1) Replace master/slave in API for new terms in eSPI spec 1.5
2) Reflect eSPI VW change and macro changes across eSPI drivers
3) Update terms in eSPI driver sample and eSPI test driver
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
MEC172X series SoCs share most IP but the -LJ series expands the PWM and
ADC channels available as well as defines extra pinctrl pins.
Separating these better to be able to simplify their inclusion and
driver code. Any board based on either the -SZ or -LJ package can just
include the mec172x<sz/lj> dtsi files for their specific package.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Removed extra #includes at top of files. Missed closing } of
mec172xnlj.dtsi. Lower-cased 'reg' field of PWMs.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Change device tree VW routing to a form allowing overrides.
Add two new DT optional properties for specifying the reset
source and reset value of each virtual wire. Only virtual
wires that are enabled using the status property are modified.
NOTE: eSPI virtual wires are controlled in groups of 4 by
hardware. The optional reset signal source properties applies
to all four virtual wires in the group. If this field is
changed from the hardware default, it should be changed for
only one virtual wire in the group. If the property exists
in more than one wire in the group it must be set to the
same value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Modify Mircrochip MEC172x eSPI driver to get eSPI virtual wire
hardware routing from device tree.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
update MEC172x adc driver to support device PM.
Implement pm resume and suspend actions to put adc
pins in proper state for suspend and resume.
Notify kernel of busy when adc sampling is in progress.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove the test clock out Kconfig from SoC level. Instead use
device tree PINCTRL entry with updated clock control driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Two issues:
- The nsmi_gpio107 node is being defined twice with the same pinmux
property value. This is an error when compiling the file with dtc.
Zephyr's dtlib doesn't currently error out on this, but it will soon.
Fix this by removing one of the redundant definitions.
- The eeprom_clk_gpio117 node label is referring to a node named
gpspi_clk_gpio117, which is already defined in the same file, but
with a different pinmux property value. This looks like a clear
copy/paste error causing invalid pinmux settings for the
gpspi_clk_gpio117 node.
Fix it by aligning the node name with the node label to create
a separate node with its own pinmux value.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
In order to bring consistency in-tree, migrate all dts code to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
All DT nodes end up being part of the generated 'devicetree_unfixed.h'
header, wether they are referenced or not. The number of entries in that
file can grow quickly when using pre-generated pinctrl nodes.
Considering <devicetree.h> (file uncluding devicetree_unfixed.h) is used
in lots of places nowaday, not using /omit-if-no-ref/ can lead to
increased build times.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
MEC172x eSPI driver, eSPI pin programming, interrupt updates related
to eSPI and other updates for MEC172x eSPI driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
