michaelh/zephyr
1
0
Fork 0
Code Releases Activity
42567 commits 87 branches 0 tags 617 MiB
Commit graph

5 commits

Author SHA1 Message Date
Kumar Gala a1b77fd589 zephyr: replace zephyr integer types with C99 types 
git grep -l 'u\(8\|16\|32\|64\)_t' | \
		xargs sed -i "s/u\(8\|16\|32\|64\)_t/uint\1_t/g"
	git grep -l 's\(8\|16\|32\|64\)_t' | \
		xargs sed -i "s/s\(8\|16\|32\|64\)_t/int\1_t/g"

Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
 2020-06-08 08:23:57 -05:00
Tomasz Bursztyka 97326c0445 device: Fix structure attributes access 
Since struct devconfig was merged earlier into struct device, let's fix
accessing config_info, name, ... attributes everywhere via:

grep -rlZ 'dev->config->' | xargs -0 sed -i 's/dev->config->/dev->/g'

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
 2020-05-08 23:07:44 +02:00
Gerson Fernando Budke d4f39742ea drivers: ieee802154: rf2xx: Add SRAM read method 
Add SRAM read method to enable advanced uses on at86rf2xx driver.

Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
 2020-03-09 14:17:06 +02:00
Piotr Mienkowski e1c10f6454 drivers: ieee802154_rf2xx: convert to the new GPIO API 
Use new GPIO configuration API, set pin active level in devicetree
source.

Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
 2020-02-05 12:00:36 +01:00
Gerson Fernando Budke 67289d07fe drivers: ieee802154: rf2xx: Add initial driver 
Add initial Atmel at86rf2xx transceiver driver. This driver uses device
tree to configure the physical interface. The driver had capability to
use multiple transceiver and systems with multiple bands can be used.
With this, 2.4GHz ISM and Sub-Giga can be used simultaneous.

Below a valid DT example. This samples assume same SPI port with two
transceivers.

&spi0 {
    status = "okay";
    label = "SPI_RF2XX";
    cs-gpios = <&porta 31 0 &porta 30 0>;

    rf2xx@0 {
        compatible = "atmel,rf2xx";
        reg = <0x0>;
        label = "RF2XX_0";
        spi-max-frequency = <7800000>;
        irq-gpios = <&portb 2 0>;
        reset-gpios = <&porta 3 0>;
        slptr-gpios = <&portb 3 0>;
        status = "okay";
    };

    rf2xx@1 {
        compatible = "atmel,rf2xx";
        reg = <0x1>;
        label = "RF2XX_1";
        spi-max-frequency = <7800000>;
        irq-gpios = <&portb 4 0>;
        reset-gpios = <&porta 4 0>;
        slptr-gpios = <&portb 4 0>;
        status = "okay";
    };
};

At the moment driver assume two transceiver are enouth for majority of
appications. Sub-Giga band will be enabled in future.

Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
 2019-12-13 11:23:23 +02:00