modes simultaneously.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
The new property nist-config is introduced to the stm32 mcus
to configure the RNG for NIST SP800-90B certification.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The gpio-leds binding is meant for LED drivers, not GPIO. As in Linux,
move the binding to the led folder.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
gpio-keys binding has been used in Zephyr to describe random push
buttons in boards. On Linux, it is used by a keyboard input driver,
while in Zephyr is, in most cases, used directly in applications out of
the device driver model. This should likely be _fixed_ if one day we
have a proper input device class. Still, we can align a few things:
- Inherit from base.yaml (we need status, compatible, etc defined there)
- Remove the requirement of a label in child nodes
- Fix child nodes label description
- Move to dts/bindings/input
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Don't import the label prop from base.yaml as it is marked deprecated.
This lets the various tests that still use DT_LABEL() to work properly.
Signed-off-by: Kumar Gala <galak@kernel.org>
Mark 'label' property as deprecated in base.yaml. 'label' is still
defined and valid for specific bindings to specify like gpio-keys.yaml
or fixed-partitions.yaml.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add spi0 and spi1 configuration to rp2040.
spi0 and spi1 are declared as compatible with
"raspberrypi,pico-spi" and "arm,pl022".
"raspberrypi,pico-spi" is just inherited from
"arm,pl022" and "reset-device"
spi0 and spi1 declare as compatible with "raspberrypi,pico-spi"
and "arm,pl022".
"raspberrypi,pico-spi" is just inheriting "arm,pl022" and
"reset-device" for declaring the 'reset' property,
with no additional property and implementation.
Add also pinctrl macros to dt-bindings header.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add fundamental feature support for PL022 SPI peripheral.
This commit implements synchronous transfer with 8bit-MSB format.
Optional functions are not currently implemented yet.
- interrupt based transfer is not implemented yet.
- DMA transfer is not implemented yet.
- Slave mode is not implemented yet.
- Currently support only 8-bit data transfer.
Hardware limitation:
- LSB-first format is not supported by hardware.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
The binding 'nxp,lpc-iap' is no longer used, which is confirmed
by running:
$ find ${ZEPHYR_BASE}/dts/arm/nxp -type f | egrep -e '\.dts(i)*$' | \
xargs grep -nH nxp,lpc-iap
Changes in this commit:
- remove DT_HAS_NXP_LPC... in drivers/flash/Kconfig.mcux
- remove schema file for nxp,lpc-iap
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
The binding 'nxp,iap-lpc' is used for different flash controllers,
preventing clarity. This commit introduces bindings for each version of
the flash controller, as they appear with NXP lpc device families:
nxp,iap-fmc11: for the flash controler used on the lpc11u6x family
nxp,iap-fmc54: for the flash controler used on the lpc54xx family
nxp,iap-fmc55: for the flash controler used on the lpc55xx family,
except lpc553x
nxp,iap-fmc553: for the flash controler used on the lpc553x family
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
The SSD16xx driver currently hard-codes a couple of register overrides
that aren't relevant or even correct for many devices. Make them
optional device tree properties instead.
Note that this changes the behavior for panels that expect
SSD16XX_CMD_DUMMY_LINE and SSD16XX_CMD_GATE_LINE_WIDTH to be set by
the driver. This fixes a bug where the incorrect value
was written to all SSD16xx panels except for GDEH0213B1 and GDEH029A1.
The overlay files for devices that need dummy line and gate line width
to be specified have been updated as a part of this commit.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The OTP in most SSD16xx-based displays normally contain default
VCOM/GDV/SDV values. Make all of these optional in the device tree.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add the option to specify the minimum duration that the `reset-gpios`
pin is held low on boot. This lets devices with additional capacitance
on the reset line still reboot the Bluetooth controller.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This fixes underrun issues when hardware flow control can't be used.
Only tested on STM32F4.
Signed-off-by: John Kjellberg <kjellberg.john@gmail.com>
...
All the of the ITE it8xxx2 devicetree compatiables are of the form
ite,it8xxx2-<DEV>. However the PECI device was ite,peci-it8xxx2,
rename the compatiable to match the pattern used everywhere else.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add dts bindings for the NIOS2 QSPI controller and flash device and
add nodes to the dts files for these devices as well.
Signed-off-by: Kumar Gala <galak@kernel.org>
Fat finger mis-typed when I renamed the file last time.
So correctly name the file this time. Hopefully this is
correct and won't need anymore renaming... :(
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The current atmel sam flash driver was develop based on the cortex-m7
version of smart arm microcontroller. The driver support write
protection and cache functions which is not supported by other cortex-m
variants. This fixes current driver implementation and devicetree
entries for all sam variants.
Notes:
* The cortex-m3 doesn't have support erase pages flash command and
because of that the driver still not not compatible. Keep it disabled
until a patch be send. The hwinfo driver is not affected by this
restriction.
* The sam4l variation requires a specific driver because uses another
flash controller (flashcalw). Added another compatible to
differentiate and keeped node disabled until a driver be available.
Fixes#48516
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
() Fix the compatible string from "intel,dai,dmic" to
"intel,dai-dmic".
() Also rename the yaml file to have vendor name first.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use a test compatible so that test can create a DT-based device and
provide a valid choice when building the test.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to work on a clock speed higher than 20 MHz, IO MUX is required.
Co-authored-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Signed-off-by: XiNGRZ Chan <hi@xingrz.me>
various microchip bindings set 'girq-cells' and 'pcr-cells'
sections in the bindings. However the bindings where for the
client nodes and thus do not need to set these.
Signed-off-by: Kumar Gala <galak@kernel.org>
Change the wording about "alternate/optional" clock to "domain" clocks,
to better describe the feature and minimize confusion.
Additionally, provide more description about domain clocks and dual
domain functionality implemented in peripherals.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds optional device tree property to specify a default character
to clock out when the TX buffer pointer is NULL. If the property is
not set the existing behavior (default char of 0x00) is used.
I verified the expected behavior using an i.MX RT685 board and
logic analyzer that the def-char character is transmitted when
TX buffer pointer is NULL.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
LPC55s3x family has an additional analog mode bit available. Update
IOCON binding and IOCON driver to support setting this bit via a pin
control property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use Devicetree to describe the UART UPIPE IEEE 802.15.4 driver. This
allows to remove usage of IEEE802154_UPIPE_DRV_NAME in preparation for
the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_NRF5_DRV_NAME in preparation for the
removal of NET_CONFIG_IEEE802154_DEV_NAME.
All SoC files have been updated with the addition of an ieee802154 node
(disabled and only on those SoCs that define ieee802154-supported. The
peripheral has been enabled in the nRF52840DK board (used for testing
ieee802154).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_KW41Z_DRV_NAME in preparation for the removal
of NET_CONFIG_IEEE802154_DEV_NAME.
KW41Z files have been updated with the addition of radio and an
ieee802154 nodes The peripheral has been enabled in the frdm_k41z board
(used for testing ieee802154).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC13XX_CC26XX_SUBG_DRV_NAME in preparation
for the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC13XX_CC26XX_DRV_NAME in preparation for the
removal of NET_CONFIG_IEEE802154_DEV_NAME. All boards used in testing
have been updated to enable the peripheral in DT as well.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
ICI (Inter-Core Interrupt Unit) interrupts and priorities were hardcoded
in C files. This patch moves this information to Devicetree and updates
code to make use of it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
sysconf base address was hardcoded in <soc.h>. Create a new compatible
and define it in Devicetree, where hardware needs to be described.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce a simple binding for atmel,24mac402 EEPROM that the SAM
GMAC ethernet driver can utilize to get MAC address out of. We
introduce a 'mac-eeprom' phandle into GMAC ethernet devicetree
node that will provide a pointer to the MAC eeprom to utilize.
Signed-off-by: Kumar Gala <galak@kernel.org>
The CLINT (Core Local Interruptor) description was not aligned with
Linux. For example, there's no "riscv,clint0", but "sifive,clint0". The
peripheral is not described as an interrupt-controller either.
Ref. https://elixir.bootlin.com/linux/v5.18.14/source/arch/riscv/boot/
dts/starfive/jh7100.dtsi#L106
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
After some analysis I found out that there's no machine timer provided
by the "riscv" vendor. There are some specs for the mtime/mtimecmp
registers (this is why we can have a single driver), but the actual
register layout or implementations differ amongst vendors. GD32 uses the
Nuclei implementation, named "system timer" in their documentation. This
patch aligns with vendor specs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This adds a driver for Maxims DS2484 Single-Channel 1-Wire master
driver. The DS2484 features an extra pin to enable sleep modes which
is available if the pin is configured in the device tree.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Unlike stated in 57df225b396e43358aac4cc998ed2e99fdb57780, RM0456.pdf
reference manual mentions about PLL1R that "Only division by 1 and even
division factors are allowed."
Though, in reference manual, there is one issue on PLL1R values
description, which should actually be:
0000000: pll1_r_ck = vco1_ck
0000001: pll1_r_ck = vco1_ck / 2 (default after reset)
0000010: Not allowed
0000011: pll1_r_ck = vco1_ck / 4
...
This description will be fixed.
Reflect this in binding and driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of enabling WOVCRO clock based on the SOC, use a configuration
to indicate support, so that each platform can specify if WOVCRO is
supported or not.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Add binding for Aspeed AST10x0 clock driver. The clocks can be turned
on or off through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The UC8176 and UC8179 chips that exist in tree have subtly different
register layouts. Use separate compatible strings for these chips and
a quirks structure that describe device-specific behavior.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The GD7965 driver is really just a vendor name for the UltraChip
UC8179. Rename the driver to UC81xx since there are other chips in the
family (e.g., the UC8176) with an almost identical register interface.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
For the !SOC_I2C_SUPPORT_HW_CLR_BUS in which we implement bus
reset via GPIOs, change the devicetree properties to be actual
gpio properties and update the code to reflect this.
Signed-off-by: Kumar Gala <galak@kernel.org>
This commit adds the pll2 and pll3 clock control nodes
with st,stm32u5-pll-clock compatible.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit changes the range for stm32u5 pll divider values
to allow divider value of 1.
- DIVQ is allowed to beconfigured 1 for all PLL instances
- DIVR can be 1 for PLL2 and PLL3, but is not valid for PLl1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
We have drivers for "nxp,lpc-rtc" and "zephyr,native-posix-counter"
devicetree compatibles, however we had no bindings for them. Add
simple bindings
Signed-off-by: Kumar Gala <galak@kernel.org>
Two files ending with yml while the rest is ending with yaml, just
rename those two to avoid special handling.
Fixes documentation build.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL adds a DT node, 'power_leakage_io', which property,
'leak-gpios', contains GPIOs that have leakage current. In oerder to get
better power consumption, npcx power driver will disable the connections
between these io pads and input buffers before entering deep sleep.
Then, restore the connections after ec wakes up.
The users can overwrite this property at board DT file. Here is an
example:
&power_leakage_io {
leak-gpios = <&gpio0 0 0
&gpiob 1 0>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL configures low-voltage (1.8V) detection via GPIO driver with
GPIO_VOLTAGE_1P8 flag. It also adds support for this flag in
pin_get_config() function.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Cleanup npcx low-voltage (1.8V) detection configuration. It removes
unused soc utilities, macros, and DT node. We will configure this
feature by GPIO driver with GPIO_VOLTAGE_1P8 flag later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Devicetree is the natural place to describe hardware, so move the
maximum frequency the SPI can work with to Devicetree instead of relying
on values from HAL.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some panels using this driver don't provide tcon/cdi/pwr/softstart
values in their reference code. It is normally expected that the right
values will be loaded from OTP in such cases. Make these values
optional to support such panels.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add configuration for SPI connected ADXL345 accelarator sensor
as adi,adxl345-spi.yaml.
Rename original adi,adxl345.yaml that configured for I2C
rename to adi,adxl345-i2c.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Implement support for SAML21 parts, tested on a SAML21 Xplained Pro dev
board. Confirmed operational peripherals: UART, GPIO, PWM, ADC.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Remove 'label' property from SDHC nodes. We can use variants of
DEVICE_DT_GET to get access to a device pointer for use in an
application.
Signed-off-by: Kumar Gala <galak@kernel.org>
The 'nxp,imx-flexspi-device' compatible that was specified in
the YAML file is not an actual compatible that is intented to be
used. Instead the YAML file is included in other YAML files
that set specific compatible.
If the 'nxp,imx-flexspi-device' was used we'd actually get an error
from edtlib because of having the same compatible specified by
two different YAML files.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Clean up unused psl functions in scfg.c, unused DT macros, unused psl DT
nodes and related yaml files. Currently, PSL pad configurations are made
by pinctrl mechanism. Please refer
https://issuetracker.google.com/234861079 for more detail.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
HDA is a common IP used across the entire ADSP line and deserves
a name respecting that alongside similiar IP drivers such as the
ADSP GPDMA driver.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add adsp-imr binding. This memory type is being used in intel adsp dts
but this binding was missing.
Co-authored-by: Marcin Szkudlinski <marcin.szkudlinski@intel.com>
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
All in tree device drivers on a bus use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add simple clock control node in devicetree for beetle to handle
relationship between drivers (uart, timers, gpio) and clock controller
device.
Signed-off-by: Kumar Gala <galak@kernel.org>
Use DT_INST_FOREACH_STATUS_OKAY to reduce duplicated code for each
instance.
We make interrupts optional since they aren't always available.
Signed-off-by: Kumar Gala <galak@kernel.org>
Replace sensor_label property in devicetree with just a sensor phandle
property. This is more generic and allows driver to use DEVICE_DT_GET
instead of device_get_binding.
Signed-off-by: Kumar Gala <galak@kernel.org>
- adds properties 'group', 'index' and 'prescaler'.
- updates board's dts to include those properties.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Clean up unused pinmux function 'npcx_pinctrl_mux_configure()' and
related 'NPCX_DT_IO_ALT*' macro functions.
Please refer https://issuetracker.google.com/234861079 for more detail.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Switch from using a driver-specific, compile-time devicetree one-shot
property to supporting the newly added CAN_MODE_ONE_SHOT flag for
enabling/disabling one-shot mode at run-time.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove the support for enabling passthrough mode support for MPU9150
on the AK8975. We don't have a proper MPU9150 driver and the MPU9150
has been EOL. So its highly unlikely this code is being used.
Additonally we remove the device tree binding for the MPU9150 since
we don't have a proper driver for it.
Signed-off-by: Kumar Gala <galak@kernel.org>
CONFIG_SIFIVE_SPI_0_ROM (default y) was an option to disable spi0 if
used to access SPI Flash ROM. However, its design had a problem: it
relied on instance numbers. You had to set status okay for spi0 to make
it work (incongruent with the purpose of the option itself). This patch
makes things simpler: if such SPI0 is not available, simply keep it
disabled in DT. Bindings have been updated to mention this case.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
cAVS and ACE gpdma driver have several similarities. This commit merge
this two drivers into a single one for Intel ADSP devices.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add NPCX Power Switch Logic (PSL) DT node which controls the power rails
of SoC to get better power consumption.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces how to configure PSL (Power Switch Logic) pads
properties such as input detection mode/polarity, pin-muxing and so
on via pinctrl mechanism. It includes:
1. Add two pinctrl properties and their enums for PSL input
detection configuration.
psl-in-mode:
- "level"
- "mode"
psl-in-pole:
- "low-falling"
- "high-rising"
2. Add macro functions to get PSL input detection and pin-muxing
configurations from 'pinmux', 'psl-offset' abd 'psl-polarity'
properties.
Here is an example to configure PSL_IN2 as the PSL detection input and
its mode and polarity.
/* A falling edge detection type for PSL_IN2 */
&psl_in2_gp00 {
psl-in-mode = "edge";
psl-in-pol = "low-falling";
};
A device will be introduced later which uses this pinctrl node to
configure PSL input detection settings and how to turn off VCC1 power
rail by PSL_OUT.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This peripheral combines a hardware-based USB CDC ACM serial interface
and a JTAG interface.
It is present in the ESP32-C3.
Signed-off-by: Martin Jäger <martin@libre.solar>
This will add ace compatible DMA driver.
Co-authored-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds basic support for the watchdog timer on the RP2040 MCU and
Raspberry Pi Pico development board
Signed-off-by: Jamie McCrae <spam@helper3000.net>
This commit adds support for the ds18b20 1-wire temperature sensor.
The sampling resolution of the sensor can be set in DT.
In case only a single device is on the bus, the driver issues
skip_rom commands. However, in case DT defines several devices,
the driver will use match_rom commands and therefore it is necessary
to set the rom_id of the device via the sensor attribute interface before
being able to sample sensor values.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The zephyr-serial w1 driver introduced in this commit implements
all routines for the w1 api on top of the zephyr serial driver.
W1 bit read, write, and reset operations are executed by issuing
polling zephyr serial byte read and write operations.
The driver should be usable on most platforms in zephyr that have
implemented support for the polling procedures of the serial driver.
As not all serial drivers are implemented exactly the same minor
additional quirks may be needed on some platforms.
The most notable difference of polling serial driver implementations
seems to be that some return immediately from poll_out after the
transmission was started(e.g. STM32) and others wait until
the transmission was completed before returning from poll_out
(e.g. NRF). While this has influence on the timeout, both types
are supported by this driver because the driver waits for a
configurable time period until it terminates the read.
The driver needs an appropriate open drain interface to be able
to communicate with slaves.
In the simpliest case this might be achived by configuring the mcu pins
in open-drain configuration with a (sufficiently small) pull-up to 3V3/5V.
Otherwise an external circuit needs to provide this interface.
Overdrive and Standard Speed modes are supported by this driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit introduces a new api for the Dallas 1-wire protocol.
The api includes link functions for read and write operations on
bit, byte, and block level, as well as functions to reset and
lock the bus.
The bus configuration is derived from the device tree and can be
queried using w1_slave_count routine.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The default S0S1 drive setting is not suitable for TWI/TWIM pins.
Override it with S0D1 as for some SoCs (e.g. nRF52833) without
this the peripheral will not work properly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There is no driver or other references to the zephyr,ipm-console
devicetree compatiable. So remove the binding.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add binding for zephyr sdmmc disk device, which uses the SD
subsystem to manage an SD memory card.
Fixes#46410Fixes#46266
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a stm32h7 spi compatible.
This compatible intends to match all SPI hardware blocks that
can be compatible with the one available in stm32h7 devices,
for instance, but not limited to stm32u5 and stm32mp1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use consistent name for SPI HW block property so applications
using a device tree overlay work transparently.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Add MKR header connector that is implemented by Arduino MKR series.
This allows hardware with compatible headers to define the related GPIOs.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Some EFR32 SoCs use a secure element subsystem to manage
security features (i.e., TRNG, secure bootloader or cryptographic
functions).
This driver relies on the SE Manager high-level API provided by Silicon
Labs. The API interacts with the SE subsystem, provides helper functions
to achieve cryptographic operations and ensures that only one operation
is running at a time by using mutexes and semaphores.
Instead of relying on the SE Manager from Silicon Labs, one could
recreate the behaviour of the Manager and put the code in the crypto
driver folder and create a dependency for other drivers using the crypto
manager (e.g., keys, entropy).
I went for the SE Manager API as it is already there and supported by
Silicon Labs.
Tested using the random subsystem.
Signed-off-by: Steven Lemaire <steven.lemaire@zii.aero>
Add the stm32g0 bindings for the HSISYS to be used with the hsi divisor
with a factor programmable from 1 to 128.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
According to the formulas found in the reference manuals of the SoC
families using the "st,stm32-temp-cal" version of the temperature sensor
(i.e. G0, G4, H7, L0, L1, L4, L5, U5, WB, WL), the temperature is
computed with the following formula:
T = ((TS_CAL2_TEMP - TS_CAL1_TEMP) / (TS_CAL2 - TS_CAL1))
* (TS_DATA - TS_CAL1) + TS_CAL1_TEMP
What is called ts-cal-offset in the stm32_temp driver is therefore the
same value as TS_CAL1_TEMP1. Use it directly instead of defining another
property.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The stm32_temp driver defines the ts-voltage-mv property to determine
the reference voltage of the ADC in the temperature computation. However
this information is already available in the device tree at the ADC
level (even with the same default value). Use it through the ADC API
instead of duplicating the information.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This new DTS Node is defining a ratio for Vbat internal
bridge of monitoring sensor connected
to a ADC internal channel. The voltage reference value
is given by the ADC of the stm32.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Like other temperature or vrefint sensor, the stm32 mcu
also have a Vbat monitoring internal channels on ADC.
Add this entry to the device tree.
The vref is usually 3300mV present on the target board.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
-pin properties, e.g. tx-pin have been replaced by pinctrl. Mark them as
deprecated since old pin configuration schemes will be deprecated in
Zephyr 3.2.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit moves the hardware configuration for ledc
peripheral to the device-tree instead of Kconfig.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Enable pin control support for SWO log backend, by creating a new
ITM node for the ARM instrumentation trace macrocell. Add pin control
properties under this node, and refactor the swo-req-freq property to be
defined within this node.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit rewrite renesas R-Car clock driver in order
to be able to support any new SoC easier.
This work is so creating a clock driver per soc alongside a
common driver for all reneasas r-car boars.
- drivers: create a driver per soc
- create a common driver
- create a common header used by soc & common driver
- create a soc specific driver calling for common driver
- dts: use new compatible
- use old yaml as common yaml
- create a new "child" yaml to define the new compatible field
- change compatible in device tree
As in Linux, the driver can support both r8a77951 and r8a77950
SoC's so we decided to name the new driver as in Linux with Zephyr
prefix : "clock_control_r8a7795_cpg_mssr.c".
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Panasonic's reduced Arduino header is based on the Arduino UNO layout.
The main difference is that some pins are not available due to the
lack of pins on the Panasonic module.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
Bindings for Intel HDA now require the buffer alignment property to be
set.
Sets the property to 128 bytes for the common Intel cAVS device tree as
was implied by the tests cases.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Enable statically allocated buffers to determine their buffer alignment
with a device tree property rather than having to find out through docs.
Should save people lots of time.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add I2C bus recovery support to the NXP MCUX LPI2C driver. Since the LPI2C
peripheral block does not natively support I2C bus recovery, recovery is
performed using GPIO bitbanging.
Fixes: #42574
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The armv8 timer, arm gic, and arm gic-v3-its don't use or need the
devicetree label property. Update the dts bindings to not require it and
remove setting of the label property in dts files.
Signed-off-by: Kumar Gala <galak@kernel.org>
In 8f9290d2741844 ('dts: bindings: riscv: Add and use bindings for
sifive CPUs'), new compat strings for SiFive CPUs were added, but with
riscv prefixes. Vendor-specific compats should just be prefixed with the
vendor, so move that over here.
Fixes: 8f9290d2741844 ('dts: bindings: riscv: Add and use bindings
for sifive CPUs')
Signed-off-by: Olof Johansson <olof@lixom.net>
G4 and U5 series missed clock information in DT. Driver likely worked
because it was using HAL helpers, bypassing the purpose of DT and clock
control drivers. The clocks property is now required in the binding
file.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Adds `four-byte-opcodes` property. When set, then used write and read
opcodes will be converted to 4-Byte opcode.
Doesn't convert erase opcodes yet.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds write opcode (`writeoc`) property. That allows to provide
custom write opcode in the DTS.
Doesn't support OPI mode.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The driver supported getting register shift from Devicetree, from a
custom definition in SoC headers (fragile) or, it took a default value.
This change simplifies things by making reg-shift property required in
all instances.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The reserved memory mechanism (sections and regions definition) has been
entirely replaced, greatly extended and made it better by the work done
on the zephyr,memory-region compatible.
Since there is are no actual users, we can remove it.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This reverts commit 7f51907fda.
The problem with setting the priority at the highest priority possible
is that when the IPC is under high traffic, the WQ could starve the
scheduler.
Move back to a more sane preemptive priority as default value.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This includes DTS bindings for the Texas Instruments CC13xx/CC26xx flash
controller driver and adds support for it in CC1352R and CC2652R SoCs
DTS files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Recently OpenAMP introduced the possibility to set the sizes for TX and
RX buffers per created instance. Expose this also to Zephyr users by
using a DT property "zephyr,buffer-size".
For the sake of simplicity use the same DT property to set the buffer
size for both TX and RX buffers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Extends #43119 with PPB and IO values of
`memory-region-mpu`.
That allows MPU region definition with
PPB or IO attributes in the DTS.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
This patch adds DTS properties for using wake-up mode
and the autosleep function to the ADXL362 driver.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Add a pseudo device diver with device tree bindings for coredump.
The device tree bindings exposes memory address/size values to be
included in any dump. And the driver exposes an API to add/remove
dump memory regions at runtime.
Signed-off-by: Mark Holden <mholden@fb.com>
This commit aligns SPIM shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
This commit aligns UARTE shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Since the introduction of the `zephyr,memory-region` compatible
to create new memory region, drivers can now use the newly defined
region in the DT by using the macro LINKER_DT_NODE_REGION_NAME()
on the node_id to retrieve the region name and possibly allocated data
or variables in that region (or for whatever other use).
This is assuming though that the driver knows in advance the node_id to
reference.
A better approach is to add a new generic 'memory-region' property
that can be used by any driver to reference a region by using a phandle,
so that the driver can use that to retrieve the memory-region of interest.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The ALH is an intermediary device, which acts as a hub and provides an
abstracted support for numerous sound interfaces (e.g. SoundWire).
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
This sensor is virtually identical to the lsm6dso. The only difference
is the accelerometer ranges are double those of the lsm6dso.
Use the same driver. The difference is detected by using "st,lsm6dso32"
as the first compatible entry, followed by "st,lsm6dso".
An bit flag in the existing accel_range config field is used to check if
the chip is the doubled range or not.
Signed-off-by: Trent Piepho <trent.piepho@igorinstitute.com>
Config pwm open-drain mode without enabling STORE_REG. This CL
collects all active PWM's base address and related index in an
array. Then, pinctrl driver configs its open-drain mode by
finding the corresponding 'channel' index.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Pinmux is depricated (see #39740) and shouldn't be used anymore
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Extend the common ADC controller binding with a child binding that
allows specifying configuration of ADC channels.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add 'inversion-on' property to st7735r.
Issue INVON(21h) command on initializing if inversion-on was enabled.
As a result of this command, the display color is inverted.
Otherwise, INVOFF(20h) will be issued.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add pin control support for IOMUXC peripheral present
on mimx8ml8_m7 soc. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a
new header and compatible binding to handle the
different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for IOMUXC peripheral present
on mimx8mq6_m4 soc. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a
new header and compatible binding to handle the
different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for mcimx7_m4 SOC. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a new header and
compatible binding to handle the different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add the DTS binding for OCTOSPI interface for the stm32 devices
from STMicroelectronics.
This corresponds to a NOR octo SPI flash.
In this config, there is only on NOR-flash device.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx eSPI and host_subs driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx adc driver. Please notice users need to
configure the corresponding pinctrl nodes in 'pinctrl-0' property in the
adc0 DT node. For example, if ADC0 and ADC2 channels are selected for
the application, please add the follwoings in your board DT layout file.
&adc0 {
status = "okay";
/* Use adc0 channel 0 and 2 for 'adc_api' driver tests */
pinctrl-0 = <&adc0_chan0_gp45
&adc0_chan2_gp43>;
pinctrl-names = "default";
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx tachometer driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in ps2 driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in pwm driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in i2c driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in uart driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL is the initial version for npcx pinctrl driver and introduces
pinctrl nodes for both IO-pads and peripheral devices for each npcx
series. Users can set pin configuration via these nodes in the board
layout DT file. It also wraps all configurations related to pin-muxing
in pinctrl_soc.h. Regarding the other pin properties, we will implement
them later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The drive-mode property is nRF specific, so prefix it with `nordic,`,
same as the `nordic,invert` property.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Enable pin control for lpc11u6x i2c driver, and remove pinmux usage from
board level DTS files.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
convert lpc11u6x syscon clock driver to pin control, and remove all
pinmux usage from driver and syscon dts node.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update pin control driver for lpc11u6x. This SOC does not have a HAL,
so fsl_clock is not available. It also lacks a slew-rate field in the
IOCON register, so this property must be optional.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
switch gpio driver to use pio nodes to configure pin control settings,
and stop using pinmux driver within gpio driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Since implementation of clock source selection in consumer device drivers
could be achieved without usage of a clock-names property and no
example of usage is provided up to now, remove this property from existing
examples.
Additionally, make it clear in stm32 clock control binding that it is
driver's responsibility to correctly access clock source information
and use it as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add STM32 clock mux binding.
Only property of a node using such compatible is to
select a clock input.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the UPLLCK clock for the CAN controller as recommended by the Atmel SAM
E70 data sheet.
Move the configuration of the clock prescaler from Kconfig to devicetree
and limit it to the values recommended by the SAM E70 datasheet.
Fixes: #45012
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add DTS binding for Motorola MC146818 compatible Real Time Clock.
This is being used for the RTC/CMOS timer on x86 PC-compatible
platforms.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add optional PINCTRL support to the Microchip XEC PS2 driver
shared between MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Comparator will monitor signal though ADC channel, based on
user configuration, callback will be triggered.
This will enable comparator functionality for nuvoton MCU utilizing its
ADC threshold detection feature. Implementation is exported through
sensor trigger API. Use of CONFIG_ADC_CMP_NPCX is required.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
remove existing SDMMC SPI driver, since it is replaced by the SPI mode
SD host controller driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
with the legacy USDHC driver fully removed from the tree, the
nxp,imx-usdhc binding can now be used for the new SD host controller
driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
all in tree SOCs with the USDHC peripheral have now been converted to
use the new SD host controller USDHC driver, so remove legacy NXP disk
USDHC driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add SDHC driver implementing spi mode support for SD cards. This driver
implements the standard SD host controller APIs, and sets the host
property "is_spi" to indicate to the SD subsystem the card will be
running in SPI mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add generic SDHC dts binding, as well as DTS binding for NXP USDHC.
Update iMX.RT DTS binding to use USDHC compatible
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Make the LSE driving capability configurable for the STM32 series.
Fixes#44737.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Fix the descriptions for the ST STM32 FDCAN devicetree bindings. These
are derivates of the Bosch M_CAN, but they target specific SoC
implementations.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the base Bosch M_CAN CAN-FD controller devicetree binding to
match the product name and the upstream Linux devicetree binding.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fold the simple bosch,m-can devicetree binding into the front-end
devicetree bindings. The bosch,m-can compatible is not used in Zephyr.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
MCP4728 is a 12-bit, Quad Digital-to-Analog Converter with EEPROM Memory.
Controlled via I2C interface.
Signed-off-by: Marek Janus <marek.janus@grinn-global.com>
In 92d8329d5b a new DT property was introduced to set the WQ priority
of the instance. The fallback value when the property was not present
was arbitrarily set to <0 PRIO_PREEMPT>.
The problem is that this value is actually changing the behaviour for
the code that is not explicitly setting the DT property, breaking in
some cases the existing code.
Move the default value to <0 PRIO_COOP> to give the old code a
consistent behaviour before and after the 92d8329d5b commit.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This is a follow-up to commit 1a01ca2adf.
Since support for pinctrl has been added to the qdec_nrfx driver,
the related binding can no longer require the `a-pin` and `b-pin`
properties to be defined.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add DT option to configure the data ready interrupt mode.
Latched is the default; pulsed can be enabled through
the drdy-pulsed DT, if desired.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Add FDS (Filtered Data Type Selection) + High-Pass reference mode support
(FDS in CTRL6, HP_REF_MODE in CTRL7)
Values are configurable through DT per instance.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
The PWM period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The binding has no corresponding driver and it is not referenced
anywhere, so drop it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The binding did not define the PWM cells. Only channel and period have
been added as they are the minimum required ones (flags are not supported).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds it. Note that flags have not been added as they are
optional and not supported anyway.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce has-interrupt-mask-reg DTS property for nxp,pca95xx driver.
This additionnal property allow to specify that the gpio expander has an
interrupt mask register that must be configured by the driver.
This allow to use this driver with PCAL95xx.
This fixes issue #44834.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
NXP LPUART IP supports loopback mode, where TX is internally connected
to RX input. Allow setting loopback mode up via the "nxp,loopback" dts
property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Align the board dts with the recent changes in the "nordic,nrf-sw-pwm"
binding (remove the no longer existing `channel-count` property) and
add a node representing the edge connector for convenient referring
to SoC pins connected to it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... to align with what is used in most other PWM bindings.
Update PWM nodes in SoC .dtsi files accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Align with other PWM drivers and treat the `pwm` parameter (described
ambiguously as "PWM pin") of the `pwm_pin_set_cycles` function as a PWM
channel, not an SoC pin. This will also make the driver consistent with
the `pwm-cells` property definition in the "nordic,nrf-sw-pwm" binding
and with related `DT_PWMS_*` macros.
The change described above requires also providing a way to specify
SoC pins that are to be assigned to the PWM channels. Hence, the commit
introduces in the "nordic,nrf-sw-pwm" binding the `channel-gpios`
property that replaces the `channel-count` one.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rework bindings documentation to clearly illustrate the role of ahb
(and cpu1) prescaler which defines the actual core clock frequency,
and not only a bus frequency.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use enum to describe the range of allowed MSI values.
This will help to detect configuration issues earlier.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On some parts, it could be required to use steps before applying
highest frequencies.
This was previously done as part of LL_PLL_ConfigSystemClock_FOO
utility functions which are no more used.
Use device tree to mention when this is required and implement it
in stm32_clock_control_init().
Additionally, fix the calls tp LL_RCC_SetAHBPrescaler, which require
use of ahb_prescaler helper.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
those bindings are no more needed since pinmux was
deprecated in favor of pinctrl.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
After pinctrl's subsystem support, I2C pin properties are
no longer required for pin muxing, however, this information
is still valuable in an eventual FSM failure if the target
SoC has no harwared mechanisms to support bus recovery.
In this case, bus recovery uses pin information to restore
the I2C bus state.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Adds hda link in and out drivers. The link in and link
out channels of HDA have small differences
with the host channels. Updates the existing
cavs_hda drivers and code to account for these
differences.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
all the consumers of the obsolete pinmux driver is
updated to use pinctrl API, this commit removes
the pinmux driver and assosciated sections.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
This commit has the necessary changes to update the consumers
of pinmux driver(SPI, I2C, UART) and update the board specific
files to use the pinctrl interface.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Add pinctrl driver for CC13XX/CC26XX family of SoCs
to facilitate transition from pinmux to pinctrl.
`IOCPortConfigureSet()` from TI hal driverlib used to
implement the generic pinctrl driver.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
LPTIMER has a different `countermode` meaning.
We shall exclude introduced property from lptim bindings.
Alternative property (e.g. `external-mode`) can be added
later on to support external counter mode.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Introduces H7 FMC bindings with support for
memory remap or swap configuration.
The following values are supported:
* disabled - default mapping (reset state).
* sdram-sram - swaps the NOR/PSRAM and SDRAM banks.
* sdramb2 - remaps SDRAM bank 2.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
the icm42670 from Invensense/TDK is a 6-axis accelerometer with
gyroscope and temperature sensing capabilities.
this initial driver does not support the devices 2K FIFO or many of the
other advanced features. Instead, only basic features are implemented.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Add the period cell to GD32 PWM compatible and update all boards
accordingly. A period of 20 ms (50 Hz) has been set for all PWM LEDs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Rather than specify input clock for each peripheral individually, instead
specify the relevant clocks in DTS.
This will enable easier support for non-default coreclk on fe310 in a
follow-up CL.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
Currently the only way for a BOARD/SOC to configure at compile time the
MPU regions is to add, in a soc-specific file, the 'mpu_config' struct
adding static entries for the new regions with the needed attributes
(cacheable, non-cacheable, etc...). This exported struct is then read by
the MPU driver at boot time and used to properly setup the MPU regions.
At the same time it is now possible to introduce new memory regions in
the DT using the newly introduced 'zephyr,memory-region' attribute.
What is missing is the link between these two solutions: that is how to
declare the memory regions in the DT and automatically configure these
regions in the MPU with the correct attributes.
This patch is trying to address exactly this problem.
It is now possible to declare the memory regions in the DT and define
the MPU attributes for the regions using the 'zephyr,memory-region-mpu'
property. When this new property is present together with the
'zephyr,memory-region' property and a the 'zephyr,memory-region'
compatible, the 'mpu_config' struct is automatically extended at
compile-time to host the DT defined regions with the correct MPU
attributes.
So for example in the DT we can now have:
sram_cache: memory@20200000 {
compatible = "zephyr,memory-region", "mmio-sram";
reg = <0x20200000 0x100000>;
zephyr,memory-region = "SRAM_CACHE";
zephyr,memory-region-mpu = "RAM";
};
and a new region will be created called "SRAM_CACHE" and a new MPU
region will be configure at boot time with the attribute
"REGION_RAM_ATTR".
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add a new boolean devicetree property `tx-rx-swap` to the
st,stm32-usart binding, used to control TX/RX swap during
device initialization.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
Add boolean properties to the binding for the nRF RADIO peripheral
to indicate whether the following features are supported:
- IEEE 802.15.4 mode
- 2 Mbps BLE mode
- coded BLE PHY
- high TX power settings
Set these properties appropriately in devicetree radio nodes for all
nRF SoCs.
Add also such properties and set them in appropriate nodes for nRF
flash controllers to indicate whether they support partial erase.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
For consistency with the scheme used for other nRF peripherals,
use the peripheral name that nRF Product Specifications use.
In this case, it is WDT, not WATCHDOG.
Also remove the requirement for the label property in the binding.
It is no longer needed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add missing devicetree nodes representing the following peripherals
in nRF SoCs:
- ACL
- BPROT
- CCM
- COMP/LPCOMP
- CTRLAP
- DCNF
- MPU (nRF MPU peripheral in nRF51 Series, not ARM MPU)
- MUTEX
- MWU
- NFCT
- OSCILLATORS
- POWER (in nRF51 and nRF52 Series)
- PPI
- RESET
- SWI
- USBREG
Add also corresponding bindings and validation of base addresses of
these nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Adds an initial driver for HDA streams on cAVS. A common code base is
provided for all HDA streams while the drivers are identified
differently as they have small behavior differences.
Uses dma_status to describe the positions for read/write. Uses dma_reload
to inform when to move the read/write positions. This closely follows
how HDA is being used in SoF
Simple test case is provided for both drivers.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add build time optional PINCTRL support to the Microchip XEC TACH
driver shared by MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Update Microchip XEC TACH driver to support MEC172x.
Standardize device tree properties between chips.
Standardize device structure usage.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Depending on the stm32 mcus and the timer instance, several channels
can enable the complementary output for the PWM signal.
Example of a DTS <&pwm1 2 4 (PWM_POLARITY_NORMAL | PWM_COMPLEMENTARY)>;
Note that the timer channel must support the complementary output
on that channel : usually channels 1-3 + channel 4 on stm32g4x.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Follow up on commit 37bf7cb
("dts/bindings: stm32: Set pinctrl-[0/names] properties as required")
Report lack of those fields soon at build to avoid cryptic
DT api build error messages.
Signed-off-by: Maciej Zagrabski <maciej.zagrabski@grinn-global.com>
Instead of having one single WQ per backend, move to one WQ per
instance instead and add a new "zephyr,priority" property in the DT to
set the WQ priority of the instance. Fix the sample as well.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add Nano header connector defined by Arduino. This allows
hardware with compatible headers to define the related GPIOs.
Signed-off-by: Marco Peter <marco.peter@joylab.ch>
Add description for a plain GPIO configuration using
st,stm32-pinctrl and st,stm32f1-pinctrl bindings.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add backlight gpios property to mcux display driver, so that the driver
can correctly initialize the backlight gpio control.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In order for pinctrl support to be complete, RT series GPIO driver must
support pinmuxing within the driver level. RT series pinmux settings do
not correspond directly to gpio port/pin numbers, so use DTS mappings to
pinctrl nodes to select and apply pinmux settings in the gpio driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable pinctrl driver for usdhc. USDHC driver uses custom pinctrl states
for fast, slow, and medium signal frequencies, as well as pin pull for
SD detection.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable pinctrl for flexspi driver. Note that when flexspi is being using
in XIP mode, pinctrl settings are not required and will not be applied.
Pinctrl settings are only required when the flexspi device being used is
not the one used for XIP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
RT11xx series has similar pin configuration peripheral to RT10xx, with
some differences in register layout. Create new pinctrl definition
header file, and reuse existing driver code for RT10xx.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
iMX.RT parts use a GPR register for some pinmux settings. Update pinctrl
driver to support this GPR register definition.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This update Atmel sam and sam0 ethernet gmac and mdio drivers to use
pinctrl driver and API. It updates all boards with new pinctrl groups
format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 rtc driver. It allows to
define pins to be used for tamper detection.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 dac driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 usb dc driver. It updates
all boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 tcc pwm driver. It updates
all boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 i2c driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 spi driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam0 serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update current Atmel sam0 pinctrl initiative to current Zephyr
pinctrl API. It update current devicetree bindings and add the sam0
pinctrl driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam qdec sensor driver to use pinctrl driver and API.
It update board and sample with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam pwm driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition this
remove all remaining manual pinmux at board level.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam canfd driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition this
add missing entries to run automated tests for can/canfd drivers.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam ssc driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition this
remove DEV_NAME macro at sam xdma driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam afec driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition, it
add overlay files to allow run samples/drivers/adc example.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam usb drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam counter driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam i2c drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. This add missing
i2c-0 alias into sam4l_ek board.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam spi driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update current Atmel sam pinctrl initiative to current Zephyr
pinctrl API. It update current devicetree bindings and add the sam
pinctrl driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit makes the transition from the pinmux driver to the pinctrl
driver. It also modifies UART, SPI and I2C drivers used in FE310-based
boards to use the new pinctrl API.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The PLL div-p for the stm32g4x has more possible value than stm32l4
possible ra nge is from 2 to 31
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Adds an entropy driver that uses Bluetooth HCI commands as its source
of randomness. As this method is blocking, the ISR API is not supported.
As this method will range from relatively slow (same core Bluetooth HCI
controller) to extremely slow (UART HCI Bluetooth controller), use the
xoshiro PRNG by default for RNG generation.
Implements #37186
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
added bindings for vnd,reset used for devicetree test reset
added adc temp sensor as supporting reset
Signed-off-by: Andrei-Edward Popa <andrei.popa105@yahoo.com>
added bindings and compatible for reset controller nodes
added bindings for devices that use the reset controller
Signed-off-by: Andrei-Edward Popa <andrei.popa105@yahoo.com>
the tlc5971 driver uses spi for controlling the global brightness
and individiual pixel brightness of a daisy chain of tlc5971
devices.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
If a user has a 1GB external flash it is currently not possible
to configure this through DTS. To allow for such a configuration
we add an option which specifies the size in bytes not bits.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
This commit adds ipc backend, that relies on simple
inter core messaging buffer also added by this commit.
This backend is configurable with DT overlay. Each
ipc instance could be defined with ipc-icmsg commpatible.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Enable pinctrl for ethernet mcux driver, and update kinetis DTS node to
include labelling for PTP node, to enable driver to access pinctrl
properties.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
kinetis pinctrl driver had swapped values for slew rate
(fast slew rate should set bit to zero). Fix slew rate values.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
- Move the SX oscillator control pins to a regulator node
- Create a board level compatible for the RF switch
- Use gpio_dt_spec to simplify board pins.c (now rf.c)
- Cleanup include list
For reference:
https://downloads.rakwireless.com/
LoRa/RAK811/Hardware_Specification/RAK811_HF_Schematics.pdf
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add build time optional PINCTRL support to common PWM driver
for Microchip XEC MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add support for MEC172x series to Microchip XEC PWM driver.
Standardize device tree properties for both SoC families.
Standardize device structure usage.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add the Vref reference voltage in the DTS, so that the adc driver
can retrieve the value for conversion.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
As mentioned in #42882, the I2C of IT8XXX2 is designed for two different
IP blocks, so this PR divides this I2C driver into two compatibles.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Adds 'swj-cfg' property to the F1 pinctrl. It is an optional
property that allows to control Serial Wire JTAG
configuration.
Different configurations allow to free certain IO
pins that can be used in remap or standalone.
That replaces previously used Kconfig approach.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
This contains accessor macros for getting the maximum bitrate supported
by a CAN controller/transceiver combination.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add generic devicetree bindings for simple CAN transceivers.
Always-on CAN transceivers are considered passive and just provide a
maximum supported bitrate.
Active CAN controllers can typically be controlled by the MCU via either
SPI, I2C, or GPIO. Common GPIO controlled CAN transceivers provide
either a stand-by or an enable pin (or both) for controlling the state
of the CAN transceiver.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for the new pinctrl API to the nRF PWM driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF QDEC driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF QSPI NOR flash driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for configuring pins to be used by the nRF PWM, QDEC, and
QSPI peripherals.
A new custom property "nordic,invert" is added to the pin configuration
group binding to allow configuring PWM channel outputs as inverted.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the DMIC driver that handles
the nRF PDM peripheral. Update code of the driver and the related
devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF I2S driver. Update code
of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Bindings for the Xilinx Processor System GPIO controller, both for the
parent controller device as well as the GPIO pin bank child devices.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Add dts binding for rt1xxx pinctrl driver settings. A binding file is
present for the pinctrl node itself, and for the pinctrl child node that
defines all pinmux options
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce ADC properties which indicated if the ADC instances have
dedicated channels for the internal temperature sensor or voltage
reference.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This macro expands to DT_STRING_TOKEN if property exists, otherwise
falls back to default value.
Helpful when a non-required enum binding doesn't mention a default
value, but a default value makes sense to be set in the code.
Including DT_INST_STRING_TOKEN_OR and test code.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Add support for the new pinctrl API to the I2C drivers that handle
the nRF TWI and TWIM peripherals. Update code of the drivers and
related devicetree bindings.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the SPI drivers that handle
the nRF SPI, SPIM, and SPIS peripherals. Update code of the drivers
and related devicetree bindings.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
1. Check I2C Clock and Data is high through GPIO driver instead
of the I2C bitbang registers
2. i2c_xec_poll_write() and i2c_xec_poll_read() will poll to
check I2C clock and data lines are high before initiating the
transaction. The polling will be every 25us for a cumulative
max of 2.5ms
3. wait_completion() will not call recover_from_error() to reset
the controller. Instead will poll for 10ms for the PIN bit to
clear before returning error.
4. wait_completion() will send STOP if the 9th bit is NACK
5. If any errors with current transaction:
(a) Set error_seen flag.
(b) In the next transaction do the recovery process (reset the
i2c controller) if the clk and data lines are high.
Note: error_seen flag is set for Address NACK with Repeated
Start as well.
6. If timeout error occurs in wait_completion():
(a) Set timeout_seen flag;
(b) Wait till the slave will release the clock.
(c) Once slave releases clock send STOP on the bus. If the
timeout occurred while master read, read the I2C DATA register
for the hardware to proceed.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Allow movement detection to be used on hardware
that only has one interrupt line connected.
Change hardware configuration to a bitmask.
Signed-off-by: Andrew Hedin <andrew.hedin@lairdconnect.com>
Add a new hwinfo driver to get the reset cause on
SAM4S/SAME70/SAMV71 SoC series.
The user-nrst dts property has been added to enable external user
resets.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
This commit implements the temperature sensor interface for
the Maxim MAX31875Low-Power I2C Temperature Sensor.
Signed-off-by: Pete Dietl <petedietl@gmail.com>
In nRF53 family of SoCs, GPIO pins must be explicitly forwarded by the
application core to the network core if the latter should drive them.
Add a binding of a generic GPIO pin forwarder.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
The driver was never migrated to Devicetree, this patch converts the
driver to a proper Devicetree based device.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This adds support for the ads101x (ads1013, ads1014, ads1015) and
ads111x (ads1113, ads1114, ads1115) family of i2c adc devices.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
Introduce a new "zephyr,memory-region" compatible to be used when a new
memory region must be created in the linker script from the devicetree
nodes using the compatible.
Remove also the LINKER_DT_REGION_FROM_NODE macro and add a new
LINKER_DT_REGIONS macro to cycle through all the compatible regions.
In the same PR modify the DTS files and the linker scripts.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Intel's adsp needs to set, at a minimum, a clocking bit before the driver
can initialize the designware dma controller. In many ways it is the
designware dmac IP but with additional registers and functionality added
on top of it. So the code structure here follows how the hardware
appears to be designed, layered on top of the designware driver.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
This is the compatible which is used in the blinky sample, so
it's worth trying to add a better example for what you can do with it
in general in the main description.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Exposes the RC register so that the initial value can be set in
the device tree. This is useful in the case where the timer
generates an event but an interrupt is not required.
e.g generate event to sample adc on RC register match.
Tested on Atmel SMART SAM E70 Xplained Ultra board
Signed-off-by: Marius Scholtz <mariuss@ricelectronics.com>
Current uart driver implementation is incompleted regarding the
usage of DT_INST_FOREACH_STATUS_OKAY. If uart0 and uart2 are selected,
build breaks due to peripheral number ordering, which would be
0 and 1 in this case. This fix PR fix this by re-working the macros
and setting proper uart peripheral instances in DTSI, required for signal
routing configuration.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Build shows warning due to incompatible
CPU vendor name. This fixes it and applies
necessary changes in files.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Initial implementation of a simple GPIO controlled power domain.
It exposes no API of its own, all functionality is contained inside
the runtime power management callbacks.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add support for power domains on Zephyr. Power domains are implemented
as simple devices so they can use the existent Zephyr API, for resume
and suspend sync and async and also reference count.
The pm subsystem will ensure that domains are resumed before and
suspended after devices using them. For device runtime power
management, every time the device is got or released the same actions
is done to the domain it belongs.
As domains are implemented as simple devices, it is totally acceptable
a domain belongs to another domain.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add support for disabling automatic retransmission of CAN frames
(similar to CAN "one-shot" mode in the Linux kernel).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Renesas R-Car series contains a PFC (Pin Function Controller).
This module consists of registers for selecting the function of
the multiplexed pins and controls the pull-up resistor on each pin.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Remove the unused base binding for CAN bus devices (as in devices
present on a CAN bus). This binding should have been removed in
2269408572
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
On some platforms, HPET is not wired to trigger IRQ 2.
This would make HPET non-functional if the legacy
interrupt routing bit is set in the global config
register. This adds a DTS flag so the driver won't
set the bit to enable legacy interrupt.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
dts/bindings/timer/riscv,machine-timer must have compatible name
riscv,machine-timer. nuclei,machine-timer is wrong, correct it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
This PR adds the different handling of temperature sensor for the
STM32L5 soc. In this soc, there are some calibration settings which
need to be applied for temperature conversion.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
The dts binding general rules document states that the property
description should explain why the default value was selected
(e.g. "default is the value at power-on").
See comment in #41143
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add fragment:
io-channel-cells:
- input
to binding of the "ite,it8xxx2-adc" and "zephyr,adc-emul" compatible.
It is necessary to use io-channels property.
Signed-off-by: Dawid Niedzwiecki <dn@semihalf.com>
An additional devicetree poperty `single-wire` is added
to uart and usart bindings of stm32. The driver checks this value
during initialization and enables the single wire mode when set.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
The leon3 SoCs were missing definitions of the CPU node. This node is
now required for PM, so that power states can be defined.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Better setting a default value there so DT_PROP() will return something
relevant whether the property is set or not.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
NPCX7/9 has a different ADC register structure. NPCX7 has 3 threshold
detectors from offset 0x14 & has 10 input channels. NPCX9 has 6
threshold detectors from offset 0x60 & has 12 input channels.
This commit fixes the NPCX ADC register structure.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
YAML description file for the On-Chip Memory of the Xilinx
Zynq-7000, DT identifier "xlnx,zynq-ocm".
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
The spi-bus-width property provides information if the target system
has all SIO[0123] pins connected to NOR flash memory.
It must be equal to 4 to enable QSPI 4 IO operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Some flash memories connected to QUADSPI IP block on stm32[fh]7 devices
require proper reset pulse before configuration.
This patch adds two new properties - the 'reset-gpios' phandle,
which allows specifying GPIO pin for RESETn pulse and
'reset-gpios-duration', which provides the time (in ms) for reset
duration.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'flash-id' property defines the number of QSPI's dedicated GPIO
bank (and flash ID), which will be used to communicate with flash
memory.
For example, on stm32h7xx it is possible to use 'quadspi_bk1_*' and
'quadspi_bk2_*' set of pins, so one may need to select between them
when required.
By default - pins from 'quadspi_bk1_*' bank are used, so the
'flash-id = <2>;' property, when your use case (e.g. PCB design)
requires it, forces usage of 'quadspi_bk2_*' pins.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Convert the CAN loopback driver from being configured via Kconfig to
multi-instance configured via devicetree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The vnd,gpio-device compatible is now used by the test GPIO driver
(CONFIG_GPIO_TEST) introduced in #41387. This means that we can't define
new devices with this compatible when CONFIG_GPIO=y.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The pinsN group name can be a confusing in some circumstances, so change
it to groupN. Some platforms (e.g. nrf or gd32) are already using
groupN. Documentation and API tests have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
If there are no console messages input at an interval of 15
seconds, the system will be able to enter suspend mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
So far driver was using SENSE mechanism for all or none edge
interrupts. This was not convenient since in some modules may
require IN event to be used and other did not. Converting it to
use a mask specified in the device tree. Pins indicated in the
mask will use sensing.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a new DT property named "pixel-group-size" that allows users to
configure the driver to refresh the matrix by illuminating multiple
LEDs in particular rows simultaneously. This way the maximum possible
brightness of the LEDs can be increased (as they can be lit longer)
and the timer interrupt handler is executed less frequently, what
results in decreased CPU load, but more GPIOTE/PPI channels needs to
be allocated if the PWM peripheral cannot be used. Thus, it is left
to users to select the configuration that suits them best.
Update definitions of both the bbc_microbit boards with this new
property, using the maximum available group size (to achieve maximum
possible brightness). For v2, no new resources are used (only all
channels in the already used PWM peripheral are now utilized).
For v1, two more GPIOTE and PPI channels are allocated.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Some STM32 series need to configure health test register
for proper RNG behavior.
In addition, some also require to write a Magic number
before writing the configuration.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
- Supporting multiple instances of ivShMem virtual devices.
- Introduces DT based configuration for ivShMem devices.
- Add DTS overlay file to test new multiple ivshmem instance capability.
- Enable BDF unspecified device initialization.
(limited to one instance. An improved version of pcie_bdf_lookup()
will come soon that fixes this limitation)
- Make PCIE DTS file macros available for a proper ivshmem device
properties parsing.
Sample for dts file:
pcie0 {
label = "PCIE_0";
#address-cells = <1>;
#size-cells = <1>;
compatible = "intel,pcie";
ranges;
ivshmem0: ivshmem@800 {
compatible = "qemu,ivshmem";
reg = <PCIE_BDF_NONE PCIE_ID(0x1af4,0x1110)>;
label = "IVSHMEM";
status = "okay";
};
};
Signed-off-by: Michael Schmidt <michael1.schmidt@intel.com>
GD32V SoC uses divided clock from core-clock for machine timer clock.
Add config of clock divide factor to support GD32V.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Implemented driver for the simcom sim7080 modem.
This driver features Socket offloading, TCP, UDP, DNS,
SMS, GPS and FTP.
Signed-off-by: Lukas Gehreke <lk.gehreke@gmail.com>
Remove the requirement for specifying #address-cells and #size-cells
properties for CAN controller devicetree nodes.
CAN controllers do not have a common concept of devicetree child nodes
and thus have no need for these properties. This is in line with
upstream Linux kernel devicetree bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move odr and range properties for both accelerometer and gyro
from Kconfigs to Device Tree.
Fixes#41117
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Fix the yaml dts multi-line property description in the following
(expected) way:
description: |
PUT_TEXT_HERE
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adding support for the TI TMP108 temperature sensor. This includes
over/under temp interrupt support as well as one shot, continuous
conversion and power down modes.
Signed-off-by: Jimmy Johnson <catch22@fastmail.net>
Add a display driver and the corresponding devicetree binding for a LED
matrix with rows and columns driven by nRF SoCs GPIOs. Such matrix can
be found, for example, in the BBC micro:bit boards.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Create an explicit ina230 driver which is supposed to
work with 230 and 231 variants. While at it switch
to i2c_dt_spec helpers and change device-tree node
names to use - instead of _ in order to follow
convention.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by lps22hh driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support for the 8 channels TCA9548A I2C mux.
Added a new binding ti,tca9548a binding inheriting
properties from ti,tca954x-base and defining its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Add an optional "reset-gpios" phandle-array
field to the driver common yaml.
The reset GPIO channel and pin can be defined
in device tree as a node property.
The driver then deassert the reset signal at mux
initialization if a "reset-gpios" has been specified.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Prepare the driver to upcoming support of more mux references.
Rename all TCA9546A related files to TCA954x.
Keep ti,tca9546a and ti,tca9546a-channel compatible
for backward compatibility reasons.
New tca954x-base binding embedding common properties,
tca9546a binding inherits from it and define its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Include the mem-region bindings for the stm32 ccm nodes and set the name
in the current dtsi files.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add the compatible property to the board level sdram nodes in few stm32
dts files so that the zephyr,memory-region name is used correctly in the
linker script.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add bindings for SDL based display controller.
Rework SDL based display controller driver to obtain
configuration from devicetree. Remove unnecessary casts,
add multi-instance support.
Add display controller node and chosen property
to native_posix devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Include common display controller bindings.
Add required height and width properties to "ilitek,ili9340"
and "ilitek,ili9488" users.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Introduce optional `zephyr,linker-region` property which signifies that
the node should result in a linker memory region and what the name of
that region should be. Property added to compatibles likely to result
in a linker memory region; 'mmio-sram', 'arm,itcm`, `arm,dtcm`,
`nxp,imx-itcm`, `nxp,imx-dtcm` and `fixed-partitions`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Refactor the mcp230xx driver to generically also support
SPI IO expanders, renaming it to mcp23xxx in the process.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add driver for MEC172x QMSPI with local DMA(LDMA). The driver
support SPI asynchronous operation.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
This commit adds a generic i2c regulator driver, and enables the NXP
PCA9420 PMIC IC using this driver. The regulator driver also exposes an
additional API in include/drivers/regulator/consumer.h, which allows
drivers to implement support for adjusting voltage levels and current
limits, if their device supports it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
There is currently no information available about the XIP
addresses for the nRF52840 and nRF5340.
Add this via a new 'reg' block in the relevant QSPI nodes, along with
names for the register blocks so they are easier to retrieve.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Adds a driver using the SNVS high power and optionally low power
RTC instances. A device specific function `mcux_snvs_rtc_set` is
provided to update the current counter value.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
The commit adds "disk-access" property to fstab bindings to allow
selecting FS_MOUNT_FLAG_USE_DISK_ACCESS while defining file
systems in DTS.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This adds an spi master mode driver via bitbanged gpio. Only syncronous
transfers are implemented. Clock signal timing is accomplished via busy
waits, the gpios are manipulated via the standard gpio interface; these
two factors limit the frequency at which it can operate - but here
a simple and generic implementation was chosen over performance.
The driver supports the various clock polarity and phase
configurations, and can also work with word sizes which are non
multiples of 8bits, currently up to 16 bits.
A sample program is also added demonstrating basic use of the driver
with 9bit data words.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Adds optional device tree properties to insert delays between spi chip
select assert/deassert and the clock edges, and also between spi
frames and transfers to the mcux flexcomm spi driver. If the properties
are not set, no additional delay is inserted.
Verified expected behavior on mimxrt685_evk and check with a scope
that the pre- and post-delay could be changed from the device tree
properties.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
This commit adds support for IMX6SX PWM.
The PWM module is the same module present on the IMX7D and so dts
bindings has been renamed following the one present on linux.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Most of the time SPI devices use TI's frame format. But some may use
Motorola's. This is already taken care of in the SPI API and now it will
be possible to select the right format from DTS. Like:
...
frame-format = <SPI_FRAME_FORMAT_MOTOROLA>;
...
This is only meant to be used for devices supporting both formats (so
the format is not hard-coded in the driver) and selected by hardware
configuration or else. Which, in such case, it will need to use
DT_INST_PROP(<instance number>, frame-format) macro call to retrieve
the property value. Others can fully ignore it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Software reset is already implemented in the driver when the
`reset_gpio` is not defined. However it could not be activated
because the `reset_gpio` is a required field in the DTS
binding.
Signed-off-by: Casper Meijn <casper@meijn.net>
This patch adds support for the new pinctrl API to the UARTE driver. The
old pin property based solution is still kept so that users have time to
transition to the new model.
Notes:
- Some build assertions cannot be performed since the driver does not
have direct access to pin settings anymore. As a result user will not
be notified if HWFC is enabled but RTS/CTS pins are not configured.
- Hardware flow control can be enabled regardless of pin configuration,
it is now up to the user to configure RTS/CTS pins in DT.
- Some RX enable checks that were performed using pin information has
been replaced with a DT property that informs if RX is enabled or not.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add initial support for nRF pin controller driver. The implementation in
this patch does not yet support any peripheral. Only states
representation and basic driver functionality is introduced.
Note:
The nrf_pin_configure function has been marked as __unused since it may
not be used in certain scenarios until all peripherals are supported by
the pinctrl driver. For example, if only UART/E is supported but the
board does not enable UART, the function will never get called. However,
that board will likely have other peripherals that will gain support in
the future.
Thanks to Marti Bolivar for bindings documentation.
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Now that STM32 drivers are using pinctrl API, set pintrl-0 and
pintrl-names properties as required in order to report malformed
nodes description soon at build stage and avoid cryptic
DT api build error messages.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new pinctrl API to configure pins.
Since STM32F1 series require pinctrl option and required register
address is parent timer address in place of own node register address,
use PINCTRL_DT_INST_CUSTOM_REG_DEFINE in place of usual
PINCTRL_DT_INST_DEFINE for this specific series.
Additionally, remove the automatic selection of PINMUX API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new pinctrl API to configure pins.
Additionally, rename usb_pinctrl to usb_pcfg to better fit
new pinctrl API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the I2C peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use nrfx_gpiote and nrfx_ppi allocators to allocate channels
at runtime instead of fixed, device-tree based allocation which
is harder to maintain.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add bindings for a generic PCIe Controller in ECAM mode.
ECAM stands for PCI Express Enhanced Configuration Access Mechanism
where the PCIe config space is flat memory-mapped.
An optional msi-parent phandle is added to link to an optional
MSI/MSI-X Interrupt Message Translation HW component.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a new RPMsg with static VRINGs backend. This new backend makes
easy to generate and use IPC instances backed by OpenAMP using the DT.
Each instance is defined in the DT as (for example):
ipc: ipc {
compatible = "zephyr,ipc-openamp-static-vrings";
shm = <&sram_ipc0>;
mboxes = <&mbox 0>, <&mbox 1>;
mbox-names = "tx", "rx";
role = "primary";
status = "okay";
};
It is then possible to register an send data through endpoints using the
IPC service APIs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
* With existence of Adafruit Qt Py boards, and upcoming wireless
Xiao from Seeeduino, define nexus node and peripheral node
labels for use with shields that accept any Xiao format board.
* Adds `&xiao_d`, `&xiao_spi`, `&xiao_i2c` and `&xiao_serial` generic
node labels.
* Add new 'seeed-xioa-header.yaml` to document new nexus node.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add a pin control driver for GD32 SoCs using the AFIO model.
Thanks to Gerson Fernando Budke for testing and implementation
suggestions.
Co-authored-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
1.Putting the PWM_CHANNEL_X, PWM_PRESCALER_CX information
in the description.
2.Use the common definition EC_FREQ.
3.Use the common macro IT8XXX2_DT_ALT_ITEMS_LIST.
4.Stop using DRV_CONFIG, DRV_REG macro.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Users will have to include dt-bindings/spi/spi.h in order to use the
relevant flags fol this property. For instance:
...
duplex = <SPI_HALF_DUPLEX>;
....
By default all SPI device are configured to be full duplex so the
property is optional. This property makes sense only for devices that
can be configured on either modes. Which, in such case, it will need to
use DT_INST_PROP(<instance number>, duplex) macro call to retrieve the
property value. Others can fully ignore it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add tests for the instance based enum macros DT_INST_ENUM_IDX and
DT_INST_ENUM_IDX_OR.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
IT8XXX2 uses shared ns16550.c driver which does not provide a power
management callback(pm_action_cb), so create driver to handle
IT8XXX2 specific UART features.
note: pm_action_cb(old name: pm_control_fn)
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Prescaler was misplaced in pwm binding, instead of timers binding.
For example, TIM6/TIM7 doesn't have PWM capability,
but have a prescaler.
Also prescaler is common to all PWM channels of the same timer.
This change also prepares the introduction of timer based counter
(which requires prescaler at timer level)
For compatibility reason temporarily keep pwm binding to avoid
breaking boards out of tree.
Block st,prescaler property in lptim binding
as lptim doesn't use this property for now.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This will be used to take a phandle to a FEM device, either a generic
two pin device or an nRF21540. Keep the nRF21540 binding example up to
date.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The way the nRF21540 device is configured makes sense once you
understand it, but it's quite unusual: a single peripheral is
configured with two separate devicetree nodes linked by a phandle.
Since this risks entering "exploding head" territory for beginners, it
deserves a thorough example. Add one to the binding's description.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is a helper binding for radio front-end modules that have a
two-pin control interface, where one pin is used to turn on an power
amplifier (PA) for TX, and another is used to turn on a low-noise
amplifier (LNA) for RX.
Such hardware is already supported by the Bluetooth subsystem, but via
PA/LNA Kconfig settings. Since this is hardware configuration, it is
better to move this to devicetree instead.
Add a binding that makes it possible to define nodes which contain the
same information, along with a bit of extra information related to the
gain in dB of each amplifier not currently available from Kconfig.
This is similar to the existing binding for the nordic,nrf21540-fem
compatible.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Andrzej Kuros <andrzej.kuros@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is to support upcoming external radio coexistence implementations,
see binding documentation for more info.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
add ledc to board dtsi file,
change compatible and device define in pwm driver,
add yaml for board ledc support,
fix missing include for board in gpio include
Signed-off-by: Andrei-Edward Popa <andrei_edward.popa@upb.ro>
Use i2c_hal functions to enable support for
multiple SoCs.
Use DT compat to enable I2C from device
tree configuration
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This joins all clock control handling to same source
by using hal clock functions. It also brings ESP32C3
clock support.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
In order to have Espressif SoCs working with
the same uart drivers, all low level functions
are now replaced to hal_espressif HAL calls.
This also changes pinmux, gpio and uart
init order to meet its dependencies.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
STM32WL could be either single core (stm32wlex) or
dual core (stm32wl5/4x).
Make CPU2 prescaler an optional property (while it will
be required if inherited from st,stm32wb-rcc.yaml.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that Kconfig option for STM32 clocks configuration has been
removed, set rcc properties as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added watchdog implementation which is using counter device
to implement watchdog driver API. Watchdog timeout is called from
counter interrupt context. Some counter implementations support
using ZLI interrupt level which can be use here as well. Watchdog
like this can be used along hardware watchdog to cover for its
limitations, i.e. Nordic watchdog resets unconditionally after
62uS after triggering watchdog interrupt. It is not enough time
to dump logging data.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The FIU/UMA module in the NPCX chip provides an dedicated SPI interface
to access the SPI flash. This commit adds the driver support for it.
With this commit, the application can call the flash APIs
(via spi_nor.c) to access the internal flash of NPCX EC chips.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I32bbf09f6e014b728ff8e4692e48151ae759e188
Rewrite the NRFX IPC driver to properly support multi-channel addressing
leveraging the newly introduced MBOX APIs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
One limitation of the current IPM API is that it is assuming that the
hardware is only exporting one single channel through which the data can
be sent or signalling can happen.
If the hardware supports multiple channels, the IPM device must be
instantiated (possibly in the DT) several times, one for each channel to
be able to send data through multiple channels using the same hw
peripheral. Also in the current IPM API only one callback can be
registered, that means that only one driver is controlling all the
signalling happening on all the channels.
This patch is introducing a new MBOX API that is supporting
multi-channel signalling and data exachange leveraging and extending the
previous (and outdated) IPM API.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This is a driver for the Synopsys DesignWare MAC. It should work
with the "DesignWare Cores Ethernet Quality-of-Service" versions 4.x
and 5.x.
This driver uses a zero-copy strategy, meaning that the hardware
reads and writes data directly from/to packet fragment buffers
provided by the network subsystem without first copying the data into
a dedicated DMA bounce buffer.
Platform specific setup is necessary for the hardware to work.
Currently, only the STM32H7X series is implemented and tested.
While this part needs refinement, this driver performs better and uses
far less code space than the HAL-based alternative.
Not yet implemented:
- MDIO (it is WIP, currently relying on default PHY config)
- PTP support
- VLAN support
- various hardware offloads (when available)
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
MEC172x eSPI driver, eSPI pin programming, interrupt updates related
to eSPI and other updates for MEC172x eSPI driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add a set of tests to check the API behavior. The API tests can only run
on a platform that does not have an actual pinctrl driver, e.g.
native_posix. The test itself implements a pinctrl mock driver and
provides the required "pinctrl_soc.h" header with required types/macros.
The implementation is used in the tests to verify the behavior of the
API or Devicetree macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
When using group based representation on pinctrl nodes, the pin
configuration properties end up being at the grand-children level, so
the `pincfg-node.yaml` file can't be used.
Having a common file that can be used for both cases would require
tooling changes, so for now a copy that operated at the grand-children
level has been created.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Initial skeleton for pinctrl drivers. This patch includes common
infrastructure and API definitions for pinctrl drivers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move odr options from Kconfigs to Device Tree. Moreover add
in DT a power-mode option to select among 4 possible values
(PD, LP, HR, HF). The power mode cannot be currently set from
sensor APIs.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all DT
bindings (as i2c and spi) handled by lis2ds12 driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add a dedicated compatible for STM32MP1 clock control node.
Since, on such platform, clock configuration is done on A9
side, only the clock-frequency property is available.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add general mboxes, mbox-names to base.yaml to be utilized by any
clients that use mailboxes.
Additionally add mailbox-controller.yaml for common properties shared
by all mailbox controller devices.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Currently all the *-names and *-cells properties are derived from the
name of the base <name>s property. This is a limitation because:
- It forces the base property name to be plural ending in -s
- It doesn't allow the english exception of plural words ending in -es
With this patch we add one additional property 'specifier-space' that
can be used to explicitly specify the base property name.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Suggested-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The shared multi-heap memory pool manager uses the multi-heap allocator
to manage a set of reserved memory regions with different capabilities /
attributes (cacheable, non-cacheable, etc...) defined in the DT.
The user can request allocation from the shared pool specifying the
capability / attribute of interest for the memory (cacheable /
non-cacheable memory, etc...)
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add specific properties to enable remap for PA11/PA12, which is a
possibility on STM32G0/F0 SoCs.
These properties only have effect when defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This name should be the same as cpus node in dtsi. After the power
policy is added, the cpu-power-states in the CPU properties can
be used.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
AHB prescaler is a value which divides the SYSCLOCK
to provide the HCLK. The HCLK supplies the core, AHB bus, memory.
On the stm32wb and stm32wl, the HCLK for CPU1 is HCLK1
with cpu1-prescaler.
By default the value is 1, else the HCLK must be correctly set.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
interrupt controller, also places its relevant
peripheral sources allowing drivers to use the
DT macros instead of espressif headers.
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
This reverts commit d3a558591f.
We shouldn't be adding vendor prefixes for things we don't have
upstream bindings for unless we've inherited them from Linux.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
If supported by the SPI instance and soc, this property will
configure the frame-format to be compliant with the TI mode.
By default, if supported, the frame-format is Motorola mode.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add DT bindings for the optional Interrupt Translation Service module
of the ARM GICv3 Interrupt Controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Implements a shim layer driver using st hal for
I3G4250D gyro, mounted for example on stm32f3_disco_E.
No support for triggers included yet.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
1. Add support for multiple syscon entries (as a side effect, this also
fixed syscon.c implementations which weren't being linked to their
syscon.h counterparts).
2. Add support for different width registers in syscon.
3. Add tests for syscon
Signed-off-by: Yuval Peress <peress@chromium.org>
TWIM peripherals cannot perform write transactions from buffers
located in flash. The content of such buffers needs to be copied
to RAM before the actual transfer can be requested.
This commits adds a new property (zephyr,flash-buf-max-size) that
informs the driver how much space in RAM needs to be reserved for
such copying and adds proper handling of buffers located in flash.
This fixes an issue that caused that e.g. the DPS310 sensor driver
did not work on nRF SoCs that only have TWIM, not TWI peripherals.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Issue an error logging message when the i2c_nrfx_twim driver lacks
a concatenation buffer big enough to properly handle a call to
i2c_burst_write() function, to give the user a hint what is wrong.
Also use by default a 16-bytes long concatenation buffer for every
instance of the i2c_nrfx_twim driver. Such value should cover most
of the simple uses of the i2c_burst_write() function, like those
in the stmemsc sensor drivers, and when a longer buffer is needed,
the user will be provided with the above message pointing to the
property that should be adjusted.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove the HL7800 DTR device tree binding because the
DTR IO is not needed for operation of the HL7800
modem.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Add a shim that allows using the nrfx PDM driver via the Zephyr API.
Add also missing devicetree nodes representing the PDM peripherals
in the nRF52 Series SoCs.
Extend the "nordic,nrf-pdm" binding with a new property that allows
specifying the clock source to be used by the PDM peripheral (so that
it is possible to use HFXO for better accuracy of the peripheral clock
or, in the nRF53 Series SoCs, to use the dedicated audio oscillator).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The max-erase-time property was introduced for the STM32 flash driver,
but it was inserted as an optional property in the generic
soc-nv-flash binding which is used by other SoCs.
Make it a required property in a new st,stm32-nv-flash binding
instead, since it is at present a vendor specific property.
Update the DTS files accordingly. Keep the existing "soc-nv-flash"
value in the compatible list in each case, so that DT_HAS_COMPAT(...
soc_nv_flash) tests on these nodes will still succeed, but put it
after a newly added "st,stm32-nv-flash" compatible, so that the
SoC-specific binding will be used as it is discovered first by the DT
tooling.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Note that the it8xxx2 does not support a status register so that
functionality is omitted.
This change also adds driver tests that build both the npcx and it8xxx2
drivers.
Signed-off-by: Yuval Peress <peress@chromium.org>
This commit adds support for Ethernet PHY drivers via a PHY API.
It also includes a driver for a generic MII compliant PHY
which supports most PHYs on the market.
Separating PHY driver from the SoC specific Ethernet driver
simplifies the Ethernet driver code and enables code re-use.
Drivers for specific PHYs with more advanced features, such as
RGMII delay in PHY can be developed independent of the Ethernet
MAC driver.
Signed-off-by: Arvin Farahmand <arvinf@ip-logix.com>
Add Digital-to-Analog Converter driver (based on DACC module) for Atmel
SAM MCU family. Only SAME70, SAMV71 series devices are supported in
this version.
Tested on Atmel SMART SAM E70 Xplained board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Microchip MEC172x series I2C driver implementing controller
and target modes. The driver implemenents its own I2C port
pin control functions and does not depended upon pinmux. Future
updates will make use of PINCTRL when that subystem is finalized.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This adds basic support for the Silabs Si7210 hall effect magnetic
position and temperature sensor. It is able to get magnetic field and
temperature in the default scale of the sensor (depending on the
variant). It also supports going into sleep mode without measurements
through the device power management infrastructure.
It is most notably missing support for scale change, measurement
averaging and filtering, and alert pin configuration (threshold,
hysteris, tamper).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
STM32WL features a specific HSE clock with dedicated properties.
Add a dedicated binding and update STM32 clock control driver
header to take it into account.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add hidden Kconfig option to Kconfig.cdc and allow
to configure CDC ACM UART device from devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Current USB device controller drivers (drivers/usb/device)
do not use DEVICE_DT_GET but the properties from devicetree,
and USB device controller node is parent for CDC ACM UART and
AUDIO children nodes.
Add USB device controller binding and node to keep the samples
building for native_posix driver.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
This adds support for the TI INA219 Zero-Drift, Bidirectional
Current/Power Monitor with I2C Interface
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
The way we currently handle direction finding extension (DFE) support
on Nordic nRF5 controllers relies on required devicetree properties
related to DFE in the "nordic,nrf-radio" node.
That doesn't make sense on radios without DFE support, though.
Any .dtsi for an SoC without DFE support which has such a node would
require extraneous DFE related properties like dfe-antenna-num.
Instead of making the properties required, mark them optional. We
indicate the presence of DFE support via a new 'dfe-supported' boolean
property which the SoC .dtsi files can set (or not) depending on
support.
This gives us the opportunity to do some cleanup in the Kconfig,
removing CONFIG_HAS_HW_NRF_RADIO_BLE_DF since we know from the
devicetree whether DFE support is available.
Handle that change appropriately in radio_df.c. This gives us an
opportunity to improve readability in the devicetree-related macro
magic in that file.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The documentation for Bluetooth Direction Finding Extension (DFE)
samples has various issues:
- references to 'child' images, which do not exist in mainline zephyr
- invalid RST syntax: there are missing ` characters to end arguments
to :zephyr_file: roles, creating unintelligible output
- incorrect RST usage:
- using :zephyr_file: instead of :file: when referring to a file
that the user must create, creating broken links to nonexistent
files in the zephyr tree
- using :code: instead of :kconfig: to refer to kconfig options,
creating output without links to the help for those options
- redundant or duplicated information
- grammar, typos, various bits and pieces
Clean this up. As part of that, move various common bits and pieces of
information to the devicetree bindings index so they can just be
linked to from the sample docs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The Linux vendor prefixes list uses 'cdns'. Match it, especially since
we have that prefix in our own list as well.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
These IP blocks' vendor is Cadence, whose proper vendor prefix is
'cdns' if we are going to match the Linux vendor prefixes list.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
As far as I can tell, 'vexriscv' does not name a vendor:
https://github.com/SpinalHDL/VexRiscv
It also doesn't seem entrenched enough to merit a special case
exception to the de factor rule 'the "vnd,foo" namespace is for
vendors'. This is open to debate and we can revise as needed in the
future, but for now let's just rename the compatible to avoid
triggering warnings/errors about unknown vendors.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The original NIOS-II developer and former vendor is Altera, which is
now part of Intel. Let's not add a new vendor prefix for something
that already exists and has been acquired; move it to use the existing
'altr,' prefix instead.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename:
- grove,light to seeed,grove-light
- grove,temperature to seeed,grove-temperature
The "grove" brand applies to a family of products by Seeed (sic):
https://www.seeedstudio.com/category/Grove-c-1003.html
Therefore we should use the existing vendor seeed.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
I can't find any reference anywhere showing that the manufacturer of
the LPD8803 or LPD8806 LED scripts is a company called 'colorway'.
Use 'greeled' instead; these seem to actually be manufactured by
GreeLed corporation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
It should be "maxim,max30101", because the vendor prefix for this
company is "maxim", not "max".
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
It should be "u-blox,sara-r4", because the vendor prefix for this
company is "u-blox", not "ublox".
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We have a ftdi,ft800 binding, and it's easy to imagine additional
bindings coming in the future since their USB/UART chips are very
commonly used.
I didn't find anything in Linux for this vendor.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is used for microbit,edge-connector. I couldn't find anything in
Linux, which is not surprising given these boards have constrained
Cortex-M chips.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We have various compatibles matching this in a DTSI file.
Linux tracks this vendor too:
4071883fd8
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We have a binding for apa,apa102 in zephyr.
I can't find any bindings for this vendor in Linux.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We have a binding for compatible "quectel,bg9x".
I can't find any bindings for this vendor in Linux.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We have a binding for wiznet,w5500 in zephyr.
Linux has a binding for this device, too:
d5ad8ec3cf/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
But 'wiznet' is not present in the Linux vendor prefixes file for some
reason.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This PR will change accessing the related pinctrl macro from soc_dt.h
And the pinctrl of SCL and SDA were got from pinctrl-0 and pinctrl-1,
respectively. Change it to get from pinctrl-0 only.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This adds the driver for Omnivision OV2640 image sensor.
The driver provides support for 10 different resolutions in range from
160x120 to 1600x1200 in both JPEG and RGB565 pixel formats. There are
also mutliple configuration options, e.g. hflip, vflip, saturation and
brightness control.
Signed-off-by: Robert Szczepanski <rszczepanski@antmicro.com>
Add sifive-e24 cpu binding. This introduce riscv,cpu binding to
be used as riscv cpu base and riscv,sifive, which define specific
properties for this vendor. Both are necessary to create the e24
core.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add missing dts binding for sensor, this was causing build errors with
CONFIG_PM set on bt510/bt6x0 boards.
Fixes#37675
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add ADC driver version 2 for MEC172x using new in-tree headers
and device tree properties. Update the ADC shell for the new driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Introduce a new API to allow devices capable of wake up the system
register themselves was wake up sources. This permits applications to
select the most appropriate way to wake up the system when it is
suspended.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Microchip XEC has been using the standard NS16550 driver.
Using the standard NS16550 driver requires extra HW programming
for XEC UART in board level and did not support XEC GIRQ interrupt
programming. We add an XEC specific driver and remove UART specific
register programming from the board level and implement interrupt
support. Also, by implementing a SoC specific driver we can add
driver PM in the future.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Microchip XEC two custom DT properies girqs and pcrs cell sizes
are defined as constants. There is no need to replicate these
is the chip DTSI since the value cannot be changes. Fix the syntax
of the cell size constant to match the naming convention used
thoughout DT.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
based on uart rom functions, also enable console driver
on top of this driver, which enables logging
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Add optional support for the DRDY/INT pin. This avoids waiting a fixed
time for the temperature and humidity conversion to finish.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The ipm_stm32_hsem driver is a virtual mailbox based on STM32 HSEM.
Since we already have LL_HSEM(low-level HSEM) API on the hal_stm32
module, looks there is no need to implement a new HSEM driver.
But there are still have some limitations, the HSEMx interrupt is
not shareable. If another HSEM user wants to use the HSEMx interrupt,
the ipm_stm32_hsem mailbox needs to be disabled.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
This is a follow-up to commit 3656ba5ae9.
Do not enforce pull-up resistors to be enabled on RXD and CTS pins
in nRF UART drivers, as in certain hardware designs this may be
undesirable or may even make certain hardware not working.
Instead, provide devicetree properties that allow enabling of those
resistors when it is actually needed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The driver only support use case where the channels are used in mutual
exclusion.
Origin: Original
Signed-off-by: Guillaume Lager <g.lager@innoseis.com>
Update the Microchip XEC pinmux driver to use system I/O
routine for read/write of registers instead of direct use
of volatile and CMSIS defines. Add GPIO port number to
bindings instead of using hard coded value from chip headers.
Modify SoC DTSI pinmux syntax, requires "pinmux: pinumx {..."
or the DT macros will not work. Since pinmux is used by MEC152x
we update its chip pinmux DT.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add support for TI TLC59108 an I2C 8-bit LED driver.
Supported blinkink period: 41ms to 10730ms
Supported brightness value: 0 to 100%
This driver supports the following APIs:
1. led_blink
2. led_set_brightness
3. led_on
4. led_off
This is a modified version of the NXP PCA9633 driver.
Signed-off-by: John Kjellberg <kjellberg.john@gmail.com>
Use a comment syntax instead of a separator. This is a bit cleaner
and is prep work for moving the parsing code to a more generic place,
namely edtlib.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Update our vendor-prefixes.txt file to match the data in upstream
Linux's vendor-prefixes.yaml file as of Linux commit
8ac91e6c6033ebc12c5c1e4aa171b81a662bd70f.
(We can't easily switch to using the Linux YAML file directly because
our documentation tooling depends on this plain text format.)
The changes were done using a script and then cleaned up by hand in
order to not throw away any Zephyr-only prefixes, and to manually
override Linux in some cases.
List of Zephyr-only prefixes, all of which were kept:
asmedia
cadence
gaisler
lairdconnect
ovti
openisa
particle
quicklogic
ruuvi
segger
vnd
weact
zephyr
Other things to note:
- keep Espressif as 'espressif', overriding Linux's 'esp'
- 'gw' is deprecated in Linux and is unused here; just remove it
- ROCKTECH DISPLAYS LIMITED SHOULD HAVE BEEN ALL CAPS;
HOW COULD WE POSSIBLY HAVE MISSED THIS BEFORE?
- Did not include '70mai' from upstream, as that violates the legal
compatible regexp
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
based on uart rom functions, also enable console driver
on top if this driver enabling logging
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
The booter (bootloader) behavior may be different in different NPCX
chip series. One example is that the booter sets host interface type in
NPCX7 series but leave the firmware to set it in NPCX9 series.
This commit adds a new DT node to record variants in its properties.
NPCX drivers can understand if they need to configure the related
setting by checking the node's properties.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
The Texas Instruments TCA9538 is an 8 pin GPIO port expander.
It operates on an I2C bus with 2 configurable address pins. The
device has an interrupt output pin that is asserted when any pin
configured as an input changes state.
Added under the PCA953X name to allow other similar parts to
use the same driver.
Signed-off-by: Kieran Mackey <kieran.mackey@lairdconnect.com>
Microchip MCP7940N is a Real-Time Clock/Calendar. It operates on a I2C
bus. It can be used to set a calendar time and has two alarm channels.
When an alarm is asserted the state of the MPF pin of the MCP7940N will
change (depending on gpio active high/active low setting) to trigger an
interrupt.
Signed-off-by: Kieran Mackey <kieran.mackey@lairdconnect.com>
Add Atmel sam0 sercom[uart] pinctrl bindings and implements pinctrl at
driver level. It changes all sam0 boards to use new feature and remove
pinmux driver dependency for sercom[uart]. The samples that require a
binding were update to keep consistency and avoid errors.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Busy simulator is using counter device and entropy device to
generate random cpu load. Counter device cofiguration can be
used to set cpu load interrupt priority and optional pin that
can be set during the load.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add initial basic description for Cortex-M33 based
stm32u5 soc series.
This encompass description for base nodes, such as:
- cpu
- flash
- clocks
- sram
Additionally, provide description for variant stm32u575Xi.
Related to clocks nodes, added bindings for stm32u5 specific
rcc node as well as msi and pll clocks.
Header file stm32_clock_control.h was also updated to support
these new bindings.
Note that for compatibility with existing definitions, clock
node describing main pll clock, known as "PLL1", was given two
labels: "pll" and "pll1".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The type of DMA for the stm32f0 devices was wrong
Its DMA is of type V2bis where the peripheral request is fixed.
The corresponding DMA cell has 2 elements.
The stm32f091 has two DMA instances.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add a shim that allows using the nrfx I2S driver via the Zephyr API.
Add also missing devicetree nodes representing the I2S peripherals
in the nRF52 Series SoCs.
Extend the "nordic,nrf-i2s" binding with a new property that allows
specifying the clock source to be used by the I2S peripheral (so that
it is possible to use HFXO for better accurracy of the peripheral clock
or, in the nRF53 Series SoCs, to use the dedicated audio oscillator).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Create version 2 of the MEC GPIO driver to support MEC172x to not
interfere with MEC152x. When the MEC172x ECIA interrupt aggregator
driver is ready, this driver will use ECIA for registering GPIO
interrupt callbacks instead of maintaining its own interrupt table.
Add V2 DT binding.
Add the Kconfig configuration settings for the MEC172x GPIO
V2 driver at the SoC and board level.
Add port id to DT allowing use of DT FOR EACH macro in the driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This driver supports the TI INA230 and INA231 Bidirectional Current
and Power Monitors. The devices work on the I2C interface and are
created from DT nodes with a compatible property matching "ti,ina23x".
The following datasheets were referenced while developing the driver:
https://www.ti.com/product/INA230https://www.ti.com/product/INA231
Twister passed:
twister -T tests/drivers/build_all/sensor/
Testing was performed on the stm32g071b_disco board with the following:
Load: ~170 ohms
Voltage: 5V
Measured Values:
Voltage: 5.1 V
Current: 0.032 A
Power: 0.157 W
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Update Microchip XEC RTOS timer driver adding MEC172x support and
using more device tree properities in the driver. We must also update
the XEC counter driver to use the new GIRQ DT properties.
Add new properties to RTOS timer and RTC timer YAML. These two timers
are linked due to option using a high speed timer for kernel busy wait.
Add Kconfig logic for XEC RTOS timer to MEC172x SoC.
Enable the Microchip XEC RTOS timer in the MEC172x evaluation board.
Add device tree nodes for most peripeherals.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add driver implementation and header files for a MEC172x
aggregated interrupt driver. Enable the parent(ECIA) node
to have the driver initialize interrupt hardware for use.
Enable child nodes for those GIRQs used for aggregation.
Refer to chip documention for the list of GIRQs restricted
to aggregation and those which support direct mode.
Add chip level device tree node for MEC172x EC interrupt
aggregator parent and GIRQ children. Each child node contains
a list of sources representing the source bit position in the
GIRQ registers.
Add DT bindings for ECIA and GIRQ nodes.
Add build file(s) and configuration items for the MEC172x ECIA
aggregated interrupt driver. Add and enable the MEC172x interrupt
driver on the MEC172x evaluation board(EVB). Enable parent node to
initialize ECIA hardware. Child nodes are left disabled until a
future driver needs them.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add basic counter driver based on Timer Counter (TC) module for Atmel
SAM family.
Remarks:
- The driver is not thread safe.
- The driver does not implement guard periods.
- The driver does not guarantee that short relative alarm will trigger
the interrupt immediately and not after the full cycle / counter
overflow.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds bindings for the STM32 AES accelerator.
Common properties of st,stm32-cryp are moved into
st,stm32-crypto-common.yaml.
The accelerator supports ECB, CBC, CTR, GCM, GMAC, and CCM
chaining modes.
128 bit bit data blocks with cipher key lengths of 128 and 256 bit are
supported.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Add support for power management and the shutdown mode for bq274xx fuel
gauge sensor. This now allows boards that have any kind of low power
mode to turn on or off the sensor.
Tested on a Company's custom board with bq27421 sensor on it.
Signed-off-by: Luka Lopotar <luka.lopotar@greyp.com>
This will define a new bindings for any stm32 dma feature
Depending on the soc family, the DMA is of V1 or V2 or Vbis type
And give a factored definition for feature
The difference is on the dma-cell structure.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Implement a clock control driver for Microchip MEC172x handling
configuring the 32 KHz input sources for the PLL and peripheral-32k
clock domains. MEC172x differs from MEC152x. MEC152x had one 32K source
for both PLL and peripherals. MEC172x allows the two domains to use
independent 32 KHz sources. Device tree updated to provide addresses
of hardware used by the driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This commit adds a driver implementation for the LM75 I2C temperature
sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@leica-geosystems.com>
This patch states that the Everlight B1414 LED controller is compatible
with the Worldsemi WS2812. Some information about it is added to the
WS2812 DT binding and driver Kconfig files.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Some devices compatibles with the WS2812 IC have a different reset/latch
delay.
This patch introduces the "reset-delay" optional property for the WS2812
DT binding and adds support to the ws2812_spi driver. This new property
allows to configure the reset/latch delay of a WS2812 compatible LED
strip controller from its DT node.
If omitted the driver uses 8 microseconds by default (which is good for
the WS2812 IC).
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Some devices compatibles with the WS2812 IC have a different channel to
color mappings (e.g. RGB, BGR, RGBW, etc).
This patch introduces the "color-mapping" required property for the
WS2812 DT binding and adds support to the ws2812_gpio and ws2812_spi
drivers. This new property allows to configure the color to channel
mapping of a WS2812 compatible LED strip controller from its DT node.
Since this property also allows to know if a white channel is available,
then this patch removes the "has-white-channel" property.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Add a new property to the "nordic,nrf-clock" binding to allow
configuration of the HFCLKAUDIO frequency.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The zephyr sam gmac driver don't get register address and, in some
cases, peripheral id from devicetree. This replace headers constants
in favor of devicetree values.
This fix wrong Atmel SAME7x/SAMV7x gmac register address and add
missing peripheral id property for SAM family.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current GMAC compatible not allow especialize properties by SoC
family. Split current generic Atmel GMAC compatible into two new
compatibles which are defined by SoC families. This increase the
freedom and avoid odd situations.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This fixes properties documentation and two devicetree styles:
- properties with wrong code identation and
- property description tag style
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
A syscon device is a device managing a memory region containing a set of
registers that are not cohesive enough to represent as any specific type
of device. We need a driver for that because several other drivers could
use the same region at the same time and we need to io-map the region at
boot for MMU enabled platforms.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This adds support for controlling the SUBGHZSPI NSS line in STM32WL
devices. This is a special dedicated SPI port only connected to the
radio device internally, chip select happens through a bit in the PWR
module. Adding a special dt-property to identify the port, it all gets
built out on non-WL devices.
Deduplicate the existing dts bindings in the process, and add the new
one for the special spi with the new property.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add a dts node for st,stm32wl-subghz-radio. The device is integrated in
STM32WL series SoCs, and based on the sx1262, but it does not use any
gpio as all the necessary signals are internally connected to various
SoC units.
To account for that, make the redundant gpio optional in the template
files, but mark them as required in the sx1261 and sx1262 definitions,
to match with what's used in the driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
The STMPE1600 is an I2C based GPIO expander. This initial patch
only supports reading from/writing to the pins on the STMPE1600,
and there is currently no support for interrupts.
Signed-off-by: Titouan Christophe <moiandme@gmail.com>
Introduce a set of header files to be able to define and declare
sections and regions in the linker script. Introduce also DT helpers to
retrieve data back.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add driver for sensirion consumer humidity sensor line.
Supports shtc1 and shtc3, but only shtc3 is tested.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Third generation R-Car series products have up to
seven I2C bus interfaces conformant with the
Philips Semiconductors (now NXP Semiconductors) I2C bus
(Inter-IC bus) specification.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Use GPIO output high and low to simulate I2C start and stop
conditions to restore i2c to normal.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Create the pinmux phandle to the I2C driver node in the
devicetree. When the pinmux_pin_set function in
i2c_it8xxx2_init can refer to the setting of this phandle.
It is more flexible to use.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add single-register MMIO GPIO driver for complex cases where
only several fields in register belong to GPIO lines and each GPIO
line owns a field with different length and on/off value.
Such CREG GPIOs are used in Synopsys em_starterkit and HSDK boards.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
This property has been marked as deprecated in 2.5.0 and was not
actually used for even longer time.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
The nRF QSPI has a configurable delay from the rising
clock signal to the actual sample point measured in
clock cycles. This commit exposes that delay as a DTS
parameter without modifying existing behavior.
Signed-off-by: Abram Early <abram.early@gmail.com>
Add basic support for TI HDC20XX series (e.g. HDC2010, HDC2021, HDC2022,
HDC2080). It is able to get temperature and humidity in the default
14-bit resolution. Triggers, resolution selection, interrupt line, auto
measurement mode are currently not supported.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Nuvoton provides different series MCU. The NPCX series has a specific
id, which can identify the real chip part number. This CL adds soc id
for the NPCX series.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
This commit defines max-erase-time element inside flash-controller
to be part of device tree.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
The PS/2 module in npcx provides a hardware accelerator mechanism
including an 8-bit shift register, a state machine, and control logic
that handle both the incoming and outgoing data. The hardware
accelerator mechanism is shared by 4 PS/2 channels. To support it,
this CL separates the PS/2 driver into channel and controller drivers.
The controller driver is in charge of the PS/2 transaction. The channel
driver is in charge of the connection between the Zehpyr PS/2 API
interface and controller driver.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Move lis2dw12 trigger pulse configurations from Kconfigs to Device Tree.
Moreover the dts properties have been renamed as 'tap', which sounds a
better name to immediately catch the feature behind it. Since tap
threshold cannot be zero, this value (which is the default in dts
binding) is used to enable/disable the device feature per each axis.
The event can be generated on INT1 only.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common binding file that will be included by all bindings
handled by lis2dw12 driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
bits property indicates the number of in-use slots of available slots
for GPIOS. We have a similar property ngpios in gpio-controller.yaml,
we will use ngpios to calculate port_pin_mask. Let's remove bits and
only use ngpios.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Add support for the Xilinx GEM Ethernet controller, which is integrated
in both the Xilinx Zynq and ZynqMP (UltraScale) SoC families. The driver
supports the management of a PHY attached to the respective GEM's MDIO
interface.
This driver was developed with ultimately the Zynq-7000 series in mind,
but at the time being, it is limited to use in conjunction with the
ZynqMP RPU (Cortex-R5) cores. The differences are minor when it comes
to the adjustment of the TX clock frequency derived from the current
link speed reported by the PHY, but for use in conjunction with the
Zynq-7000, some larger adjustments will have to be made when it comes
to the placement of the DMA memory area, as this involves the confi-
guration of the MMU in Cortex-A CPUs.
The driver was developed under the qemu_cortex_r5 target. The Marvell
88E1111 PHY simulated by QEMU is supported by the driver.
Limitations currently exist when it comes to timestamping or VLAN
support and other minor things. Those haven't been implemented yet,
although they are supported by the hardware. In order to be fully
supported by the ZynqMP APU, 64-bit DMA address descriptor format
support will be added.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
This CL introduces six properties, clock-frequency, core-prescaler,
apb1/2/3/4-prescaler in pcc (Power and Clock Controller) node to
configure clock settings. It also removed the original Kconfig options
used for the same purpose.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Convert the keyscan portion of the Holtek HT16K33 driver to adhere to
the kscan API instead of the GPIO API.
When this driver was introduced the kscan API was not present. The
keyscan driver was therefore implemented as a GPIO interrupt driver.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Create the pinmux phandle to the ADC driver node in the
devicetree. When the pinmux_pin_set function in
adc_it8xxx2_channel_setup can refer to the setting of
this phandle. It is more flexible to use.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Since the valid bit-depth of RAM_PDn registers are different, this CL
introduces a 'ram-pd-depth' property in 'nuvoton,npcx-pcc' node if the
application needs to turn off the partial ram blocks for better power
consumption.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add multi-instance support and make use of the stmemsc i2c/spi
read/write routine that has been introduced to simplify the ST
sensor drivers code.
Moreover, move spi-full-duplex property from Kconfig inside Device
Tree, so that each LIS2MDL instance can be configured selectively
in accordance to how it is used in h/w.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add a port property to describe which hardware port a GPIO device node
is describing since we can't tell from the registers (as the registers
are interleaved in the same MMIO space).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change the drivers's compatible from atmel,sam-tc to atmel,sam-tc-qdec.
The atmel,sam-tc should be reserved for the future counter driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
These compatibles don't match the dt-schema regular expression for
compatible properties that we'd like to support in Zephyr because they
do not begin with a letter.
Use linaro, as a vendor prefix to make them compliant. Update the
release notes since out of tree users will need to keep up.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This patch adds a label property to the GPIO LED parent node and fixes
the label property description of the child node. Indeed it is the label
of a parent node which can be used as device_get_binding() parameter to
retrieve the LED device, and not the one of a child node.
In addition, this patch sets both this properties as not required
because they are not.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
This patch adds a label property to the PWM LED parent node and fixes
the label property description of the child node. Indeed it is the label
of a parent node which can be used as device_get_binding() parameter to
retrieve the LED device, and not the one of a child node.
Fixes#34275
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
STM32 internal temperature sensor driver.
This sensor can be used to measure the temperature of the CPU
and its surroundings.
Signed-off-by: Eug Krashtan <eug.krashtan@gmail.com>
Enable FlexSPI NOR flash driver with XIP build options.
Configure FlexSPI pins, update board documentation.
Add FlexSPI NOR flash dts node for mimxrt685_evk.
Enable flash storage by adding partition to dts file.
Using last 1MB for storage, and reserving 63MB for code.
Signed-off-by: Saurabh Jagdhane <saurabh.jagdhane@nxp.com>
Adding Reset and Write-protect pins initialization during AT45 driver
start-up. Usually these pins are driven high when not used.
The AT45 device incorporates an internal power-on reset circuit, so
there is no initial on-off reset sequence.
Signed-off-by: Eug Krashtan <eug.krashtan@gmail.com>
Implementation of the Bosch M_CAN IP driver.
This driver is just the base for a specific SoC implementation.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Added support for GPIO driver for Intel Elkhart Lake
board.
The GPIO driver will support pin value read/write operations,
pin direction and interrupt configuration. ACPI enumeration
support and support for different GPIO communities is also
present.
Verified on ehl_crb.
Signed-off-by: U Divya <u.divya@intel.com>
ADC emulator is designed to be used in tests on native_posix board. It
supports 1-16 bit resolution range and all GAINs from enum adc_gain.
Reference voltages and number of emulated channels are set through dts.
Using special API from drivers/adc/adc_emul.h it is possible to set
constant voltage value returned by given ADC channel or set custom
function which allows to simulate complex output.
Also reference voltages can be changed in runtime using the API.
The CL also includes:
- Add adc definitions of ADC emulator in
tests/drivers/adc/adc_api/src/test_adc.c for supporting test suites.
- Add test for ADC emulator API in tests/drivers/adc/adc_emul/
Signed-off-by: Tomasz Michalec <tm@semihalf.com>
add dts bingings for dma usage
add dts support for adc with edma and hwtrigger
add a periodic_trigger feature to dts
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Renesas has Serial Communication Interface with
FIFO (SCIF) hardware block which allow asynchronous and
synchronous serial communication. The SCIF has 16-stage FIFO
buffers separately for transmissions and reception.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Recently WiFi ESP32 driver (utilizing WiFi radio in ESP32 SoC) was
introduced into drivers/wifi/esp32/ and it already caused confusion as
there was existing drivers/wifi/esp/ directory for ESP-AT
driver (utilizing external WiFi chip, by communicating using AT commands
from any serial capable platform). So question has arisen whether it is
good to merge both, while they are totally different drivers.
Rename ESP-AT driver to be placed in drivers/wifi/esp_at/, so that it is
easier to figure out difference between "esp32" and "esp_at" just by
looking at driver name. Rename also DT compatible and all Kconfig
options for the same reason.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Remove reset pin requirement from devicetree as this
is not required for modem functionality, and is not
used in the driver anyways.
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
The MAX17262 is an ultra-low power fuel-gauge IC which implements the
Maxim ModelGauge m5 algorithm. The IC monitors a single-cell battery
pack and supports internal current sensing for up to 3.1A pulse
current. The IC provides best performance for batteries with 100mAhr
to 6Ahr capacity.
Signed-off-by: Matija Tudan <mtudan@mobilisis.hr>
Add pinctrl-0 as being required on NXP Kinetis DTS bindings for I2C,
FTM, UART, and DSPI related devices.
Other devices like ethernet and CAN are utilized outside of just the
Kinetis family and thus we can not require pinctrl-0 property for them
at this time.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add specific binding for stm32f100 pll which differs from existing
stm32f1 and stm32f105 specific pll binding.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Automatic collision detection for half-duplex mode can be enabled
by setting `collision-detection` proprety for uart hardware
in the dts file. If the transmitted bit does not match the received
bit an error is raised. This is useful in RS-485 half-duplex mode.
Signed-off-by: Arvin Farahmand <arvinf@ip-logix.com>
Add binding fro stm32wl-rcc.yaml that derivates from stm32wb-rcc.
Additionally update stm32wb-pll-clock.yaml to be used as well
for stm32wl series and add missing div-m property.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add clocks node and clocks to stm32l5 series.
PLL binding is reused from stm32l4 series.
Matching binding is updated to document that.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add bindings for F0/F3/G0/G4 clocks.
Introduce new rcc binding "st,stm32f0-rcc" binding
that describes RCC hardware blocks that don't have
"apb2-prescaler".
This binding also applies to G0.
Binding "st,stm32f0-pll-clock" is used for both F0
and F3 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add PLL bindings for STM32F1 devices.
- Main PLL binding for STM32F1 non connectivity lines
- Main and PLL2 binding for Connectivity lines (F105/F107)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The current serial driver uses hard code configuration. Rework driver
to use pinctrl and enable full configuration from device tree.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Add a function that uses the JESD216 SFDP BFP DW16 Enter 4-Byte
Addressing parameter to put the device into 4-byte addressing mode if
one of the entry modes that's supported by the driver is available on
the device.
Perform the transition if SFDP data is provided (either by devicetree
or at runtime), or if a special devicetree property provides the entry
mode descriptor.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This CL adds a override mechanism for pwm module's input clock source
assignment. If the 'clock-bus' property exists, the NPCX_DT_PROP_ENUM_OR
macro function will return an enum upper token value. Otherwise, it
expands to default value in 'clocks' property.
For example, if the users want to select LFCLK as pwm0's input clock,
ths node can be overridden by adding 'clock-bus' property with an enum
string, "NPCX_CLOCK_BUS_LFCLK".
&pwm0 {
status = "okay";
clock-bus = "NPCX_CLOCK_BUS_LFCLK";
};
Signed-off-by: Keith Short <keithshort@google.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Exit latency is the maximum time required by a CPU to transition from
a specific idle state to active state. This information is going to be
used to properly configure the wake up event in order to the system be
able to execute the next scheduled task.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
NPCX PWM supports output buffet select to push-pull or open-drain. Add
output buffer select option 'drive-open-drain' in devicetree for NPCX
PWM. If set, the PWM output will be configured as open-drain. If not
set, defaults to push-pull.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
These changes turn out to have been incompatible with the way pinctrl
drivers are going to work, so we need to go back to what we had before
until we can agree on a better approach.
Squash of the following reverts:
Revert "boards: nrf: fix deprecated I2C properties"
This reverts commit 2a4ac9ac02.
Revert "samples: switch nrf overlays to sda-gpios, scl-gpios"
This reverts commit 01bb08e7d8.
Revert "boards: nrf: switch to sda-gpios, scl-gpios"
This reverts commit 17a66304c4.
Revert "i2c: nordic: switch to phandle arrays for pinmux"
This reverts commit 821c03a14a.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
When 1.8V is disabled, sdhc can only
communicate at low speed. But this can
save the external circuit for switching
between 3.3V and 1.8V, which is very
practical in costdown scenarios.
Signed-off-by: Frank Li <lgl88911@163.com>
Some SPI NOR devices, particularly Atmel and SST, power-up with block
protect bits set in the status register. These bits must be cleared
before any erase or program operation can succeed. However, blindly
clearing bits in SR is wrong as some of these are non-volatile and
control chip behavior, including quad-enable.
Add a devicetree flag to identify device-specific BP bits in the status
register that should be cleared on startup only for devices that need
them, and when set do the clear during initialization.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit is about the it8xxx2 analog to digital converter
driver. Support 8 channels ch0~ch7 and 10-bit resolution.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Fixed the name of nodes in in espi-vw, miwu-wui, and miwu-int
device-tree node. This CL fixed missing nodes in CL d3a94fa8ab.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
For i2c-devices, reg is the address. This took me way to long to
discover and I wanted to leave a breadcrumb for the next Zephyr newbie.
Signed-off-by: Jeremy Bettis <jbettis@chromium.org>
First version of a driver for the st773r LCD controller.
Based on st7789v
Signed-off-by: Kim Bøndergaard <kim@fam-boendergaard.dk>
Signed-off-by: Kim Bøndergaard <kibo@prevas.dk>
Update the binding for how we represent pin data to support child
nodes with a nxp,kinetis-pins property that has the pin data.
For example:
UART0_CTS_PTA0: uart0_cts_pta0 {
nxp,kinetis-port-pins = < 0 2 >;
};
Also pull in pincfg-node.yaml to get various common pin flags like
"bias-pull-up", "drive-open-drain", etc.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fixed the name of nodes in device-tree files by following rules:
If object is 'phandles', use underscores for object name.
If not, such as 'node' or 'property', use hyphens for object name.
This CL also applies normal style for all nodes in npcx device-tree
files.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by lsm6dso driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Currently the MAX17055 driver assumes that a battery matching the
default characteristics is used.
This change allows battery characteristics to be specified in device
tree and writes them to the MAX17055 on initialization.
Existing default values are maintained for backwards compatibility.
Initialization routine taken from MAX17055 Software Implementation
Guide, document UG6365.
Signed-off-by: Hayden Ball <hayden@playerdata.co.uk>
Use a combination of fixed-clock and fixed-factor-clock devicetree
nodes for describing the clock dividers/multipliers of the NXP Kinetis
System Clock Generator (SCG) present in the KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Support single mode operation by enabling it and
making the driver to use the interrupt to findout
when the data is ready for fetch. The sample fetch
will be blocked for a specified maximum time untill
the interrupt happens.
* Make operation mode configurable in DTS file
* Make offset cancellation configurable in DTS file
* Use single common .yaml file for both i2c and spi
* Store above configurations in dev->config_info
Signed-off-by: Masoud Shiroei <masoud.shiroei@assaabloy.com>
This CL introduces the Power Switch Logic (PSL) pads which detect the
wake-up events and turn on/off core power supply (VCC1) for ultra-low
-power consumption in npcx device-tree file.
By adding PSL input-pad objects, psl_in1, psl_in2, and so on, into
'psl-in-pads' property and configuring their 'flag' properties, the
related driver will configure them via soc specific functions later.
For example, if PSL input 1 pad that is plan to detect a 'falling edge'
event, this property should be:
vsby-psl-in-list {
psl-in-pads = <&psl_in1>;
};
And the flag property in psl_in1 should change to
&psl_in1 {
flag = <NPCX_PSL_FALLING_EDGE>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Make sure that child bindings with their own compatibles are treated
as first-class bindings. Do this by making sure that nodes whose
bindings are defined via 'child-binding:' are picked up as bus nodes,
instead of a parent bus node of the same type.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The AN547 is a Soft Macro Model implementation of the SSE-300 subsystem
with Ethos-U55 and Cortex-M55 components targeting the MPS3 board.
The SoC support is based on the AN521 MPS2+ support that already exists
in Zephyr.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial support for the Cortex-M55 Core which is an implementation
of the Armv8.1-M mainline architecture and includes support for the
M‑profile Vector Extension (MVE).
The support is based on the Cortex-M33 support that already exists in
Zephyr.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
UARTs in Nordic devices only support a specified list of baud rates.
Choosing a different baud rate without this patch will cause a runtime
error, whereas with the constraint, this mistake is already found in
dts construction with a useful error message.
Signed-off-by: Peter Niebert <peter.niebert@univ-amu.fr>
This patch includes initial support for FT800 display driver.
It includes basic features. It can be easily extended with more
FT800 display list and co-processor features.
Signed-off-by: Hubert Miś <hubert.mis@gmail.com>
Add support to control DE/nRE RS-485 transceiver signals
over GPIO pins. Useful if the UART controller does not
support RS-485 mode.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add MODBUS RTU (over serial line) subsystem.
MODBUS RTU implementation supports booth server and
client roles. Some components of the implementation are based
on the uC/Modbus stack, which was published under Apache license,
(https://github.com/SiliconLabs/uC-Modbus
fdd1218a28e313c1212fed5ed42e5c65d3056a2c).
Resolves: #2854
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
In NPCX chips, System Configuration module can configure not only
pinctrl but also misc. functionality such as glue and flash write
protection. This change moves the scfg driver from the pinctrl folder
to soc/arm/nuvoton_npcx/common and renames it to avoid confusion.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Adds support for the Texas Instruments FDC2X1X Capacitance-to-Digital
Converter for Proximity and Level Sensing Applications.
Signed-off-by: Igor Knippenberg <igor.knippenberg@gmail.com>
Introduce PSoC-6 pinctrl infraestructure and definitions. This add
files to handle devicetree entries and following modifications:
- add pinctrl bindings
- update gpio bindings with pin-cells
- add pinctrl node and move gpio nodes inside
- declare pinctrl for current uart entries
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Added file with common properties for cortex-m cores.
Added optional swo-ref-frequency property.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add GPIO definitions to QuickLogic EOS S3 devicetree.
Co-authored-by: Jan Kowalewski <jkowalewski@antmicro.com>
Signed-off-by: Wojciech Tatarski <wtatarski@antmicro.com>
Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com>
AArch64 has support for PSCI. This is especially useful for SMP because
PSCI is used to power on the secordary cores.
When the PSCI driver was introduced in Zephyr it was designed to rely on
a very PSCI-centric subsystem / interface.
There are two kinds of problems with this choice:
1. PSCI is only defined for the non-secure world and it is designed to
boot CPU cores into non-secure state (that means that PSCI is only
supposed to work if Zephyr is running in non-secure state)
2. There can be other ways or standards used to start / stop a core
different from PSCI
This patch is trying to fix the original wrong assumption by making the
interface / subsystem a generic one, called 'pm_cpu_ops', and using PSCI
only as an actual driver that is a user of this new interface /
subsystem.
For now the new subsystem is only exposing two methods: cpu_on and
cpu_off, others will probably follow according to the needs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The DMA bindings had duplicate description: keys. Merge the two
descriptions into one to fix the issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Many data items that are represented in a pin configuration node are
common and generic. Pin control bindings should use the properties
defined on a standard way when are applicable; not all of these
properties are relevant or useful for all hardware or binding
structures. Each individual binding document should state which of
these generic properties, if any, are used, and the structure of the
DT nodes that contain these properties.
This is based on Linux, documentation:
https://www.kernel.org/doc/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Conver the NIOS-II mSGDMA driver to be devicetree based. Add node for
dma controller into nios2f.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Deprecate the scl-pin and sda-pin properties in the devicetree.
Provide new scl-gpios and sda-gpios properties instead.
This lets the user specify SCL and SDA like this:
&i2c0 {
scl-gpios = <&gpio0 1 0>;
sda-gpios = <&gpio1 4 0>;
};
Instead of having to use:
&i2c0 {
scl-pin = <1>;
sda-pin = <36>;
};
Provide error checking and understandable error messages for invalid
configurations.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Convert ism330dhcx INT_PIN attribute from Kconfigs to Device
Tree binding properties. Here int-pin has been defined as
enum with two possible values: 1 and 2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert ism330dhcx accel and gyro odr attributes from Kconfigs to Device
Tree binding properties.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Converts ism330dhcx accel and gyro range attributes from Kconfigs to
Device Tree binding properties.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by ism330dhcx driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Change dfe-ant-num propert name to dfe-antenna-num.
The change is conde to keep the same naming style
for all properies, like dfe-pdu-antenna property.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add initialization of GPIOs that are used for antenna switching.
GPIOs provided to DFE extension in Radio peripheral, to drive
antenna switching, should be initialized in GPIO peripheral beforehand.
The initialization is optional and may be disabled by Kconfig.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
In NPCX7 series, it contains two tachometer (TACH) modules that contains
two Independent timers (counter 1 and 2). They are used to capture a
counter value when an event is detected via the external pads (TA or
TB).
The CL also includes:
— Add npcx tachometer device tree declarations.
— Zephyr sensor api implementation for tachometer.
— Enable "tach1" device in npcx7m6fb.dts for testing.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces a kernel device driver implemented by the internal
64/32-bit timers in Nuvoton NPCX series. Via these two kinds of timer,
the driver provides an standard "system clock driver" interface.
It includes:
- A system timer based on an ITIM64 (Internal 64-bit timer) instance,
clocked by APB2 which freq is CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC.
- Its prescaler is set to 1 and provide the kernel cycles reading
without handling overflow mechanism.
- A event timer based on an ITIM32 (Internal 32-bit timer) instance,
clocked by LCLK which frequency is 32KHz and still activated when ec
entered "idle/deep idle" power state for better power consumption.
- Its prescaler is set to 1 and provide timeout event mechansim.
- Compensate system timer which clock is gating for better power
consumption after ec left"idle/deep idle" power state.
This CL passed starve, timer_api, and timer_monotonic test suites.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Modifications to incorporate latest write to new flash area
Modification to avoid writing garbage to new flash area when compactor
is called during init.
Modifications to allow erase at partition size instead of eeprom
pagesize.
Modifications to better separate rambuf usage from flash usage.
Corrected some errors in compactor
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
This driver emulates a EEPROM device in flash.
Reworked implementation with modified flash layout.
The emulation represents the EEPROM in flash as a region that is a
direct map of the eeprom data followed by a region where changes to
the eeprom data is stored. Changes are written as address-data
combinations. The size of such a combination is determined by the
flash write block size and the size of the eeprom (required address
space), with a minimum of 4 byte.
The eeprom page needs to be a multiple of the flash page. Multiple
eeprom pages is also so supported and increases the number of writes
that can be performed.
The eeprom size, pagesize and the flash partition used for the eeprom
are defined in the dts. The flash partition should allow at least two
eeprom pages. For fast read access a rambuffer can be enabled for the
eeprom (by setting the option rambuf in the dts).
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
We've removed the need for label properties from the pinmux devicetree
nodes on all other controllers and its not required for the TI one, so
remove it from the .dts and drop label being required in the binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a simple pinctrl node for the IOF registers under the GPIO
controller node to be used by the pinmux driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add ESPI SAF features to the Microchip eSPI driver as
a separate file. ESPI SAF depends upon the core eSPI
driver adding the ability to attach the system SPI
flash to the EC eSPI endpoint instead of the host
eSPI controller.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
During the driver init, the function will set the sensor resolution
based on the driver's dts variable "resolution"
The driver's device tree has been updated to include the value
"resolution".
The default is set to the highest resolution of 0.0625C.
Moved mcp9808_reg_write from mcp9808_trigger.c to mcp9808.c
This allows resue of the same function in both the trigger and
resolution functions.
Function name changed to xxx_16bit to distinquish it from the 8
bit write function that will added.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
Add support for backup SRAM initialization found in multiple STM32
microcontrollers. Linker script facilities are also provided to make it
easy to define variables in the backup SRAM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Create a common binding file that will be included by all bindings
handled by iis2iclx driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The compatible for the ARMv8 timer should have been arm,armv8-timer and
not arm,arm-timer. The dts binding file name was correct, just the
compatible was wrong. Rename dts, binding, and associated code to use
arm,armv8-timer.
Fixes#31946
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the litex,clk to use the clock-controller.yaml and remove
address-cells/size-cells as they aren't needed for the binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename the SPI/I2C EEPROM devicetree binding to reflect that it only
covers AT24 and AT25 EEPROMs).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The DAC53608 and DAC43608 (DACx3608) are lowpower, eight-channel,
voltage-output, 10-bit or 8-bit digital-to-analog converters (DACs)
respectively. They support I2C with a wide power supply range
from 1.8 V to 5.5 V, and a full scale output voltage range of
1.8 V to 5.5 V. The DACx3608 also includes per channel, user
programmable, power down registers.
Signed-off-by: Matija Tudan <mtudan@mobilisis.hr>
ARM Server Base System Architecture defines Generic UART interface,
which is subset of PL011 UART.
Minimal SBSA UART implementation does not define UART hardware
configuration registers. Basically, only FIFOs and interrupt management
operation are defined.
Add SBSA mode to PL011 UART driver, so it can be used at SBSA-compatible
platforms, like Xen guest.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reworks the NXP FlexSPI device tree bindings to configure controller and
device properties needed for an upcoming FlexSPI flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
There are platforms that have multiple states that maps to a specific
Zephyr power state. To accommodate this sort of situation this commit
adds an additional property to a power state that can be used by the
platform.
The power state now consists of two properties, a category and a
substate-id. The former property is the current power state.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
These need to be gpio controllers and have the necessary specifier
properties for use in gpio specifiers.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
PSoC-6 SoC needs that user define the nvic interrupt number to bind
with the peripheral interrupt line for the Cortex-M0+ CPU. It uses
a multiplex before any NVIC interrupt line. The interrupt vector is
selected using interrupt-parent property with the intmux_chN number
reference.
Note: The PSoC-6 SoC allows that both CPUs receive the same interrupt.
A tipical use is GPIO interrupt handle and user is responsable to
define interrupt line, priority and take care of enable same peripheral
instance on both CPUs only when appropriated.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Add an emulation controller which routes eSPI traffic to attached
emulators depending on the selected chip(mostly host).
This allows drivers for eSPI peripherals to be tested on systems
that don't have that peripheral attached, with the emulator handling
the eSPI traffic.
Signed-off-by: Dawid Niedzwiecki <dn@semihalf.com>
Add the girq and girq-bit fields to the binding. This allows
encoding GIRQ related information inside device tree.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Initial driver and sample application of
TDK Invensense ICM42605 6-axis motion sensor.
This driver provide DTS for nRF52 DK board DTS setting.
Providing features are below.
Sensor data streaming - Accel, gyro
Tap, Double tap triggering.
Set/Get FSR, ODR by set attr API
Support multi instance feature.
Signed-off-by: JuHyun Kim <jkim@invensense.com>
Add radio peripheral to nrf52833 DTS including antenna matrix
congiuration for Direction Finding extennsion.
Add appropriate binding file for nRF radio peripheral.
There is no default antenna matrix configuration. Antennas number
and GPIOS mapping to DFEGPIOS is project specific.
Complete configuration must be provided by end user as overaly.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The ksz8794 yaml file provides information regarding device tree's
properties for this particular DSA switch IC.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Move all PCIe-based DT nodes under a PCIe bus and take advantage of
the DT_ANY_INST_ON_BUS_STATUS_OKAY() and DT_INST_ON_BUS() macros.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The only two supported operations for data caches in the cache framework
are currently arch_dcache_flush() and arch_dcache_invd().
This is quite restrictive because for some architectures we also want to
control i-cache and in general we want a finer control over what can be
flushed, invalidated or cleaned. To address these needs this patch
expands the set of operations that can be performed on data and
instruction caches, adding hooks for the operations on the whole cache,
a specific level or a specific address range.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This commit add support for i2c on imx6sx.
I2C support is based on imx7d and requires NXP HAL.
The Device Tree binding is also changed to better reflect that i2c
driver support both imx6sx and imx7d.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Kconfig allowed selecting any bit in the status register as the QE
bit, and defaulted it to 6. Devices need not require a QE bit at all,
and where JESD216 defines QE bit location the only place in first SR
byte that it can be is bit 6. Further, the code unconditionally wrote
the value 0x40 without respecting configuration of other bits. Some
of those bits control write protection of block-protected areas and
should not be changed.
Remove the Kconfig, instead using the jedec,jesd216-controlled
devicetree property. Allow the driver to recognize whether or not
setting the bit is required, and when it is only use bit 6. Only
update if the setting does not match the configuration.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DW15 provides information on entry and exit from QSPI modes. In
particular, it specifies whether and how the status register must be
updated for this feature.
Add a JESD216 devicetree property for the Quad Enable Requirements
value.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The existing method of testing for any of the first four DT instances
having the pcie property feels a bit clumsy and will get more so when
support for more than four UARTs is added. A much more cleaner way to
do this (and more correct probably as well) is to list any PCIe-based
UART nodes under a pcie bus in the Device Tree hierarchy.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add a binding to represent a PCIe bus. This way PCIe devices can be
ordered under a parent PCIe bus object and make help of DT BUS macros
for conditional code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Part of GPIO pads in npcx series support low-voltage (1.8V) level
detection. In order to introduce this feature, this CL adds a new
NPCX-specific controller property, lvol_io_pads, in devicetree file.
For example, here is devicetree fragment which turn on low-voltage
support of i2c1_0 port.
/ {
def_lvol_io_list {
compatible = "nuvoton,npcx-lvolctrl-def";
lvol_io_pads = <&lvol_io90 /* I2C1_SCL0 1.8V support */
&lvol_io87>; /* I2C1_SDA0 1,8V support */
};
};
Then these pads will turn on 1.8V level detection during initialization.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Firmware implementing the PSCI functions described in ARM document
number ARM DEN 0022A ("Power State Coordination Interface System
Software on ARM processors") can be used by Zephyr to initiate various
CPU-centric power operations.
It is needed for virtualization, it is used to coordinate OSes and
hypervisors and it provides the functions used for SMP bring-up such as
CPU_ON and CPU_OFF.
A new PSCI driver is introduced to setup a proper subsystem used to
communicate with the PSCI firmware, implementing the basic operations:
get_version, cpu_on, cpu_off and affinity_info.
The current implementation only supports PSCI 0.2 and PSCI 1.0
The PSCI conduit (SMC or HVC) is setup reading the corresponding
property in the DTS node.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Move iis2dlpc trigger pulse configurations from Kconfigs to Device Tree.
Moreover the dts properties have been renamed as 'tap', which sounds a
better name to immediately catch the feature behind it. Since tap
threshold cannot be zero, this value (which is the default in dts
binding) is used to enable/disable the device feature per each axis.
The event can be generated on INT1 only.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The IIS2DLPC drdy interrupt can be routed to either INT1 or
INT2 pin. Currently the selection is done by Kconfig configuration.
This commit is instead moving it into Device Tree as 'drdy-int'.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The BBC micro:bit v2 is a mini-computer that has been
designed to make the coding fun and easy to learn.
The micro:bit v2 is completely programmable so you can
easily bring your ideas to life! From making games to
creating music and even controlling robots.
The micro:bit comes with neat hardware such as a 25 LED
display, buttons, in-built speakers, Bluetooth 5 & Mesh
connectivity and sensors for temperature, motion & light.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
This property is required information for extracting PSEL bits relevant
to peripheral pinmux from this node.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add some details to help new users learn how to manage the nodes
for compatibles corresponding to IP blocks on Nordic SoCs.
The focus is on IP blocks where the pinmux is configured in
devicetree. These typically have individual properties for each pin,
like a SCK pin on a SPI peripheral, which correspond directly to a
PSEL register value. These violate the usual devicetree convention of
using a 'foo-gpios <&gpioX ...>' phandle property and work in ways
that only make sense if you understand the underlying register map, so
it's worth explaining them a bit more carefully.
Skip these two bindings, which have no drivers: nordic,nrf-i2s.yaml,
nordic,nrf-pdm.yaml.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
In npcx7 series, the Timer and Watchdog module (TWD) generates the
clocks and interrupts used for timing periodic functions in the system.
It also provides watchdog reset signal generation in response to a
failure detection.
The CL also includes:
— Add npcx watchdog device tree declarations.
— Zephyr watchdog api implementation.
— Add Watchdog definitions for npcx7 series in
tests/drivers/watchdog/wdt_basic_api/src/test_wdt.c for
supporting test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This commit is about the it8xxx2 i2c master driver which
includes six SMBus channels. The enhanced channel i2c3,
i2c4, i2c5 are controller which are designed to support
the I2C protocol.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
In order to ease reuse on other series, set DMA as optional
and use IT if no DMA channel is specified in the qspi node.
Tested on disco_l475_iot1
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Setting clock-frequency as required (the driver does not build without
it) and dropping definitions that are already specified in
i2c-controller.yaml.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Replace few instances of space before colon in the binding files, not
functional, just for coherency.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This patch adds IRQ priority support for SiFive PLIC by device-tree.
Some IRQ sources of plic use Kconfig to set priority of their IRQ.
- AON: no driver
- I2C, SPI, PWM: not use IRQ
- GPIO, UART: default 1
So this patch specifies IRQ priority 1 for all sources.
Currently these drivers (gpio and uart) do not support that they get
and use IRQ priority from device-tree. We need more patches.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
The npcx7m6fb dts defines i2c controller and ports, where the controller
is a property in the port node definition and the device nodes should be
defined as subnodes of the port.
This changes the binding definitions to reflect that, defining the port
as an i2c-controller so that in can inherit sub-nodes for i2c devices,
and the controller as a generic node.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
jedec,jesd216.yaml has properties for any memory device that conforms
to the JESD216 specification. This file at a minimum should be
included in the binding for any driver that interacts with such a
device.
jedec,spi-nor-common.yaml extends jedec,jesd216 with additional
parameters useful for memory devices that are not available from
standard JESD216 parameter tables. This file may be included instead
of jedec,jesd216.yaml if a driver is able to support additional
functionality related to the extended description.
jedec,spi-nor.yaml remains the binding for the Zephyr SPI_NOR driver
alone.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add binding for the Nordic ECB (AES electronic codebook mode
encryption) peripheral and corresponding devicetree nodes for
nRF SoCs that feature this peripheral.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
"st,mem2mem" property is supposed to be limited to dma-v1.
Remove its use in dma-v2 components.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2 versions of DMA hardware blocks could be found across stm32 series.
In order to simplify the handling of matching Kconfig symbols,
make this visible in dts files by creating "st,stm32-dma-v1" and
"st,stm32-dma-v2" and set them accordingly in dtsi files.
Duplicate and update related bindings to reflect that new state.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Create a common binding file that will be included by all bindings
handled by iis2dlpc driver. For now this includes optional drdy-gpios
property and it is shared by the i2c and spi version of the driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds the driver for Omnivision OV7725
Color CMOS VGA Sensor.
The driver currently provides a simple capture
function, the output format only provides
RGB565,640x480.
Signed-off-by: Frank Li <lgl88911@163.com>
Add a new display-inversion property to ili9xxx based display drivers to
send a "Display Inversion ON (0x21)" command during initialization.
This seems to be required for some ILI9xxx based displays to work
correctly, such as BuyDisplay ER-TFT028A2-4 (ILI9341 basd IPS display).
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Define a binding for zephyr,fstab which contains multiple child nodes
each of which identifies a file system type and configuration
parameters and associates it with a fixed partition. The base entry
properties specify the mount point and other generic fs mount options,
while bindings specific to a file system type provide the
configuration parameters necessary to describe the file system.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This change adds support for configurable interrupt capabilities
in the emulated GPIO controller via Devicetree bindings.
Fixes#26477
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
The NPCX SMB modules provides full support for a two-wire SMBus/I2C
synchronous serial interface. Each SMBus/I2C interface is a two-wire
serial interface that is compatible with both Intel SMBus and Philips
I2C physical layer. There are 8 SMBus modules and 10 buses in NPCX7
series.
In NPCX7 series, the SMB5 and SMB6 modules contain a two-way switch to
support two separate SMBus/I2C buses (ports) with one SMB module
(controller) Please refer Section 4.7.2 in the datasheet. In order to
support it, this CL seperates the i2c driver into port and controller
drivers. The controller driver is in charge of i2c module operations
and internal state machine. The port driver is in charge of pin-mux
and connection between Zehpyr i2c api interface and controller driver.
All of modules have separate 32-byte transmit FIFO and 32-byte receive
FIFO buffers. These FIFO buffers reduce firmware overhead during long
SMBus transactions by allowing the Core to write or read more than one
data byte at a time to/from the SMB module.
The CL also includes:
— Add npcx i2c port/controller device tree declarations.
— Zephyr i2c api implementation.
— Add "i2c-0" aliases in npcx7m6fb.dts for i2c test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Convert drivers to use pinmux devicetree node to create pinmux device
object.
On intel S1000 we add 'label' as a required property and set it to
'PINMUX' to match CONFIG_PINMUX_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Currently, the only user of the Designware DMA controller
only needs the channel property. So make dma-cells to be
constant of 1.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add 'label' as a required property for nxp,kinetis-pinmux devices. In
addition we cleanup the kw2xd node labels for the pinmux devices to
match the SoC docs and use 'port' instead of 'pinmux_'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Apart from the previously added pins, nRF21540's GPIO interface includes
also MODE pin. This commit adds it to the relevant binding.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
The nRF21540 radio front-end-module can optionally be controlled by a
SPI interface. Add a binding and property to link the SPI bus
configuration data to the FEM node.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This device is not an ARM MCU, it's a radio front-end module. Based
on existing Linux practice it belongs in net/wireless.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The previous API can't change the sampling-point and only allowed
bitrates that fit the time segments.
The new API allows for shifting the sampling-point and adjusts the
number of time quantum in a bit to all more possible bitrates.
The functions to calculate the timings are moved to the can_common file.
They can be used for all drivers.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
This commit is about it8xxx2 platform device tree.
Add driver's binding files, and one device tree as sample.
Signed-off-by: Cheryl Su <cheryl.su@ite.com.tw>
So far nRF's TIMER was used for generating PWM signal. Add support for
generating PWM based on RTC, which is sourced by 32KHz low frequency
crystal. This allows to use low frequency PWM with much lower power
consumption, because high frequency clock path can be disabled.
Don't support RTC clock prescaler, because maximum 512s period covers
most use cases. This allows to adjust pulse and period cycles to the
fact that CLEAR task event is generated always one LFCLK cycle after
period COMPARE value is reached.
Also update hal_nordic revision, as it contains updated check for PPI
channels conflict when RTC is used to generate PWM.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far 'timer-instance' DT property was the way to configure TIMER which
was used for generating PWM signal. Replace that by using 'generator'
phandle, so we get prepared for supporting RTC instances as PWM signal
generator.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Test macro DT_PROP_BY_PHANDLE_IDX_OR. There are two tests, one when
the property exists and other when the property is not set.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add power state property binding and include this property in cpu.
The pm-state attribute is a enum that matches with enum pm_state right
now the only timing attribute is the minimum residency that is the
minimum time for a power state be worthwhile.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
In order to prevent user turns on the pin-mux of devices has io-pads
unexpectedly, this CL added a new device definition for host uart
device. The pin-mux of host uart interface is enabled only if we set its
status as "okay" in dts file of board folder.
The following npcx7 drivers will meet:
1. Default status property of npcx devices with io-pads such as espi,
pwm, uart, host uart and so on should be "disabled".
2. Switch pin-mux by changing status property to "okay" in dts file of
board folder.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
It is put into interrupt controller since it expands some capabilities
of existing interrupt controllers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
NPCX7 includes a 10-bit resolution Analog-to-Digital Converter (ADC). Up
to 10 voltage inputs can be measured and a internal voltage reference
(VREF), 2.816V (typical) is used for measurement. It can be triggered
automatically in Autoscan mode. Each input channel is assigned a
separate result register, which is updated at the end of the conversion.
The CL also includes:
— Add npcx adc device tree declarations.
— Zephyr adc api implementation.
— Add adc definitions of npcx7 in
tests/drivers/adc/adc_api/src/test_adc.c for supporting test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This adds bindings for the LiteX clock control driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Adding support for Quectel BG95 Modem offloaded driver
to zephyr.
The driver currently implements only the
client side functions of the "socket_op_vtable", and
so cannot be used for cases where Zephyr acts as a
server. Moreover the driver only supports TCP for now.
Looking through the guides, the same driver should be
usable for BG96 (and other modems) except for the modem
boot-up sequence. Hence its named as "bg9x" instead of
"bg95".
Tested extensively with Zephyr acting as MQTT endpoint
and publishing / subscribing data to / from an MQTT
broker.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Add dma-cells property in pl330 dma binding document.
Currently only one integer cell with "channel" name is
added in order for the client to specify channel id
to be used for data transfer out of available channels.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
This commit adds a new driver category for memory controller
peripherals. There is no API involved for now, as it has not been found
necessary for first implementation.
STM32 Flexible Memory Controller (FMC) is the only controller supported
for now. This peripheral allows to access multiple types of external
memories, e.g. SDRAM, NAND, NOR Flash...
The initial implementation adds support for the SDRAM controller only.
The HAL API is used, so the implementation should be portable to other
STM32 series. It has only been tested on H7 series, so for now it can
only be enabled when working on H7.
Linker facilities have also been added in order to allow applications to
easily define a variable in SDRAM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Update nrf21540 DTS to support FEM configuration and update other pins
according to te board datasheet
Signed-off-by: Jakub Pegza <Jakub.Pegza@nordicsemi.no>
Currently there is no binding for RISC-V Core-Local Interruptor.
This patch add a simple binding.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Add Atmel SAM I2C Two-wire Master Interface (TWIM). The SAM
i2c controller have specifics regs depending of operation mode
Master/Slave and the bindings are for Master only.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add devicetree bindings for the Xilinx AXI Timer IP. This timer can
either be used as a counter or as a PWM controller.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Converts fxos8700 magnetic vector magnitude options from Kconfigs to
optional device tree properties.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts fxos8700 power mode options (normal, low noise low power, high
resolution, low power) from Kconfigs to an optional device tree
property.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts fxos8700 range options (2g, 4g, 8g mode) from Kconfigs to an
optional device tree property.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
LIS3DH and LIS2DH12 devices share the same driver with
LIS2DH device. So, the bindings are reusing the same
common structure (as LSM30AGR-ACCEL and LSM303DLHC-ACCEL
devices are already doing)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This adds support for GRLIB GPTIMER general purpose timer used in
LEON3/4/5 systems.
One of the GPTIMER subtimers is used to generate periodic interrutps
for announcing ticks. Another subtimer is used as upcounter for the
cycle_get_32() service.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
This adds support for the GRLIB APBUART UART peripheral commonly used in
LEON3/4/5 systems.
Driver features:
- Auto-detecting debug FIFO, if configured by GRMON
- Setting and getting UART transfer attributes
- Hardware FIFO if available
- Any number of APBUART devices based on devicetree
- Error status indication
- Polled operation
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
This adds support for the GRLIB IRQMP interrupt controller commonly used
in LEON3/4/5 systems.
The driver supports the 15 SPARC interrupts and 16 extended interrupts.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
The number of capture/compare registers available on a peripheral
should be exposed in devicetree.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Make this driver multi-instance and use the new API.
Notes for sensorhub mode:
In case of multiples devices it is possible that some of them
has i2c slaves attached to it (sensorhub mode) but not the
others. Since the driver is configured in the same way for
all the instances (CONFIG_SENSORHUB=y), the routine that initialize
the sensorhub part does not fail anymore in case no slaves
are found for a particular instance. Instead, those non-sensorhub
driver instances will set the shub_inited flag to false and
will totally ignore the feature.
Notes for triggers:
In case of multiples devices the device pin the interrupt wire is
attached to can be different (INT1 or INT2 pin). So, this
information has been moved in DTS and then stored in the
specific instance config structure.
Currently the driver is able to handle a sngle interrupt line
at a time attached to either INT1 or INT2.
MOreover, the interrupt initialization for a driver instance proceed
only if the drdy has been configured in its DT, else it returns ok.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Make driver generic for multiple ILI displays. The adopted strategy is
to share all driver code except register initialization, which has been
found to have some specific registers/values depending on the
controller.
The driver has been adjusted to support multiple compatibles.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add uart bus interface to extended esWIFI driver. This enables all
Inventek modules with IWIN AT Commands firmware.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Add support for configuring Ethernet pins using DT pinctrl entries. Note
that F1 series pinctrl support is not handled as the driver does not
support F1.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Channels 4..7 are multiplexed on adc16. The NXP HAL exposes
ADC16_SetChannelMuxMode but this function is not yet included
in Zephy. The following patch adds channel-mux-b to the dts
enabling the use of the alternate channels of 16 bit adc.
Signed-off-by: Andreas Dröscher <github@anticat.ch>
This provides structure for the regulator device hierarchy and a
driver for GPIO-controlled regulators along with its binding.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This PR follows Linux in defining devicetree content for generic
voltage and current regulators, and an initial driver API for
controlling them.
A regulator itself may depend on a power source, so it needs to
support the properties that enable that power source.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Provide a common set of properties for various ways of controlling
power:
* supply-gpios for a GPIO specifier acting like a switch
* vin-supply for a reference to a regulator device
Document the behavior expected when these properties are present.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The DMA bindings had duplicate description: keys. Merge the two
descriptions into one to fix the issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We aren't using vnd,serial for anything currently. Remove requiring
interrurpts property as that requirement isn't needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Allows the use of pin interrupt and callbacks for pca95xx family
GPIO expander chips with an interrupt line.
Enable config flag and define a gpio pin for the expander interrupt-
line (INT) in devicetree and the driver will accept pin interrupt
configurations for the expander gpio pins.
Level triggering is supported through emulation.
A worker is used to avoid waiting for I2C in ISR.
Example devicetree node:
gpioext0: tca9539@77 {
compatible = "nxp,pca95xx";
label = "GPIO_EXT_0";
reg = <0x77>;
interrupt-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
gpio-controller;
#gpio-cells = <2>;
ngpios = <16>;
};
Fixes: #27561
Signed-off-by: Bent Ove Stinessen <bent@norbit.no>
In fixing up the altera vendor prefix, we forgot to rename the binding
files to match the compatible.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There are a few cases in which "altera" was used instead of "altr" as
the vendor prefix. Update DTS and bindings in those cases to use "altr"
Fixes#29373
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The DMA channel number used for the DMA transfer can now
be specified from the device tree config files
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add power-gpios device-tree binding property to power on module before
communicating with it. This pin is called CHIP_PU in case of ESP32{,-S2}
and CHIP_EN in case of ESP8266. Dedicated reset pin is available only on
the latter, however Espressif recommends (in ESP8266 Hardware Design
Guidelines) to use CHIP_EN instead. Follow those recommendations and use
power-gpios to reset chip if that is provided over device-tree.
Configure power-gpios and reset-gpios as inactive by default, so that
chip becomes ready after executing esp_reset() function, either if one
or both are provided over device-tree.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Most DT bindings use reset-gpios name when there is a pin to reset whole
chip. Rename wifi-reset-gpios to reset-gpios to be more consistent
between various drivers. Additionally this prevents confusion, as
somebody might think that this pin resets only WiFi, which is not true.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The IIS2ICLX is a high-accuracy. ultra-low noise, low-power
two-axis linear accelerometer which can be interfaced through
either I2C or SPI bus.
Its high accuracy, stability over temperature and repeatability
make IIS2ICLX particularly suitable for inclination measurement
for industrial applications (inclinometers).
https://www.st.com/resource/en/datasheet/iis2iclx.pdf
This driver is based on stmemsc i/f v1.03.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Have the driver default to UART_CFG_PARITY_NONE if no parity property
exists rather than using default in binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to pcintrl configuration using pcintrl helper
macros.
Pinctrl init sequence has to be done before bus_mutex initialization.
Driver dts bindings are updated to reflect usage of pinctrl-x
properties
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
* Add comments about the default settings
* Change proximity-trigger default to match POR of 'disabled'
* Added reference to datasheet
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Provide more docs on ngpios and try and clarify the case if there are
holes in the GPIO slot range how ngpios should work.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In npcx7 series, there're 8 Pulse Width Modulator (PWM) modules and each
one support generating a single 16-bit PWM output. A 16-bit clock
prescaler (PRSCn) and a 16-bit counter (CTRn) determine the cycle time,
the minimal possible pulse width, and the duty-cycle steps.
Beside introducing pwm driver for Nuvoton NPCX series, this CL also
includes:
1. Add PWM device tree declarations.
2. Zephyr PWM api implementation.
3. Add aliases in npcx7m6fb_evb board device tree file for supporting
samples/basic/blinky_pwm application and pwm test suites
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add an emulation controller which routes SPI traffic to an attached
emulator. Only one emulator is supported per bus at present, since
chip-selction functionality is not present.
This allows drivers for SPI peripherals to be tested on systems that
don't have that peripheral attached, with the emulator handling the SPI
traffic.
Signed-off-by: Simon Glass <sjg@chromium.org>
In case a "required: False" enum binding doesn't mention a
default value, but a default value makes sense to be set in the code,
DT_ENUM_IDX_OR could be used to provide the default idx to be used.
New macro comes with appropriate tests.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Reused Linux bindings were using /* */ in some property description
fields.
This is not compatible with legacy device tree api which expands
these fields in commented sections of generated file
devicetree_legacy_unfixed.h resulting in compilation issue.
Seen when running tests/lib/devicetree/legacy_api.
Remove /* */ for now, waiting legacy api to be removed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Generalize io-channels and io-channel-names devicetree node properties
and move their definitions to base.yaml. Keep binding specific
description where relevant.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This change allows to use SSD1306 based displays to be used on the
SPI bus as well.
Adding SPI shield.
Tested on SSD1306 and SSD1309 based displays using I2C.
Tested on SSD1309 based display using SPI.
Signed-off-by: Marco Peter <marco@peter-net.ch>
This CL adds more comments for each macro functions used for device tree
file for better explanations. It also changes all hex values in soc.c to
lower case.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This CL contains the drivers of NPCX Host Sub-Modules that serve as an
interface between the Host and Core domains. For most of them, the Host
can configure these modules via eSPI(Peripheral Channel)/LPC by
accessing 'Configuration and Control register Set' which IO base address
is 0x4E as default. And the interrupts in core domain help handling any
events from host side.
In this commit, we introduced six host sub-modules. It includes:
1. Keyboard and Mouse Controller (KBC) interface.
2. Power Management (PM) channels.
3. Shared Memory mechanism (SHM).
4. Core Access to Host Modules (C2H).
5. Mobile System Wake-Up functions (MSWC).
6. Serial Port (Legacy UART)
The tasks in application layer such as 8042, ACPI and host command can
cooperation with this driver by connecting api or callback functions.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
In npcx7 series, all of them support the Intel Enhanced Serial
Peripheral Interface (eSPI) Revision 1.0. This specification provides a
path for migrating host sub-devices via LPC to a lower pin count, higher
bandwidth bus. In addition to Host communication via the peripheral
channel, it provides virtual wires support, out-of-band communication,
and device mastering option over the Chipset SPI flash.
Becisdes introducing eSPI device in npcx7, this CL also includes:
1. Add eSPI device tree declarations.
2. Add npcx7-espi-vws-map.dtsi to present the relationship between eSPI
Virtual-Wire signals, eSPI registers, and wake-up input sources.
3. Zephyr eSPI api implementation.
4, Add OOB (Out of Band tunneled SMBus) support.
5. Add configuration files for eSPI test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Provide yaml bindings for st,stm32f1-pinctrl copmpatible.
It differs from generic stm32 pinctrl bindings on the following points:
- Pinmux "function" parameter: Alternate, General output, Input, Analog
- Pinmux supports an additional "remap" parameter to encode potential
remapping configuration
- Bias configs only apply to input modes
- Drive and speed configs only apply to output modes
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Allow to reconfigure UART baudrate on ESP and on host MCU, so a
non-default baudrate can be used for communication. This option helps
for example to increase network bandwidth without touching ESP chip
firmware.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Move pixel format setting (RGB565/RGB888) to DeviceTree. Add support for
changing pixel format at runtime.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move the devicetree bindings for Analog-to-Digital Converters (ADCs)
from dts/bindings/iio/adc to dts/bindings/adc as Zephyr does not have
an IIO layer.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The host command peripheral device API abstracts how an embedded
controller sends and receives data from a host on a bus. Each bus like
eSPI, SPI, or I2C would implement their own host command peripheral
device. Each hardware device would then handle the necessary hardware
access to send and receive data over that bus.
The chosen host command peripheral device will be used by the host
command handler framework to send and receive host data correctly.
Signed-off-by: Jett Rink <jettrink@google.com>
The SX126x supports using DIO2 to control an TX switch, but only if
the switch can be operated using a single control signal. Add support
for RF switches that are wired to a GPIO instead of the radio chip
itself. This makes it possible to use RF switches that require two
control signals (one for the RX port and one for the TX port) by
wiring them to two GPIOs on the MCU.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Add sector-size property to at45.yaml binding.
Different at45 flash memories have different sector sizes.
Signed-off-by: Marin Jurjevic <marin.jurjevic@hotmail.com>
Add devicetree support to specify bias-pull-up, bias-pull-down, and
drive-open-drain for pin configuration.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instantiate RTT UART instances from devicetree nodes instead of from
Kconfig symbols. While RTT is implemented using software, not hardware,
it is emulating a hardware device, and thus should be configured through
devicetree. This allows the simulated UART device to be selected via
devicetree aliases and chosen nodes.
The following devicetree snippet will instantiate RTT channels 0 and 2
as UART devices.
```
/ {
rtt0: rtt_terminal {
compatible = "segger,rtt-uart";
label = "rtt_terminal";
status = "okay";
};
rtt2: rtt_secondary {
compatible = "segger,rtt-uart";
label = "rtt_app_specific";
status = "okay";
};
};
```
Fixes the RTT portion of #10621.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add an emulation controller which routes I2C traffic to attached
emulators depending on the I2C address selected. This allows drivers
for I2C peripherals to be tested on systems that don't have that
peripheral attached, with the emulator handling the I2C traffic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This CL configures the UART wake-up event triggered from a falling edge
(START condition) on CR_SIN pin. It also includes:
1. Introduce wui_maps property in yaml file to present relationship
between Wake-Up Input (WUI) and UART device.
2. Implement wake-up mechanism by MIWU api functions.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add gpio support for Nuvoton NPCX series. This CL includes:
1. Add GPIO device tree declarations.
2. Introduce wui_maps property in yaml file to present relationship
between Wake-Up
Input (WUI) and 8 IOs belong to the device.
3. Zephyr GPIO api implementation.
4. GPIO callback functions implementation with MIWU api functions.
5. Overlay file for gpio basic tests
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The device Multi-Input Wake-Up Unit (MIWU) supports the embedded
controller (EC) to exit 'Sleep' or 'Deep Sleep' power state which allows
chip has better power consumption. Also, it provides signal conditioning
such as 'Level' and 'Edge' trigger type and grouping of external
interrupt sources of NVIC. The NPCX series has three identical MIWU
modules: MIWU0, MIWU1, MIWU2. Together, they support a total of over 140
internal and/or external wake-up sources.
In this CL, we use device tree files to present the relationship bewteen
MIWU and the other devices in different npcx series. For npcx7 series,
it include:
1. npcx7-miwus-int-map.dtsi: it presents relationship between MIWU group
and NVIC interrupt in npcx7. Please notice it isn't 1-to-1 mapping.
2. npcx7-miwus-wui-map.dtsi: it presents relationship between input of
MIWU and its source device such as gpio, timer, eSPI VWs and so on.
This CL also includes:
1. Add MIWU device tree declarations.
2. MIWU api function declarations and implementation to configure signal
conditions and callback function mechanism. They can be be classified
into two types. One is for GPIO which connects original gpio callback
implemetation and the other is for generic devices such as timer,
eSPI, and so on.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The driver utilizes the CONFIG_NET_OFFLOAD setting to avoid the
normal handling of IP packets, and instead uses a socket-like
UART interface to handle incoming and outgoing data via AT commands.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
This commit adds a node for the ASMedia 2364 controller that acts as an
I2C master on the I2C0 bus. This node contains the GPIO used by the MCU
to notify the ASM2364 that data are available to read.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This patch adds a DTS binding for the Texas Instruments LP5030 and
LP5036 I2C LED controllers. They are respectively providing up to 30
and 36 channels (i.e. 10 or 12 RGB LEDs).
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
The led-controller DT binding gathers some common properties for LED
controllers and for the LED child nodes.
One notable property is "color-mapping" which allows to define a channel
to color mapping for multicolor LEDs.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
By default the I2C timing (I2C_TIMINGR register) of I2C V2 peripheral is
computed depending on clocks at runtime with relatively low precision.
This optional property allows to provide a list of pre-computed values
(typically computed from STM32CubeMX SW tool) instead of using runtime
algorithm.
The precomputed value is only valid for a given clock configuration and
I2C speed setting, so this valid configuration is provided with each
value entry.
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
The spi_flash_w25qxxdv driver has been superseded by the generic
spi_nor driver for over a year. The only non-refactoring change to
the W25Q driver in the last 18 months was done to support a backport
to 1.14.
All devices supported by spi_flash_w25qxxdv driver are expected to be
supported by the spi_nor driver, using the standard `jedec,spi-nor`
devicetree compatible. No in-tree devicetree files make use of this
driver.
Remove the confusion about which driver to select by removing the
unmaintained redundant driver.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
As a general rule devicetree properties should correspond to hardware
description or configuration. In cases where a Zephyr driver receives
instance-specific configuration data from a devicetree property that
property should be marked as being Zephyr-specific. Rename
concat-buf-size to zephyr,concat-buf-size to follow this guideline.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The Nordic TWIM peripheral generates a start condition for each bus
transaction. Devices such as the SSD1306 display and some NXP sensors
can only tolerate the presence of a start condition and device address
after a stop condition. Those devices will not operate correctly when
these signals are observed while the bus is already active. This
motivated the addition of a RAM buffer into which message fragments
could be collected so TWIM can transmit them without injecting
unnecessary start conditions.
However many I2C devices interpret these signals as a repeated start
and ignore them and so function properly without a buffer
concatenating the message fragments.
There is no default for the concat-buf-size property, and the previous
strict requirement for one when performing scatter/gather I/O
transactions broke working drivers for devices that tolerate the
repeated starts. Allow those drivers to work by respecting the
property description and attempting to concatenate messages only if a
buffer in which to place them has been provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Added support for hardware flow control in EFM32 UART driver.
Signed-off-by: Timo Dammes <timo.dammes@lemonbeat.com>
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Use the new SFDP infrastructure to read the supported erase type sizes
and commands from the Basic Flash Parameters block. This removes the
need for explicit reference to most block sizes from this driver.
We're also seeing devices where the page size is not 256 bytes.
Accommodate them.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
With SFDP support we no longer need to get the JEDEC ID or device size
from devicetree. Make them optional in drivers that have been
converted to support SFDP. When runtime SFDP is not enabled the
presence of the required properties will be verified at build-time.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Allow the devicetree binding for a jedec,spi-nor device to provide the
device capabilities by encoding the Serial Flash Discoverable
Parameters Basic Flash Parameters table in the devicetree node. This
supports applications where a specific flash device will be used and
runtime discovery of device capabilities is not desired.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add IUART driver based on MCUX SDK. This driver is used to provide
serial console support on i.MX8M Mini SoC.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Add devicetree bindings for the Xilinx AXI GPIO v2 IP. This GPIO
controller has an optional "GPIO2" port, which is not always present.
The Xilinx specific devicetree property names and their meaning match a
subset of what can automatically be generated based on the FPGA logic
design using https://github.com/Xilinx/device-tree-xlnx. These
properties are also used by the Linux kernel.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Change the documentation for the arm,dtcm (Data Tightly Coupled Memory)
to reflect that it is not specific to the Cortex-M7 (but also present
on e.g. the Cortex-M1).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add pin controller support for Nuvoton NPCX series
Add pin-mux controller support for Nuvoton NPCX series.
This CL includes:
1. Add pin controller device tree declarations and introduce alt-cells
to select pads' functionality.
2. Add npcx7-alts-map.dtsi since the mapping between IO and controller
is irregular and vary in each chip series.
3. Add nuvoton,npcx-pinctrl-def.yaml and its declarations to change all
pads' functionality to GPIO by default.
4. Pinmux controller driver implementation.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add clock controller support for Nuvoton NPCX series. This CL includes:
1. Add clock controller device tree declarations.
2. Introduce clock-cells in yaml file clock tree to get module's source
clock and turn off/on the its clock
3. Clock controller driver implementation.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The FT5336 driver has been improved and generalized so that multiple
Focaltech touch controllers can be supported using the same single
driver. According to specifications the following list of controller
variants should be supported: FT5x06, FT5606, FT5x16, FT6x06, Ft6x36,
FT5x06i, FT5336, FT3316, FT5436i, FT5336i and FT5x46.
Tested using ER-TFTM028-4 display module (FT6X06).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The EFR32MG21 uses a different kind of clock for watchdogs.
It requires an additional peripheral-id parameter in the dts to get the
proper clock as it is based on the watchdog's ID i.e., cmuClock_WDOG#.
Signed-off-by: Steven Lemaire <steven.lemaire@zii.aero>
This commit enables support for parsing 'fixed-link' node when it
is added to node described in 'ethernet,fixed-link.yaml'.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch adds description for 'fixed-link' node in ethernet DTS
node. It supports setting speed and duplex.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds the device tree nodes and bindings for the I2C
controllers of the LPC11U6X MCUs
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This commit adds basic support for the clock controller used in
lpc11u6x MCUs.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
This commit adds a bindings for the clock controller used in lpc11u6x
MCUs. It also adds a clock-controller node for the lpc11u6x soc series.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This patch adds the DT nodes and binding for the pinmux registers,
aka IOCON (I/O control), found on the LPC11U6x MCUs.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Add support for wsen-itds 3-axis accel sensor, provides acceleration,
temperature data reading and supports configuring of output data rate,
operating mode and scale.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
The parameters for this fuel gauge depend on the hardware design and
the expected battery. These should not be defaulted to a value that
may be inappropriate. Require that they be explicitly provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add Xplained-Pro header connector defined by Atmel. This allows
hardware with compatible headers to define the related GPIOs.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add Xplained header connector defined by Atmel. This allows hardware
with compatible headers to define the related GPIOs.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add support to STM IIS2DH the ultra-low-power highperformance
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add option to concatenate i2c transfers. If concatenation buffer size is
provided then transfers will be concatenated as long as there is space
left in buffer.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
compatible = "arm,cortex-m33f" was already used for some time
(lpc55S6x, nrf9160...) without any related bindings.
Every works fine until you need to access one CPU node property
(eg. clock-frequency)...
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Add device tree bindings for the Semtech SX1261 and SX1262
radios. These will be used by Zephyr's LoRa drivers.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Adds optional device tree properties to set delays between spi chip
select assert/deassert and clock edges in the mcux dspi and lpspi
drivers. If these properties are not set, then the minimum supported
delays are used.
Verified that tests/drivers/spi/spi_loopback/ still passes on
mimxrt1050_evk (lpspi driver) and frdm_k64f (dspi driver).
Measured with a scope that the pcs-sck-delay and sck-pcs-delay times on
the first spi transaction in the test are reduced from 7.82 us to 20 ns
on mimxrt1050_evk.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add Nuvoton numicro series UART support, currently supports
only poll mode.
UART0 clock and pincontrol are directly configured, will be
replace when clock and gpio support is added.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
The SAM0 Timer/Counter for Control Applications can act as a counter
or generator. Add a binding for the TCC in PWM mode and helper to
check the compat mode.
Signed-off-by: Michael Hope <mlhx@google.com>
The value of a label property isn't really the name of an API. It's
the name of a device, as passed to device_get_binding().
Let's just say that directly so people know what this means in
practice instead of what's currently used as the description, which is
harder to understand and not really accurate.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
RF SPDT switches used for RX/TX selection have often power enable pin
connected to MCU's GPIO, so it is possible to disable it to save power
when not doing any data transfers. Add 'antenna-enable-gpios' property
to support such designs.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add support for TCXO power control using GPIO pin. Some boards
(including B-L072Z-LRWAN1 already supported in Zephyr) need delay
applied after powering on TCXO, so add device-tree property allowing to
configure that as well. Cache information about TCXO power status, so
subsequent requests to enable it will not result in unnecessary delays.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There are several antenna path designs on SX1276 compatible boards in
the wild. B-L072Z-LRWAN1 board has dedicated enable pins for RFI, RFO
and PA_BOOST. This is exactly what this patch allows to
configure. Second variant of antenna selection is done with a single
GPIO pin, which controls RF SPDT switches (input or output). This is
also supported, when either 'rfo-enable-gpios' or
'pa-boost-enable-gpios' property is provided alone (RFO/PA_BOOST is
selected only when transmitting, so there is no need for explicit
'rfi-enable-gpios' configuration).
Drop requirement for 'power-amplifier-output' DT property when there is
either 'rfo-enable-gpios' or 'pa-boost-enable-gpios' configured. Fail
using BUILD_ASSERT() when neither is specified.
Make the SX1276SetAntSw() logic similar to loramac-node examples
implementation, so RFO/PA_BOOST is enabled only in
RFLR_OPMODE_TRANSMITTER.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
PA selection mainly depends on board design. So it looks like
device-tree is a better mechanism than Kconfig in this case. Use string
property with two possible values: "rfo" and "pa-boost".
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
With addition of flash_get_parameters API call, it is needed to provide
support for the API to flash drivers.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Add support for the polarity flag in the STM32 PWM driver.
STM32 boards using PWM have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Appropriate WS can be loaded automatically if
the display controller has integrated temperature
sensor or an external sensor is connected.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
- Support PLL for Higher Frequencies 80,160,240 MHz
- Support XTAL Frequencies 26MHz, 40MHz
- Clock Driver can't be disabled, because all of the other drivers
will depend on it to get their operating Frequency based on chosen
clock source (XTAL/PLL).
- Add needed references to BBPLL i2c bus ROM functions.
- Add `rtc` node to Device Tree.
- Since All Peripherals Frequency is depending on CPU_CLK Source,
`clock-source` property added to CPU node
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Cleaned up flow control configuration. Added support for using only
cts or only rts.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Adds a new LPTIM binding for stm32 soc,
based on the timer binding. This will makes a specific filter
on dt_compat_enabled("stm32,lptim")
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add test cases that verify various bits and pieces of the legacy
devicetree macros match the new APIs.
Writing these test cases without giving rise to deprecated macro
warnings which might break people's CI if they build with -Werror
requires turning off the __WARN() generation in
devicetree_legacy_unfixed.h. The entire file is deprecated at this
point and must be explicitly enabled with an opt-in Kconfig option, so
there isn't any harm in doing this.
Nevertheless, take a minimally invasive approach to avoiding __WARN()
generation in gen_legacy_defines.py, to avoid the possibility of
breakage. This code is basically frozen anyway, so hacks like this
won't cause maintainability problems since it isn't being actively
maintained.
Use the new tests as fodder for a migration guide from the old API in
the documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
At some point, "child-binding:" apparently only worked up to 2 levels
deep. That's not the case anymore, but add a regression test to make
sure that doesn't break. 3 levels deep ought to be enough for anyone.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add the missing node and bindings. This is a secure-mapped peripheral,
so do not add it to the common include file
nrf5340_cpuapp_common.dtsi.
Fixes: #25493
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Allow configuring the clock prescaler divider for the NXP Kinetis
FlexTimer. Setting the prescaler to a lower value allows for much
higher resolution/accuracy for the generated PWM waveforms.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The macro iterates through the list of child nodes in a DT_DRV_COMPAT
instance and invokes provided macro for each node.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add definition of zephyr,random-mac-address property that conveys to a
driver to utilize a random MAC address if the driver supports this
feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add infineon XMC4 series UART support. Driver supports
only poll mode using XMCLib.
Out of 4 available UART's on SoC, only UART1 is confgired
by default in UART mode until GPIO & pinctrl support.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
The label property does not need to have its type set
explicitly to string, so remove it.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
By this commit USB audio class implementation is introduced
to Zephyr.
The Zephyr USB audio device class follows bellow
documentations:
- Universal Serial Bus specification rev2.0 (usb20.pdf)
- Universal Serial Bus Device Class Definition for Audio Devices
(audio10.pdf)
- Universal Serial Bus Device Class Definition for Audio Data Formats
(frmts10.pdf)
- Universal Serial Bus Device Class Definition for Terminal Types
(termt10.pdf)
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Add a disk access driver for the stm32 sdmmc component. The driver is
based around the stm32 cube HAL and uses the blocking API.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Add initial support for Broadcom Viper SoC.
It has ARM Cortex-M7 and Cortex-A72 cores.
Signed-off-by: Arjun Jyothi <arjun.jyothi@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Add initial support for Decawave DW1000
IEEE 802.15.4-2011 UWB transceiver.
Driver has basic functionality. Additional functions such
as reading out timestamps and delayed TX were implemented
for test purposes, but also require support in the 802154
subsystem.
Register, sub-register, and defaults defines in the file
ieee802154_dw1000_regs.h are taken from the Decawave's
DW1000 driver for the Mynewt OS.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Binding used for LPC random number generator hardware.
Describes RNG device node in LPC5xxx SoCs device tree peripherals.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Convert i2s_sam_ssc driver to utilize devicetree. We replace Kconfig
options for specifying the DMA configuration (channel, DMA device name)
with getting that from devicetree. We also get pincfg from devicetree,
however we still have Kconfig sybmols to specify if the RF or RK pin is
enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sam_xdmac driver to utilize devicetree. As part of the
controller binding we specify that dmas should contain a channel and the
perid for the DMA transaction.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The DS3231 is an I2C real-time clock with internal temperature
compensated oscillator, maintaining civil time to 1 s precision with
nominal 2 ppm accuracy from 0-40 Cel.
The basic functionality is exposed as a counter that is always running
at 1 Hz. Much more functionality is exposed as driver-specific API,
including the ability to translate between the time scale of the DS3231
and the time scale of the Zephyr uptime clock. This allows correlation
of events in the system clock to UTC, TAI, or whatever time scale is
used to maintain the DS3231.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add a driver that can handle several instances of AT45 family chips,
which are enabled by specifying DT nodes for them with the "compatible"
property set to "atmel,at45" and other required properties like JEDEC
ID, chip capacity, block and page size etc. configured accordingly.
The driver is only capable of using "power of 2" binary page sizes in
those chips and at initialization configures them to work in that mode
(unless it is already done).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This header is physically related to the Adafruit Feather, but uses a
different pin numbering and exposes a slightly different set of pins.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The TPM (Timer/PWM Module) is a 2- to 8-channel timer which supports
input capture, output compare, and the generation of PWM signals to
control electric motor and power management applications.
This patch adds the driver and the binding necessary for instantiating
the driver. The work is based on the RV32M1 driver for TPM done by
Henrik Brix Andersen. A later patch will enable this driver to be used
for the KW41Z SoC, if PWM support is requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
This patch introduces the periph to/from memory dma transfer
using the dmamux feature and define new values
for dma cells on client side
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Reworked sam_gmac driver to get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from soc_pinmap.h that are no longer needed due to
getting all that information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This includes the dma cells as client for the spi
An example of the client part is defined in the dma.yaml
Consequently, bindings for the dmas property becomes then 'not required'
Including dma.yaml is not needed as dma properties
are now part of base.yaml
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree.
We add a property ('calib-offset') for the SAM{D,E}5x family of SoCs
that is the bit position offset from ADC0 BIASCOMP in the NVM Software
Calibration Area Mapping. For ADC0 this is typically 0 and for ADC1
this will be 14.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In STM32 can driver CAN2 instance need to know the base address
of CAN1 instance which is referenced as master can.
Add this information as an optional property to stm32 can binding.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add local-mac-address on DT and enable it on rf2xx driver. If user
define local-mac-address this value will be used as default mac address.
Otherwise driver automatically add a random mac address.
On application level user can change default mac address using net_mgmt
command with NET_REQUEST_IEEE802154_SET_EXT_ADDR parameter defined on
include/net/ieee802154_mgmt.h header.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree. Move the prescaler setting
from Kconfig to devicetree as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add clock references for ADC and TC devices. Update the bindings for
these devices to require clocks property and update the dtsi files to
have the clock info.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-spi binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-i2c binding for dma to replace the dma property with
proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM SPI device. We update the SPI
binding to have pinctrl-0 bindings that are expected to have
at least phandles for MISO, MOSI, and SPCK, but might also have
various chip selects as well.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We update sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Reworked adc_sam_afec driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-uart binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the atmel,sam0-dmac binding under the dma binding dir and add
cell information for channel and trigger source. Update the associated
dtsi files to match these changes.
This is in prep of ATMEL SAM0 SERCOMM devices like UART, I2C, and SPI to
user proper 'dmas' property to specify the dma info to use.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the GCLK, MCLK, and PM clock controllers. Add bindings
and devicetree nodes associated with these clock controllers. Also add
clock references for the SERCOM peripheral set to allow those drivers
(i2c, spi, uart) to utilize this information.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM TWI and TWIHS I2C devices. We update
the TWI and TWIHS I2C bindings to have pinctrl-0 bindings that are
expected to have 2 phandles to the TWCK & TWD pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We update sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We've had clocks in base.yaml but didn't have clock-names. Add it to
base.yaml with similar functionality to interrupt-names, reg-names, etc.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
enable the interrupt functionality for sx1509b gpio expander,
when the CONFIG_GPIO_SX1509B_INTERRUPT config is enabled.
The gpio pin used for interrupt should be configured in the
device tree sx1509b node before enabling the interrupt
configuration.
Signed-off-by: Viraaj Somayajula <sviraaj@zedblox.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DAC (digital to analog converter) peripheral driver with a generic API
suitable for most MCUs (only basic DAC features considered).
Signed-off-by: Martin Jäger <martin@libre.solar>
Add pinctl support for the SAM UART and SAM USART devices. We update
the UART and USART bindings to have pinctrl-0 bindings that are expected
to have 2 phandles to the RX & TX pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We add sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The atmel,pins property will be utilized to describe pin mux
configuration. The property will be a phandle-array in which the
phandle points to the given GPIO port the pin is on, the pin number, and
the mux configuration.
This change updates the atmel,sam-gpio binding to support that
phandle-array and updates the associated SoC dtsi files as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add dts support for the headers on Adafruit Feather boards.
This will allow adding FeatherWing boards as shields.
Signed-off-by: Richard Osterloh <richard.osterloh@gmail.com>
This add the following options to GMAC device tree bindings:
- max-frame-size
- max-speed
- phy-connection-type
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
dmas and dma-names properties could be used by a wide range
of potential dma client, hence put them in base.yaml, as
optional properties.
Since current stm32-i2s driver implementation only support
dma, set these properties as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a property to the openisa,rv32m1-gpio binding that relates the GPIO
node to the pinmux PORT node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Updated the openisa,rv32m1_vega-pinmux binding to require the label
property and updated the rv32m1.dtsi to add label properties for the
pinmux nodes.
Also update gpio_basic_api test to use DT_NODELABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The flexcomm peripheral on lpc socs can be configured into uart, spi,
i2c, or i2s mode. Introduce a shared device tree binding that gets
included by the more specific driver type bindings.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The st,stm32l0-flash-controller did not have a binding, add one for it.
Also made a comment in stm32l0.dtsi that the driver doesn't currently
support this controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Group all the GPIO controllers under a pinctl node so that we have a
container for pinmux configuration data.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds i2c device tree bindings and nodes for the lpc54xxx and lpc55s6x
socs in preparation for adding a new i2c driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
With the introduction of the new device-tree macros it is now possible
to use the settings for speed and flow-control from the bus node instead
of having the same properties on the esp node itself.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Make the label property required for "arm,cmsdk-gpio" compatible
nodes. Update binding to mark the 'label' property required and updated
associated .dts files to add a 'label' property if it didn't exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a YAML, DTS node and driver support to utilize data from devicetree
for register address and driver name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
And implement DT_ANY_INST_ON_BUS() in terms of it.
This makes some error messages quite a bit shorter by avoiding
UTIL_LISTIFY(), which has a nasty temper and tends to explode if not
treated gently.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The label property of the fixed-partitions child binding was duplicated
with two different values. This is invalid yaml, but went unnoticed by
pyYAML. Removed first entry to preserve value produced by pyYAML
behavior of overwriting duplicates.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Added properties to support the core interrupt controller on the NIOS2
cpu cores and enable that support for the NS16550 UART.
We rename some compatibles so that the cpu core compatibles is unique.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree binding for the NXP Kinetis Low Power Timer (LPTMR)
module. This module can either act as a 16 bit counter or a 16 bit
pulse counter.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This adds the DTS binding for the CAVS Intra-DSP Communication (IDC)
driver for the DSP on Intel SoC.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert the driver to use DT_INST_ defines, update all dependent dts,
soc and board files.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This is joint work with Kumar Gala (see signed-off-by).
Add helper macros which abstract the "true names" of each of the four
types of node identifier we intend to support (e.g. DT_ALIAS(),
DT_INST()).
These can be passed to a new DT_PROP() macro which can be used to read
the value of a devicetree property given a node identifier from one of
these four other macros, and the as-a-c-token name of the property.
Add other accessor macros and tests as well.
Add some convenience APIs for writing device drivers based on instance
numbers as well. Drivers can "#define DT_DRV_COMPAT driver_compatible"
at the top of the file, then utilize these DT_INST_* macros to access
various property defines.
For example, the uart_sifive driver can do:
#define DT_DRV_COMPAT sifive_uart0
Then use DT_INST macros like:
.port = DT_INST_REG_ADDR(0),
.sys_clk_freq = DT_INST_PROP(0, clock_frequency),
For convenience working with specific hardware, also add:
<devicetree/gpio.h>
<devicetree/adc.h>
<devicetree/spi.h>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is useful for devicetree documentation, examples, and tests,
where we need to put something for the vendor but we can't use an
actual piece of hardware for some reason.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The `xlnx,ttcps` binding, despite having the file name of
`xlnx,ttcps.yaml`, had the compatible property of `cdns,ttc`.
While it is true that the Xilinx ZynqMP platform embeds the Cadence
Triple Timer Counter (TTC) IP core, its TTC differs from the original
Cadence core in that it implements 32-bit counters, instead of the
16-bit counters defined in the original; hence, the Xilinx variant is
not compatible with the original Cadence version and should be treated
as a different device.
This commit changes the `xlnx,ttcps.yaml` compatible property to
`xlnx,ttcps` for the above reasons.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This adds support for the Espressif ESP8266 and ESP32 devices to be used
as peripherals on a UART.
There are two main AT command versions that can be selected, 1.7 and
2.0. Since they behave a bit different it is important to select the
one that matches the used in the firmware on your device.
When downloading large amounts of data it is highly recommended to
enable CONFIG_ESP_PASSIVE_TCP and flow control on the UART so that
data is not lost due to UART speed or receive buffer size.
Currently unsupported:
- Changing UDP endpoint with a sendto()
- Bind to a specific local port
- Server socket operations, ie listen() and accept()
Official AT firmware for ESP8266 and ESP32 can be found at:
https://github.com/espressif/esp-at
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
The IIS2MDC is a 3D digital magnetometer ultra-low power sensor
for industrial applications, which can be interfaced through
either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2mdc.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Extended nrf_uart driver to support TX only.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add entropy driver based on GECKO TRNG module along with device
tree support for EFM32PG and EFR32MG SOCs.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
The ISM330DHCX is a ultra-low power IMU with a 3D digital accelerometer
and 3D digital gyroscope tailored for Industry 4.0 applications, which
can be interfaced through either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add a property to the nxp,kinetis-gpio binding that related the GPIO
node to the pinmux PORT node.
For the kl25z we add the pinmux nodes as well since they didn't exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Introduction of tachometer device nodes for the Microchip
MEC1501 SOC. In addition, dts bindings for are also introduced.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Add the girq and girq-bit fields to the binding. This allows
encoding GIRQ related information inside device tree.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The max-value should just be an int and not an array. Change the type
to 'int' in the binding and fixup the driver to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert pms7003 sensor driver to utilize device tree.
DTS would look something like the following for the pms7003:
uart {
pms7003: pms7003 {
status = "okay";
compatible = "plantower,pms7003";
label = "pms7003";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ak8975 sensor driver to utilize device tree.
This also supports the ak8975 embedded in a invensense MPU9150. In such
a case the device tree node should look something like, where the ak8975
is a child of the mpu9150.
mpu9150@68 {
compatible = "invensense,mpu9150";
reg = <0x68>;
label = "mpu9150";
#address-cells = <1>;
#size-cells = <0>;
ak8975@c {
compatible = "asahi-kasei,ak8975";
reg = <0xc>;
label = "ak8975";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This adds a simple binding for the Cadence Tensilica Xtensa LX4
CPU. File originally from the LX6 binding.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Convert to support devicetree.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>