Implement UART firmware download driver for NXP
BT module.
Only support Murata 2EL M.2 module on RT1170EVKB.
And only one instance can be supported now.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Convert ST7789V display driver to use MIPI DBI API. This commit also
updates in tree boards to use the new devicetree syntax needed to enable
this display with the MIPI DBI API.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix compilation error when reset-gpios is enabled.
Undefined reference to dev_cfg variable.
Reset gpio duration needs to be defined, but is not in binding file.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
`irq0-channels` defines even-numbered channels as the default value.
Since 6 was dropped from this definition, it is added.
Also, since the maximum number of channels is 12,
remove the ones that are exceeded.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Convert the slz_hci.c HCI driver to use the new HCI driver API. This also
fixes the HCI bus type to correctly indicate VIRTUAL instead of UART.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Convert the hci_nxp.c HCI driver to use the new HCI driver API. Also move
the driver binding under dts/bindings/bluetooth, like all other HCI driver
bindings.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Convert the hci_stm32wba.c driver to the new HCI API. Unlike in most cases,
the devicetree node is already enabled on the SoC level (rather than board
level). This is in order to mirror how the Kconfig option was originally
enabled, i.e. on the SoC level.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Convert the spi.c and hci_spi_st.c drivers to use the new HCI driver API.
Both drivers are converted in one go since one derives from the other's
devicetree binding.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Update the native controller to the new HCI driver API. The devicetree
node is placed under existing `radio` nodes, which seemed like the most
intuitive option.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Convert the H4 driver to the new HCI driver API. This includes updating
also any boards that use the driver, i.e. adding the appropriate
devicetree node and chosen property to them.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Add a base binding for Bluetooth HCI drivers. All HCI drivers should
extend this binding (through an include directive) to create their own
binding files.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Add a shield for NXP ov5640 camera modules. This shield uses a 44-pin
board-to-board connector which is supported on NXP RT1170 and RT1160 EVKs.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
nxp,unique-mac actually is not meant to be universally
unique, the LAA bit should therefore be set, and fix the
description of the property in the binding to clarify
the intended usage of this property.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Added a single instance lptmr node on the
mcxn947 soc dts. Updated counter lptmr to
have max value property.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
This driver can be used for both mcux and
s32k series SoCs which have flexio IP.
PWM channel is automatically allocated by
flexio driver based on the available timers.
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Fix KSZ8081 binding properties:
- reset-gpios and interrupt-gpios are generally standard
properties and therefore should not be using a special name
- mc, is not the correct vendor prefix for microchip
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This commit should address the #73803 issue
where the DMA node does not provide support
for the #dma-cells binding. Peripherals should
specify one or more DMA channels via the dmas
and optionally dma-names DT properties.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Declare power state constraints for a device in devicetree.
It allows a map between device instances and power states that disable
their power. This information is used by a new API
(pm_policy_device_power_lock_put/get) that automically set/release
pm state constraints.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add driver for Realtek RTL8211F 10/100/1000M ethernet PHY.
This driver implements vendor specific behaviour like
detecting link state change by GPIO interrupt, which is not
present in the generic MII driver.
Fixes: #66348
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
- Added nxp,enet1g compatible to distinguish between ENET (nxp,enet)
and ENET_1G (nxp,enet1g) peripherals within the same driver.
- Added config ETH_NXP_ENET_1G to enable 1G mode of operation on ENET_1G.
- Support RGMII mode of connection between MDIO and PHY to be
able to work with ENET_1G peripheral and support 1000M speed.
- Removed performing of PHY reset before configuring link - it is
not desirable for RTL8211F PHY connected to ENET_1G on RT1170.
Reset of other PHYs can be performed by PHY driver itself if required.
Fixes: #66348
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add option for RGMII connection type between the MAC and the PHY
device into the ethernet controller binding.
Fixes: #66348
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Introduce driver for ov7670 camera, supporting QCIF,QVGA,CIF, and VGA
resolution in YUV and RGB mode.
Support was verified on the FRDM-MCXN947, using the SmartDMA camera
engine, which is enabled in the following PR:
https://github.com/zephyrproject-rtos/zephyr/pull/72827
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The byteSENSI-L is a fun LoRa device based on nRF52 MCU that integrates
many sensors.
Signed-off-by: Rico Ganahl <rico.ganahl@bytesatwork.ch>
Signed-off-by: Guy Morand <guy.morand@bytesatwork.ch>
Configure the quad-spi in DualFlash Mode
This property of the stm32 boards will access simultaneously
two identical quad-flash external memories connected to
2 quad-spi banks (pins).
Dual Flash Mode is possible on stm32 series with QUADSPI_CR_DFM
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add devicetree nodes for the Reset Information registers on nRF54H20,
along with a new binding.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Introduce the stm32h7RS serie to the clock_controller,
based on the stm32h7 clock driver
Datasheet DS14359 rev 1 gives CPU max freq of 500MHz
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce the stm32h7RS serie to the clock rcc controller,
and the exti interrupt controller based on the stm32h7 rcc bindings.
Three PLL clocks are available.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the property of drive-strength to drive a high or low current
selection. If this property is not configured, it is the default
setting. According to the SPEC, the default drive current selection
varies from different pins.
Define the high level 0b: 8mA
low level 1b: 4mA or 2mA
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add bindings for nxp display interfaces. These bindings describe the 6
and 40 pin FPC connectors used for displays on several NXP EVKs using
gpio nexus nodes.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add DT binding for stm32 PWR peripheral that controlls wake-up pins.
This binding primarily introduces wake-up pins configuration in
a unifed way that takes into consideration the variations between
STM32 SoC series & facilitates the association of GPIO pins with
their corresponding wake-up pins.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Deprecate the CAN controller bus-speed/bus-speed-data properties and rename
them to bitrate/bitrate-data to match the terminology used in other CAN
devicetree properties and the CAN subsystem API.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Make it possible to disble device power management individually per
power state. This allows targets tuning which states should
(and which should not) trigger device power management.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
I chose this approach instead of software rotation because I need it for
an ultra low power project.
Rotation in steps of 0, 90, 180, 270 degrees is done by changing
the data entry modes.
This commit removes the orientation-flipped property as it is redundant.
I made the assumption that the current driver implementation is right
about controller X/Y versus display width/height. The display controller X
parameter matches with the display height (dts) and display controller Y
parameter matches with the display width (dts). It looks like display
manufacturers choose to have it like this because a wider screen probably
makes more sense.
Tested on the reel_board with a 250x122 display (ssd1673 controller)
and a custom PCB with a 200x200 display (ssd1681 controller).
Also tested all orientations with various width/height dts overrides.
Signed-off-by: Sven Depoorter <svndepoorter@gmail.com>
This add basic support for the STM32 Digital Temperature Sensor found
notably on the STM32H7 series. It work in interrupt mode and support
basic power device management.
It does not support the more advanced features like using the
temperature threshold, triggers from LPTIM or using the LSE clock in
during sleep or stop.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Improve the binding descriptions for the atmel,at24 and atmel,at25 EEPROM
compatibles. These compatibles work for a number of different EEPROM
families manufactured by vendors other than Atmel.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fix a compilation error occurring when a prescaler was set for ADC on F1
and F3 family.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add support for the IS31FL3194 3-channel LED driver. This driver can be
configured to handle its outputs as either a single RGB LED or (up to)
three independent LEDs.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
The native Linux CAN driver supports CAN FD. Change the binding to reflect
this. No functional changes.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The CAN loopback driver supports CAN FD. Change the binding to reflect
this. No functional changes.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This is a soc/board integration for the MediaTek Audio DSP device on
the MT8195 SOC, along with a Zephyr mtk_adsp soc integration that will
work to support similar 8186 and 8188 device shortly.
A python loader (similar to cavsload.py) is included that will run in
developer mode on current chromebooks (an HP x360 13b-ca000 was
tested) with an unmodified kernel.
Signed-off-by: Andy Ross <andyross@google.com>
Add an interrupt controller driver for this device. This is an
extremely simple second level controller with per-interrupt-bit
registers for "enable" and "status". There is no internal latching,
so no "clear/ACK" process is needed.
Signed-off-by: Andy Ross <andyross@google.com>
Refactored vendor-specific duplicates of uart tx/rx invert properties
into a common dts file uart-controller-pin-inversion.yaml
Signed-off-by: Anuj Pathak <anuj@croxel.com>
This WDT is responsible for monitoring the external
32.728 Hz crystal connected to pins XTAL_32K_P and
XTAL_32K_N. If an oscillation failure is detected
the hardware automatically switch to RTC_RC_SLOW
clock source and triggers an interrupt.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Add a parameter to allow the configuration of the number of address
bytes used by the I2C master. This allows the driver to expose larger
buffer sizes.
Tested with standard linux at24 driver.
Signed-off-by: Bram Vlerick <bram.vlerick@openpixelsystems.org>
Behavior of "force"-mode as described in datasheet cannot be achieved if
low-power mode is enabled. After triggering a sampling, the sensor will
not sample again for the period specified in measurement-time.
Signed-off-by: Juliane Schulze <juliane.schulze@deveritec.com>
Driver did not work on ESP32c3, by specifying pin to be output and
input solve the issue. Improve documentation, to highlight that driver
is requiring open-drain support.
Signed-off-by: Fredrik Gihl <fgihl@hotmail.com>
Rename nxp,kinetis-lptmr compat to nxp,lptmr.
Because of concerns over breaking downstream users,
keep support for the old compatible temporarily and
make it clear it should be changed.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Some Ambiq Apollox Blue SOC (e.g. Apollo3 Blue) uses internal designed
BLEIF module which is different from the general IOM module for SPI
transceiver. The called HAL API will also be independent. This driver is
implemented for the BLEIF module usage scenarios.
Signed-off-by: Aaron Ye <aye@ambiq.com>
The RTC subsystem in espressif's SOCs, among other tasks
is responsible for clock selection for CPU and for low
power domain clocks such as RTC_SLOW and RTC_FAST.
This commit allows for proper clock source and rate
selection for CPU, using the espressif,riscv and
espressif,xtensa-lx6/7 bindings.
It also enables clock selection for RTC_FAST and RTC_SLOW,
that impacts some peripherals, such as rtc_timer.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
The MBOX driver interface expects a device tree property '#mbox-cells'
which is not known by the IPM driver. This causes build problems when
both drivers are given for a single shared DT node.
To fix this problem for this driver specifically, add a dummy
'#mbox-cells' property to the bindings of the STM32 HSEM IPM driver.
This does not affect any other IPM driver, and the STM32 HSEM IPM driver
is still functioning with this dummy property.
Signed-off-by: Celina Sophie Kalus <hello@celinakalus.de>
Add a device tree binding for the new driver. Since there already
exists an IPM driver using the unsharable hardware semaphore interrupt,
the new driver is not added to any boards or SOCs per default to avoid
compatibility problems. See #37300 for the IPM driver.
Signed-off-by: Celina Sophie Kalus <hello@celinakalus.de>
Add support for the memory controller by utilizing QSPIC2. The latter is
capable to drive both NOR and PSRAM memory devices. For this to work,
the RAM driving mode is enabled.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Add bindings for NXP MIPI CSI-2 Rx which is a MIPI CSI-2 receiver
connecting a camera sensor to the NXP CSI.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
TLC59731 is a 3-Channel, 8-Bit, PWM LED Driver with
TI Single-Wire interface (EasySet) protocol.
Signed-off-by: Javad Rahimipetroudi <javad.rahimipetroudi@mind.be>
Convert the ST7735R display to use the MIPI DBI API. Boards and overlays
using this display are also updated.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Include reset device binding in some of the NXP LPC
IP bindings to be able to add the resets property.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add binding representing the peripheral reset controller
of the NXP LPC SYSCON heritage hardware including SYSCON
itself and the newer RSTCTL.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Clarify that there needs to be a cell named "id" in order
to be usable by the reset controller macros.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
