Deprecate the scl-pin and sda-pin properties in the devicetree.
Provide new scl-gpios and sda-gpios properties instead.
This lets the user specify SCL and SDA like this:
&i2c0 {
scl-gpios = <&gpio0 1 0>;
sda-gpios = <&gpio1 4 0>;
};
Instead of having to use:
&i2c0 {
scl-pin = <1>;
sda-pin = <36>;
};
Provide error checking and understandable error messages for invalid
configurations.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add the girq and girq-bit fields to the binding. This allows
encoding GIRQ related information inside device tree.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Move all PCIe-based DT nodes under a PCIe bus and take advantage of
the DT_ANY_INST_ON_BUS_STATUS_OKAY() and DT_INST_ON_BUS() macros.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This commit add support for i2c on imx6sx.
I2C support is based on imx7d and requires NXP HAL.
The Device Tree binding is also changed to better reflect that i2c
driver support both imx6sx and imx7d.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Add some details to help new users learn how to manage the nodes
for compatibles corresponding to IP blocks on Nordic SoCs.
The focus is on IP blocks where the pinmux is configured in
devicetree. These typically have individual properties for each pin,
like a SCK pin on a SPI peripheral, which correspond directly to a
PSEL register value. These violate the usual devicetree convention of
using a 'foo-gpios <&gpioX ...>' phandle property and work in ways
that only make sense if you understand the underlying register map, so
it's worth explaining them a bit more carefully.
Skip these two bindings, which have no drivers: nordic,nrf-i2s.yaml,
nordic,nrf-pdm.yaml.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This commit is about the it8xxx2 i2c master driver which
includes six SMBus channels. The enhanced channel i2c3,
i2c4, i2c5 are controller which are designed to support
the I2C protocol.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Setting clock-frequency as required (the driver does not build without
it) and dropping definitions that are already specified in
i2c-controller.yaml.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Replace few instances of space before colon in the binding files, not
functional, just for coherency.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The npcx7m6fb dts defines i2c controller and ports, where the controller
is a property in the port node definition and the device nodes should be
defined as subnodes of the port.
This changes the binding definitions to reflect that, defining the port
as an i2c-controller so that in can inherit sub-nodes for i2c devices,
and the controller as a generic node.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The NPCX SMB modules provides full support for a two-wire SMBus/I2C
synchronous serial interface. Each SMBus/I2C interface is a two-wire
serial interface that is compatible with both Intel SMBus and Philips
I2C physical layer. There are 8 SMBus modules and 10 buses in NPCX7
series.
In NPCX7 series, the SMB5 and SMB6 modules contain a two-way switch to
support two separate SMBus/I2C buses (ports) with one SMB module
(controller) Please refer Section 4.7.2 in the datasheet. In order to
support it, this CL seperates the i2c driver into port and controller
drivers. The controller driver is in charge of i2c module operations
and internal state machine. The port driver is in charge of pin-mux
and connection between Zehpyr i2c api interface and controller driver.
All of modules have separate 32-byte transmit FIFO and 32-byte receive
FIFO buffers. These FIFO buffers reduce firmware overhead during long
SMBus transactions by allowing the Core to write or read more than one
data byte at a time to/from the SMB module.
The CL also includes:
— Add npcx i2c port/controller device tree declarations.
— Zephyr i2c api implementation.
— Add "i2c-0" aliases in npcx7m6fb.dts for i2c test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add Atmel SAM I2C Two-wire Master Interface (TWIM). The SAM
i2c controller have specifics regs depending of operation mode
Master/Slave and the bindings are for Master only.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Provide a common set of properties for various ways of controlling
power:
* supply-gpios for a GPIO specifier acting like a switch
* vin-supply for a reference to a regulator device
Document the behavior expected when these properties are present.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert driver to pcintrl configuration using pcintrl helper
macros.
Pinctrl init sequence has to be done before bus_mutex initialization.
Driver dts bindings are updated to reflect usage of pinctrl-x
properties
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add an emulation controller which routes I2C traffic to attached
emulators depending on the I2C address selected. This allows drivers
for I2C peripherals to be tested on systems that don't have that
peripheral attached, with the emulator handling the I2C traffic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add gpio support for Nuvoton NPCX series. This CL includes:
1. Add GPIO device tree declarations.
2. Introduce wui_maps property in yaml file to present relationship
between Wake-Up
Input (WUI) and 8 IOs belong to the device.
3. Zephyr GPIO api implementation.
4. GPIO callback functions implementation with MIWU api functions.
5. Overlay file for gpio basic tests
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This commit adds a node for the ASMedia 2364 controller that acts as an
I2C master on the I2C0 bus. This node contains the GPIO used by the MCU
to notify the ASM2364 that data are available to read.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
By default the I2C timing (I2C_TIMINGR register) of I2C V2 peripheral is
computed depending on clocks at runtime with relatively low precision.
This optional property allows to provide a list of pre-computed values
(typically computed from STM32CubeMX SW tool) instead of using runtime
algorithm.
The precomputed value is only valid for a given clock configuration and
I2C speed setting, so this valid configuration is provided with each
value entry.
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
As a general rule devicetree properties should correspond to hardware
description or configuration. In cases where a Zephyr driver receives
instance-specific configuration data from a devicetree property that
property should be marked as being Zephyr-specific. Rename
concat-buf-size to zephyr,concat-buf-size to follow this guideline.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The Nordic TWIM peripheral generates a start condition for each bus
transaction. Devices such as the SSD1306 display and some NXP sensors
can only tolerate the presence of a start condition and device address
after a stop condition. Those devices will not operate correctly when
these signals are observed while the bus is already active. This
motivated the addition of a RAM buffer into which message fragments
could be collected so TWIM can transmit them without injecting
unnecessary start conditions.
However many I2C devices interpret these signals as a repeated start
and ignore them and so function properly without a buffer
concatenating the message fragments.
There is no default for the concat-buf-size property, and the previous
strict requirement for one when performing scatter/gather I/O
transactions broke working drivers for devices that tolerate the
repeated starts. Allow those drivers to work by respecting the
property description and attempting to concatenate messages only if a
buffer in which to place them has been provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit adds the device tree nodes and bindings for the I2C
controllers of the LPC11U6X MCUs
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
Add option to concatenate i2c transfers. If concatenation buffer size is
provided then transfers will be concatenated as long as there is space
left in buffer.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-i2c binding for dma to replace the dma property with
proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the GCLK, MCLK, and PM clock controllers. Add bindings
and devicetree nodes associated with these clock controllers. Also add
clock references for the SERCOM peripheral set to allow those drivers
(i2c, spi, uart) to utilize this information.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM TWI and TWIHS I2C devices. We update
the TWI and TWIHS I2C bindings to have pinctrl-0 bindings that are
expected to have 2 phandles to the TWCK & TWD pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We update sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The flexcomm peripheral on lpc socs can be configured into uart, spi,
i2c, or i2s mode. Introduce a shared device tree binding that gets
included by the more specific driver type bindings.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds i2c device tree bindings and nodes for the lpc54xxx and lpc55s6x
socs in preparation for adding a new i2c driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This adds I2C bitbang driver for LiteX SoC builder with its bindings.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add property for specifying the bus idle timeout for the NXP
i.MX/Kinetis LPI2C I2C controller.
Enabling the bus idle timeout helps the controller to recover from
e.g. EMC causing false clock pulses/spikes on the SCL line.
Without a timeout the LPI2C controller will assume that another bus
master took over the I2C bus and thus refuses to issue a I2C START
condition.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The arc_iot.dtsi used "intel,qmsi-ss-gpio" and "intel,qmsi-ss-i2c"
compatiables, however we have no drivers for these and it seems wrong
that the ARC platform would utilize such compatiables. Remove the
compatiable fields for now (proper one's can be added when there are I2C
and GPIO drivers for this platform).
Also remove the binding files associated with "intel,qmsi-ss-gpio" and
"intel,qmsi-ss-i2c" as nothing in tree utilizes them.
Fixes: 19227
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instead of
child:
bus: foo
parent:
bus: bar
, have
child-bus: foo
parent-bus: bar
'bus' is the only key that ever appears under 'child' and 'parent'.
Support the old keys for backwards compatibility, with a deprecation
warning if they're used.
Also add 'child/parent-bus' tests to the edtlib test suite. It was
untested before.
I also considered putting more stuff under 'child' and 'parent', but
there's not much point when there's just a few keys I think. Top-level
stuff is cleaner and easier to read.
I'm planning to add a 'child-binding' key a bit later (like 'sub-node',
but more flexible), and child-* is consistent with that.
Also add an unrelated test-bindings/grandchild-3.yaml that was
accidentally left out earlier.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
For quite a few peripherals that are currently supported by nrfx HALs
or drivers there are no definitions of corresponding CMSIS-Core
peripheral accessing symbols that would provide their base addresses
in the proper domain (secure or non-secure), accordingly to the build
target. This commits adds devicetree nodes for these peripherals so
that their base addresses can be used in definitions of the accessing
symbols mentioned above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
* Add "#address-cells" and "#size-cells" to base.yaml as properties
that can exist on any node. Cleanup other bindings that inherit
from the base.yaml.
* Add "status" property with an enum of valid options.
* Add "interrupt-parent" to base.yaml. It's a phandle to the node
which is the interrupt controller for the interrupt.
* Add "interrupt-extended" to base.yaml. Provides a way to specify
an interrupt-parent and specifier in a single property. Useful if
a device has multiple interrupts in which different interrupts go
to different interrult controllers.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In most cases #<FOO>-cells should be a constant. For example in spi
controller #address-cells should be 1, and #size-cells should be 0.
Use the const attribute to specify such single known values. Add const
value to missing bindings which have cells.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The port_sel property had the category set to 'define' which isn't a
valid option. Change it to be 'required'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A number of dts bindings mark 'interrupts' as a required property when
in fact they are not for those devices. Remove the 'required' setting
and just have 'interrupts' as 'optional'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Setting it seems rare. Maybe it could be changed to required on just
some platforms (!including bindings can change 'optional' to
'required').
Fixes a bunch of errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Expose MEC1501 5 I2C/SMB controllers
Add Microchip specific I2C device tree properties
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
This adds a SERCOM I2C driver for SAM0 series chips.
Tested with a SAMD21 chip on a SSD1306 display and a MLX90393
sensor. Only compile tested for SAMD20 and SAMR21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add driver and device tree binding for the Low Power Inter-Integrated
Circuit (LPI2C) controllers found in the RV32M1 RI5CY SoC.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
After commit 'scripts/dts: Never ignore properties in
generate_node_defines()', pointless entries for 'interrupt-names'
properties show up in generated_dts_board.conf and
generated_dts_board_fixups.h, because many bindings specify
'generate: define' for 'interrupt-names'.
If 'generation: define' is taken as "generate #define's for this
particular property", then only the 'interrupts' property ought to have
'generation: define'. Having it on both 'interrupts' and
'interrupt-names' makes you wonder what it would mean to only have it on
one of them.
Things get a bit confusing since 'interrupt-names' is still used when
determining the macro names generated for 'interrupts', but it's
probably best to have 'generation: define' work in a consistent way
still (and never be a no-op).
Remove 'generation: define' from all 'interrupt-names' bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Driver for the I2C peripheral in the SiFive Blocks RTL
Repository (https://github.com/sifive/sifive-blocks).
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The Silicon Labs EFR32MG12P Mighty Gecko MCU includes:
* Cortex-M4F core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* integrated Sub-GHz and/or 2.4GHz radio
* multiple low power peripherals
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Endre Karlson <endre.karslon@gmail.com>
The 'id' field was never used and tended to just have the compat of the
node. Lets remove it and removed some code in extract_dts_includes.py
related to it. Added a warning if 'id' is set in a yaml so we can
remove it going forward.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add 'generation: define' directive to 'compatible' property.
When existing for a type of device, move compatible property
description in device base structure (eg: i2c.yaml)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the RDC (Resource Domain Controller) peripheral
permissions settings for the i.MX applications cores (Cortex A9 on
i.MX6 and Cortex A7 on i.MX7).
This will enable both Linux (on application's core) and Zephyr (on M4
core) to share the peripherals and coexist.
The settings are defined at devicetree level and applied in the soc.c.
A complete solution should involve the SEMA4 to control the peripherals
access and prevent resource deadlocking and misusage.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
SDA and SCL pins can now be configured through DTS.
Pins on development kits have been assigned according to arduino
headers.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
* add gpio, i2c, spi definitions
* optimize and bug fix the dts.fixup
* optimize and bug fix the em_starterkit related definitions
in dts folder
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Added device tree support to the ARM SBCon I2C controller. We utilize
the compatiable "arm,versatile-i2c" the binding from Linux for the some
peripheral block.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This was validated on the cc3220sf_launchxl board
using the Zephyr thermometer sample program
adapted to call the i2c driver directly, and fetching
samples from the on-board TMP006 temperature sensor.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Provide generic yaml description for i2c-devices such as sensors
New yaml binding category 'parent/child' is added.
It aims at binding two types of related node such as bus master and
bus slave.
In case of i2c-device object, parent property is 'bus' with value 'i2c'.
In the mean time, i2c node gets child property bus. Master and slave bus
values should match.
As such, 'i2c' node is bus master and 'i2c-devices' nodes are bus slaves
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
According to yaml syntaxic rules, 'properties' described in dts
bindings yaml files could be seen as 'mapping'(key/value couple),
instead of 'series' (list of single elements).
yaml 'mappings' will then be converted by yaml python library as
python 'dict' which will ease treatment (instead of current list
as were before this commit).
Same treatment is applied to 'inherits'.
script extract_dts_inlcude is updated to take change of yaml_list
structre into account. This allows some code simplification. Largest
impact is yaml_collapse function which works now allow complete
overload method on all the attributes of a yaml nodes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Moved yaml files to be under dts/bindings and have the bindings try
and match the linux doc device tree binding dir structure as the
canonical binding reference.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
