This commit aligns TWIM shim to utilize memory-region property.
The memory-region is not required property that enables user
to specify placement of dma buffers in memory region.
It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
Add some details to help new users learn how to manage the nodes
for compatibles corresponding to IP blocks on Nordic SoCs.
The focus is on IP blocks where the pinmux is configured in
devicetree. These typically have individual properties for each pin,
like a SCK pin on a SPI peripheral, which correspond directly to a
PSEL register value. These violate the usual devicetree convention of
using a 'foo-gpios <&gpioX ...>' phandle property and work in ways
that only make sense if you understand the underlying register map, so
it's worth explaining them a bit more carefully.
Skip these two bindings, which have no drivers: nordic,nrf-i2s.yaml,
nordic,nrf-pdm.yaml.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
For quite a few peripherals that are currently supported by nrfx HALs
or drivers there are no definitions of corresponding CMSIS-Core
peripheral accessing symbols that would provide their base addresses
in the proper domain (secure or non-secure), accordingly to the build
target. This commits adds devicetree nodes for these peripherals so
that their base addresses can be used in definitions of the accessing
symbols mentioned above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
