If the systick period is < 5ms the clock testcase will
stall.
Added a note to warn whoever hits it.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added possibility to reconfigure CONFIG_SYS_CLOCK_TICKS_PER_SEC
for the native_posix board (before it could only be 100)
+
Fixed tickless idle support
+
Minor fixes in irq wrapping
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Due to a security advisory released on February 1st 2018[1], it's
advisable to update mbedTLS to 2.7.0.
The vulnerability, identified as CVE-2018-0488 and CVE-2018-0487, risk
remote code execution when truncated HMAC is enabled or when verifying
RSASSA-PSS signatures.
[1] https://tls.mbed.org/tech-updates/security-advisories/mbedtls-security-advisory-2018-01Fixes: #6025
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
to_read is the minimum value between I2C_ESP32_BUFFER_SIZE
and (msg.len - 1) rather than the maximum value.
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
When I2C Master writes to slave on CMD_Controller, opcode WRITE
was set twice instead of 1 WRITE at the beginning of the
transmission.
And when Master reads from slave, on CMD_Controller,
byte_num = 1 + data_lenght instead of byte_num = 1 at the
beginning of the transmission.
Note that is for 7 bits addresses, to 10 bit adressess is added
more 1 in byte_num as can be seen in the code above this fix.
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
Since PINMUX_INPUT_ENABLED == 1 and PINMUX_OUTPUT_ENABLED == 0,
we can not set a gpio port as input and output at the same time,
So we always set the gpio as input. Thus, the gpio can be used on
I2C drivers for example.
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
MinnowBoard has an uppercase "B" in its name. Also added a link to the
config option mentioned.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The introduction of device tree support sensors need to update the
dts.fixup file in build_all to make sure that we still build.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added a label for soc-nv-flash nodes. Made some updates to the
generation to maintain creating defines for properties like
erase-block-size and write-block-size so they we get both
FLASH_ERASE_BLOCK_SIZE and FLASH_${LABEL}_ERASE_BLOCK_SIZE (same for
WRITE_BLOCK_SIZE).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds app_pad and priv_stacks to the rw section list so that
tests which validate the sections found in the binary pass when run on
systems which contain MPUs.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
It is faster to operate directly on flash_area pointer instead
of fetch it all the time using the fcb flash area id.
Also as f_area_id was needed only for get appropriate flash_area
pointer, so it is better to pass it only while initialization
the fcb and not store it in fcb instance data at all.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
fcb sectors description switch from using array of flash_area
structures to array of flash_sector structures.
This patch aligns tests to this change.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Previously flash_area structure was the parameter for the callback
function for transferring sector location info.
Now flash_sector is used so relevant flash_area is missing for
the callback.
This patch introduces structure fcb_entry_ctx which incorporates
entries' location and relevant flash area. It is used to pass complete
information to the callback. Additional pointer to the flash_area fcb
speeds up operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Prior to this commit: `struct fcb` contained a pointer to an array of
`struct flash_area`. Each entry in the array represented a flash sector
that the fcb comprised.
After commit: `struct fcb` contains a pointer to an array of `struct
flash_sector`, not `struct flash_area`.
Rationale: The FCB needs to know which sectors it occupies for its
rotate operation. However, the `flash_area` type is meant to represent
a collection of sectors, not a single sector. `struct flash_area`
contains information that the fcb does not need (e.g., area ID and
device ID). Furthermore, the flash_map API provides a means of
converting a flash area ID to an array of sectors
(`flash_area_get_sectors()`), but no way to convert to an array of
areas.
Signed-off-by: Christopher Collins <ccollins@apache.org>
Remove thread from memory domain API (k_mem_domain_remove_thread())has
only one argument which is thread ID as per the implementation whereas
documentation says there has to be two arguments, memory domain and
thread ID.Memory domain argument is not required as a thread belongs
to single memory domain at any point in time. Also memory domain
initialisation function (k_mem_domain_init()) should accept only 3
arguments i.e, memory domain name, number of parts and array of
pointers to the memory domain, instead of 4.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
The I2C address of vl53l0x are write in hex, but the VL53L0X_I2C_ADDR
type is int.
Fix this by replace "int" with "hex".
Signed-off-by: Ding Tao <miyatsu@qq.com>
NATIVE_POSIX_STDIN_CONSOLE and NATIVE_POSIX_STDOUT_CONSOLE have more
than one prompts, this will cause warnings when run kconfig checks.
Remove one of two prompts.
Signed-off-by: Ding Tao <miyatsu@qq.com>
Whenever a Cortex-M0+ supports the VTOR register it makes no sense to
use the software vector relay mechanism. Therefore change the logic so
that SW_VECTOR_RELAY does not get enabled whenever a VTOR register is
present, but enable it if an M0+ has no VTOR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Test case should first check for next block in the coap packet and
unref the packet (assuming packet has been sent).
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Fixed a missing ticks unit to microsecond unit conversion
potentially caused incorrect window offsets being used while
establishing connections.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
ticker timespace reservation can range up to 10.24 seconds,
needing 19-bits to represent in 32KHz clock units. Hence,
fix controller implementation to use u32_t to store ticks
slot values.
Without this fix, the controller is asserting in scan_adv
sample when using continuous scanning with 2 second interval
and window.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactored the high frequency clock preparation advanced
feature to improve radio utilization during continuous
scanning.
The inter-event timespace value now considers the reserved
timespace while determining if the high frequency clock
will be retained. This reduces the preparation time, hence
increased radio use inside scan window.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor the invalid control PDU handling so as to reuse the
switch-case and hence, reduce code size and CPU time used.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In a scenario where a platform harbours multiple interrupts to the
extent the core cannot support it, an interrupt controller is added
as an additional level of interrupt. It typically combines several
sources of interrupt into one line that is then routed to the parent
controller.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Rather than having handler generate differently named log files,
generate the same for all handlers, so qemu, native and unit will now
generate handler.log.
This will simplify things and reporting will be consistent. Also, this
fixes a bug where we only included qemu.log in generated reports.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Intro page update to list the features and major changes that
happened in the last year
fixes#5136
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>