This is called when the USB host changes the virtual baud rate.
This is used by Arduino style boards to signal that the board should
reset into the bootloader.
Signed-off-by: Michael Hope <mlhx@google.com>
Allow feed operations that would stall due to internal peripheral
delays to complete immediately with -EAGAIN indicating that the feed
did not occur as expected.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The PCI API was originally limited to 32 bit addresses. Even though
it had code to skip over the high word in 64 bit BAR entries, it
refused to use it and returned a 32 bit value. Some devices in the
wild have default mappings from the firmware for devices above 4G.
Also remove the "iobar" API. It's dead code, we don't call it and we
don't test it. IO space BAR entries are a legacy feature from way,
way back in PCI history (I genuinely have never heard of a real device
that uses them!). And there's no difference in format between one of
these and a 32 bit "memory" BAR anyway, someone who actually had this
requirement could just use the existing API without worry.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Fix host RX thread being deadlocked. The deadlock occurs because the
RX thread is stuck waiting in conn_tx_alloc with K_FOREVER but if the
connection is disconnected only the RX thread can unblock it in the
handling of the disconnect event.
This commit fixes this deadlock by splitting the processing of the
disconnected event into two parts.
The part needed to unblock the RX is to release resources held by
unack'ed TX packets and mark the connection state as not connected
anymore.
The RX thread waiting for free_tx fifo and the TX thread waiting for
the bt_dev.le.pkts semaphore will both check the connected state after
having acquired them and will abort if disconnected.
The rest of the processing will be handled at normal RX thread
priority like normal.
Move the bt_recv_prio handling to the Bluetooth host when the host
has defined its own RX thread (CONFIG_BT_RECV_IS_RX_THREAD=n).
If the HCI driver has the RX thread (CONFIG_BT_RECV_IS_RX_THREAD=y),
then the responsibility to call bt_recv and bt_recv_prio correctly
falls to the HCI driver.
The helper function bt_hci_evt_is_prio() is replaced with
bt_hci_evt_get_flags() so that the HCI driver can do this correctly.
This decision to replace was made so that existing HCI drivers
maintained out-of-tree will fail at compile time with the new system.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bluetooth: host: Move bt_recv_prio to host when RX thread is defined
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add an additional option to the spi_cs_control struct that records how
the pin has been configured in devicetree. For drivers that are not
updated, the CS behaviour is the same as before (Push-Pull).
Use the devicetree knowledge with the GPIO subsystem so that the correct
physical pin levels for the CS pin are automatically selected.
Fixes#26267
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add api to raise SGI to target cores in affinity level identified
by MPIDR. Currently only EL1S is supported.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
This enables the ACPI_EC1 interface which is typically accessed
through ports 0x6A0 and 0x6A4 in Bios.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
With addition of flash_parameters structure, and supporting API call
to retrieve it, it is no longer needed to store write_block_size as
a part of flash_driver_api and it should be part of flash_parameters.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Adds flash_get_parameters call to API that returns pointer to structure
describing flash parameters.
Currently only erase_value parameter is provided via the structure.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
PCIe End Point can get three different reset interrupts from the
Root Complex, Function Level Reset (FLR), PCI Express Reset (PERST)
and Inband PCI Express Reset (INB PERST).
Add public API to let PCIe EP drivers register callback function
for each PCIe reset interrupt. This callback function should be
executed from corresponding reset interrupt handler if registered.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
This commit removes API functions and macros which were deprecated in
2.2 release. GPIO drivers are updated accordingly.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Updated rx_disable() description so that RX_RDY event is generated
after calling rx_disable. It contains data received prior to abort.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Introduce common API to achieve data transfer using memcpy
to/from outbound region of PCIe EP.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Add public APIs for PCIe endpoint driver:
- EP configuration space read/write
- Mapping/Unmapping of Host buffer and PCIe outbound region
- Raise interrupt to Host
These are minimal base APIs to make PCIe EP functional.
Also, add a Kconfig and an empty CMakeLists.txt for drivers to extend.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
1. expand PERIPHERAL_TO_PERIPHERAL
2. add slot size to 128 as i.MX-rt has 127 slot
3. add link_channel member in dma_conf which is used to
support chain channel
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
As written the specification when both period and pulse are zero is
inconsistent: allowed behavior would be to drive the pin at constant
active or constant inactive, depending on which condition was checked
first.
Clarify that driving constant active level requres a non-zero pulse
equal to period.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Clarify what happens when the period parameter is zero or equal
to the period.
Signed-off-by: Alexander Wachter <alexander.wachter@leica-geosystems.com>
Use device tree provided configurations for arm architecture timer
PPIs.
This fixes issue of timer ppi not working on most hardware where
edge-triggered PPI are not supported.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
The driver-specific config_info structure referenced from the device
structure is marked const. Some drivers fail to preserve that
qualifier when casting the pointer to the driver-specific structure,
violating MISRA 11.8.
Changes produced by scripts/coccinelle/const_config_info.cocci.
Some changes proposed by the script are not included because they
reveal mutation of state through the const pointer, though the
code works as long as the driver-specific object is defined without
the const qualifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
If IO APIC is in logical destination mode, local APICs compare their
logical APIC ID defined in LDR (Logical Destination Register) with
the destination code sent with the interrupt to determine whether or not
to accept the incoming interrupt.
This patch programs LDR in xAPIC mode to support IO APIC logical mode.
The local APIC ID from local APIC ID register can't be used as the
'logical APIC ID' because LAPIC ID may not be consecutive numbers hence
it makes it impossible for LDR to encode 8 IDs within 8 bits.
This patch chooses 0 for BSP, and for APs, cpu_number which is the index
to x86_cpuboot[], which ultimately assigned in z_smp_init[].
Signed-off-by: Zide Chen <zide.chen@intel.com>
Add API for recovering an I2C bus. This API can be used to recover
from situations where the I2C master and one or more I2C slaves are
out of synchronization (e.g. if the I2C master was reset in the middle
of an I2C transaction or if a noise pulse was induced on the SCL
line).
Fixes#23441.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds enumeration type for isochronous
endpoints specific information required by USB Audio Class.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
The DS3231 is an I2C real-time clock with internal temperature
compensated oscillator, maintaining civil time to 1 s precision with
nominal 2 ppm accuracy from 0-40 Cel.
The basic functionality is exposed as a counter that is always running
at 1 Hz. Much more functionality is exposed as driver-specific API,
including the ability to translate between the time scale of the DS3231
and the time scale of the Zephyr uptime clock. This allows correlation
of events in the system clock to UTC, TAI, or whatever time scale is
used to maintain the DS3231.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add an API to transmit a continuous wave at a fixed frequency. This
functionality is useful to test the radio in a lab setup.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Add basic driver for GIC V3 interrupt controller.
This implementation supports
- distributor, re-distributor and cpu interface initialization
- configuration and handling of SPI, PPI and SGI.
- V2 Legacy mode is not supported and uses system interface.
Current implementation supports GIC secure state only.
All interrupts are routed to Secure EL1 as 'irq' by configuring
them as Group1 Secure.
TODO:
- MPIDR based affinity routing setting.
- percpu redistributor probe
- message based SPI and SGI generation api
- EL1NS support. Legacy mode support.
- LPI/ITS is not supported.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Convert all canbus related API/samples/tests/subsys
to the new timeout API with k_timeout_t.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Get rid of legacy timeout API and move to new timeout API for LoRa.
This involves changes to API, SX1276 driver and sample application.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
API documentation for parameters that accept a duration specified in
milliseconds is updated to replace references to K_NO_WAIT with 0, and
K_FOREVER with SYS_FOREVER_MS.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DAC (digital to analog converter) peripheral driver with a generic API
suitable for most MCUs (only basic DAC features considered).
Signed-off-by: Martin Jäger <martin@libre.solar>
Several functions that are syscalls were passing structs by value
instead of by reference. Just changed that and implemented missing
verfication handlers for them.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
espi_read_flash should have implementation called
z_impl_espi_read_flash and not z_impl_espi_flash_read. Same thing for
espi_write_flash.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This commit adds more pin function definitions (PINMUX_FUNC_I through
PINMUX_FUNC_P) to the pinmux interface header.
The SAM D5x and E5x series devices, for instances, define up to the
"function N" and this change is necessary to support such devices.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Create support for muxed UARTs which are attached to a real
UART and which use GSM 07.10 muxing protocol to create virtual
channels that can be run on top of the real UART.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
HWINFO drivers should be responsible for ensuring that
the data structure is a sequence of bytes. That is not
what the current sam0 and nordic drivers do. The drivers
read the data as u32_t and then memcpy the data to a
buffer. This ensures the data has the endianness of the
underlying MCU, which in this case is Cortex M0 which
is little endian.
This commit fixes the endianness so the data can be
interpreted as a "left to right sequence of bytes".
This commit updates the API doc to provide clarification
of the data structure.
Add to 2.3 release notes.
Fixes#23444, #24103
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Michael Hope
