Invalid channel should be filtered in intmux isr, please refer to
page 1243~1244 of chapter 36 INTMUX of RV32M1 RM.
Note: Unlike the NVIC, the INTMUX does not latch pending source
interrupts. This means that the INTMUX output channel ISRs must
check for and handle a 0 value of the CHn_VEC register to account
for spurious interrupts.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
miv already had it defined, but let's shorten the names and use
them in the driver. This also adds it for sifive-freedom.
Signed-off-by: Olof Johansson <olof@lixom.net>
This is no longer needed, since all in-tree platforms are only using
the standard mstatus formats. Remove it to avoid the complexity.
Signed-off-by: Olof Johansson <olof@lixom.net>
The current GIC driver implementation only supports the GIC-400, which
implements the GICv2 interface.
This commit refactors the GIC driver to support multiple GIC versions
and adds GICv1 interface support (GICv1 and GICv2 interfaces are very
similar).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The current GIC configuration scheme is designed to support only one
specific type and version of GIC (i.e. GIC-400 that implements the
GICv2 interface).
This commit adds a set of GIC version configuration symbols that can
be selected by the SoC configuration to specify which version of GIC
interface is implemented in the SoC.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
sam0 and stm32 specific interrupt controller headers are meant to be
public, and as such should be found in
include/drivers/interrupt_controller and not in
drivers/interrupt_controllers.
Fixing documentation issues as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If it is such a thing (a CAVT intc), it will not be targeting Intel
s1000 SoC only. UP squarde ADSP use the same intc. So renaming it to
CAVS. Though CAVS name might be wrong (CAVS being an overall
architecture name, and not an IP block specification).
Reducing the amount of lines by using if/endif as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Pattern being <domain>_<model>.<c/h>.
Here interrupt_controller as a domain would be far too long so
shortening it to "intc", as DTS does actually.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The GIC-400 driver currently only supports SPIs because the (32) offset
for the INTIDs is hard-coded in the driver. At the driver level there is
no really difference between PPIs and SPIs so we can easily extend the
driver to support PPIs as well.
This is useful if we want to add support for the ARM Generic Timers that
use INTIDs in the PPI range.
SPI interrupts are in the range [0-987]. PPI interrupts are in the range
[0-15].
This commit adds interrupt 'type' cell to the GIC device tree binding
and changes the 'irq' cell to use interrupt type-specific index, rather
than a linear IRQ number.
The 'type'+'irq (index)' combo is automatically fixed up into a linear
IRQ number by the scripts/dts/gen_defines.py script.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add support for the built-in Programmable Interrupt Controller
found in the SweRV EH1 RISC-V CPU
Signed-off-by: Olof Kindgren <olof.kindgren@gmail.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Commit 5a9a33b0cf changes interrupt
destination in an attempt to broadcast interrupts. However, this
change causes interrupts to stop working on the UP Squared board
in non-SMP configuration. According to QEMU source code,
physical destination address 0xFF000000 is a special case where
it broadcasts the interrupts. However, none of the IOAPIC
documentation (that I can find) describes this behavior. So,
revert that commit.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Specific SW defined BLE LL parameters need to be set
if the user enables it on this platform. As such, conditionally
enable them directly into the defconfig.
INTMUX CH2 and CH3 are not available to be used if BT support
is enabled on Vega, because they are used internally by the
BLE SW LL
Signed-off-by: David Leach <david.leach@nxp.com>
Promote the private z_arch_* namespace, which specifies
the interface between the core kernel and the
architecture code, to a new top-level namespace named
arch_*.
This allows our documentation generation to create
online documentation for this set of interfaces,
and this set of interfaces is worth treating in a
more formal way anyway.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit switches from using device tree automatically
generated address-based defines to the instance id-based ones.
Without this change it is not be possible to re-use the driver
on boards where the timer and uart devices are located at different
locations than 0xe0002800 and 0xe0001800 respectively.
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
When SMP is enabled, the kernel expects that interrupts be delivered
to all CPUs in the system. Change the I/O APIC RTEs accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
In the general case, the local APIC can't be treated as a normal device
with a single boot-time initialization - on SMP systems, each CPU must
initialize its own. Hence the initialization proper is separated from
the device-driver initialization, and said initialization is called
from the early startup-assembly code when appropriate.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Like its 32-bit sibling, the 64-bit code should EOI inline rather than
invoking a function. Defeats the performance advantages of x2APIC.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Utilize the multi-level irq infrastructure and replace custom handling
for PLIC on riscv-privilege SoCs. The old code offset IRQs in drivers
and various places with RISCV_MAX_GENERIC_IRQ. Instead utilize Zephyr's
encoded IRQ and replace offsets in drivers with the IRQ define from DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* it's based on ARC SecureShield
* add basic secure service in arch/arc/core/secureshield
* necesssary changes in arch level
* thread switch
* irq/exception handling
* initialization
* add secure time support
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The GIC400 is a common interrupt controller that can be used with the
Cortex A and R series processors. This patch adds basic interrupt
handling for the GIC, but does not handle multiple routing or
priorities.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
With the upcoming riscv64 support, it is best to use "riscv" as the
subdirectory name and common symbols as riscv32 and riscv64 support
code is almost identical. Then later decide whether 32-bit or 64-bit
compilation is wanted.
Redirects for the web documentation are also included.
Then zephyrbot complained about this:
"
New files added that are not covered in CODEOWNERS:
dts/riscv/microsemi-miv.dtsi
dts/riscv/riscv32-fe310.dtsi
Please add one or more entries in the CODEOWNERS file to cover
those files
"
So I assigned them to those who created them. Feel free to readjust
as necessary.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Add a new sifive,plic-1.0.0 binding that inherits from the riscv,plic0
binding. The new binding adds a required riscv,ndev property, which
gives the number of external interrupts supported.
Use the new binding for microsemi-miv.dtsi (with a value of 31 for
riscv,ndev, from http://www.actel.com/ipdocs/MiV_RV32IMAF_L1_AHB_HB.pdf)
and riscv32-fe310.dtsi (which already assigns riscv,ndev).
Also remove a spurious riscv,ndev assignment from
riscv32-litex-vexriscv.dtsi.
Also make edtlib and the old scripts/dts/ scripts replace '.' in
compatible strings with '_' when generating identifiers.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The MVIC is no longer supported, and only the APIC-based interrupt
subsystem remains. Thus this layer of indirection is unnecessary.
This also corrects an oversight left over from the Jailhouse x2APIC
implementation affecting EOI delivery for direct ISRs only.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This file is 32-bit specific, so it is moved into the ia32/ directory
and references to it are updated accordingly.
Also, SP_ARG* definitions are no longer used, so they are removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move power.h to power/power.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move internal and architecture specific headers from include/drivers to
subfolder for interrupt_controller:
include/drivers/interrupt_controller/
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The Quark D2000 is the only x86 with an MVIC, and since support for
it has been dropped, the interrupt controller is orphaned. Removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
During conversion in #16815 a few device tree instance macro aliases
where missed (probably due to them existing to support future SoCs
and so not currently compiled), this fixes their usage.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Save few RAM bytes by declaring exti_irq_table as const.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Some code in stm32 exti driver was considering exti lines number
for which no IRQ_CONNECT was available. To be clear, this code
was not functional and since no one complained it was not used.
Besides, code to take into account these "high" irq lines was
complex hard to read and review.
Simplify state of things by removing completely this part of code.
It could be put back again piece by piece when required.
This change allows to get rid of EXTI_LINES definition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Function stm32_exti_enable is complex and makes it hard to extend
to new stm32 series.
When MP1 support was added, table exti_irq_table was introduced
to simplify stm32_exti_enable function.
This change extends usage of this table to other series, without
adding or removing any functionality.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When CONFIG_X2APIC is enabled, twiddle the appropriate MSR during
initialization to enable x2APIC mode.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
More clearly differentiate MVIC vs. APIC timer code, and use new APIC
accessors in include/drivers/loapic.h. Remove extraneous comments, and
other light cleanup work.
This driver is in need of a serious overhaul -- despite appearing to
have support for TICKLESS_KERNEL and DEVICE_POWER_MANAGEMENT, bitrot
has taken its toll and the driver will not build with these enabled.
These should be removed or made to work... but not in this patch.
Old x2APIC-related accessors in kernel_arch_func.h are eliminated.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Use new x2APIC-aware accessor functions in loapic.h instead of
locally-defined ones. Remove bitrot #defines (no longer used)
and extraneous comments with information from old data sheets.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Simple renaming and Kconfig reorganization. Choice of local APIC
access method isn't specific to the Jailhouse hypervisor.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
drivers/interrupt_controller/i8259.c is not a driver; it exists
solely to disable the i8259s when the configuration calls for it.
The six-byte sequence to mask the controllers is moved to crt0.S
and the pseudo-driver is removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The compiler and linker was generating errors after
disabling `CONFIG_EXTI_STM32` due to inconsistency
in `interrupt_controller/CMakeLists.txt`
and not considering this option in gpio implementation.
Signed-off-by: Maciej Zagrabski <maciej.zagrabski@grinn-global.com>
Add LiteX interrupt controller driver and bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Hygiene: We don't query MPtables (anymore?), so the related definitions
in the local APIC driver are unused. Removed.
Signed-off-by: Charles Youse <charles.youse@intel.com>
This adds interrupt support to the SAM0 GPIO driver. This is heavily
inspired by @nzmichaelh work in #5715. The primary difference
from that implementation is that here the External Interrupt
Controller (EIC) is separated out into an interrupt controller driver
that is less tightly coupled to the GPIO API. Instead it implements
more of a conversion from the EIC's own odd multiplexing to a more
traditional port and pin mask IRQ-like callback. Unfortunately,
through the EIC on the SAMD2x are relatively well behaved
in terms of pin to EIC line mappings, other chips that share the
peripheral interface are not. So the EIC driver implements a
per-line lookup to the pin and port pair using definitions extracted
from the ASF headers.
The EIC driver still makes some assumptions about how it will be used:
mostly it assumes exactly one callback per port. This should be fine
as the only intended user is the GPIO driver itself.
This has been tested with some simple programs and with
tests/drivers/gpio/gpio_basic_api on a SAMD21 breakout and an
adafruit_trinket_m0 board.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Use the RV32M1 SoC intmux driver initialization priority set by
Kconfig. Change the default to match the default value of 40 used
before.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The existing device_set_power_state() API works only in synchronous
mode and this is not desirable for devices(ex: Gyro) which take
longer time (few 100 mSec) to suspend/resume.
To support async mode, a new callback argument is added to the API.
The device drivers can asynchronously suspend/resume and call the
callback function upon completion of the async request.
This commit adds the missing callback parameter to all the drivers
to make it compliant with the new API.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Update reserved function names starting with one underscore, replacing
them as follows:
'_k_' with 'z_'
'_K_' with 'Z_'
'_handler_' with 'z_handl_'
'_Cstart' with 'z_cstart'
'_Swap' with 'z_swap'
This renaming is done on both global and those static function names
in kernel/include and include/. Other static function names in kernel/
are renamed by removing the leading underscore. Other function names
not starting with any prefix listed above are renamed starting with
a 'z_' or 'Z_' prefix.
Function names starting with two or three leading underscores are not
automatcally renamed since these names will collide with the variants
with two or three leading underscores.
Various generator scripts have also been updated as well as perf,
linker and usb files. These are
drivers/serial/uart_handlers.c
include/linker/kobject-text.ld
kernel/include/syscall_handler.h
scripts/gen_kobject_list.py
scripts/gen_syscall_header.py
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Converts the rv32m1 interrupt controller driver to use 'DT_' prefixed
defines instead of deprecated non-prefixed defines.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
RTC_Alarm IRQ is mentioned as an exti interrupt in documentation,
so it was available in exti handler.
Though, in Zephyr it is used driectly in RTC driver.
Having it in exti generates and issue when activating RTC driver,
so remove its handling from exti driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
IRQ lines definition in function __stm32_exti_connect_irqs ifdefery
does not match __stm32_exti_isr_x_y functions definitions.
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This allows the shared_irq driver to be configured by device tree.
With previous implementation, only the board configuration can
override the IRQ trigger, as the trigger config is a "choice" rather
than "config". With this patch, the driver can be fully configued at
the SoC level.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
exti driver implementation does not fit all SoCs because
some EXTI ip does not match stm32_exti register map provided.
Instead of providing exti register map for all SoCs, use LL API
which abstracts IP variations and enable uniform use of the drivers
on all STM32SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a level 2 interrupt controller for the RV32M1 SoC. This uses the
INTMUX peripheral.
As a first customer, convert the timer driver over to using this,
adding nodes for the LPTMR peripherals. This lets users select the
timer instance they want to use, and what intmux channel they want to
route its interrupt to, using DT overlays.
Signed-off-by: Marti Bolivar <marti@foundries.io>
Signed-off-by: Mike Scott <mike@foundries.io>
Some extensions to the multi-level interrupt controller are required
to support SoCs with more than four level 2 interrupt "aggregators".
Extend existing support to allow at most 8 level 2 or level 3
aggregators. Use Kconfig macro templates to cut down on boilerplate.
Try to clarify some aspects of the Kconfig help while we're at it, and
change the type of options which count things or are table offsets
from "hex" to "int", so that the generated .config is easier to read.
Finally, make some improvements to gen_isr_tables.py while we are
here. In particular, move some assignments around to cut down on
duplicated work, don't check for symbols we know must exist, and
improve the debug logging output's readability.
Signed-off-by: Marti Bolivar <marti@foundries.io>
Complete code factorization in stm32 exti drivers.
Add return value in case line is not implemented.
Except returned error code, refactor has been done iso-feature
compared to previous code. Hence error is reported only when
support was not available on previous series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Cleanup dependencies in Kconfig and convert some top-level options to
menuconfig. guard all dependent options with if instead of using
'depends on' for readibility.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Modified drivers to use DEVICE_AND_API_INIT() instead of DEVICE_INIT()
This will make sure driver_api,is populated at build time and is exposed
to user space
Signed-off-by: Varun Sharma <varun.sharma@intel.com>
GPIO pin interrupts share common EXTI resources.
Return an error when attempt to configure a line already in use.
Fixes#10611
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
