Fix flash operation timeout due to incorrect use of
secondary ticker to abort any radio in use. Ticker id 0
is reserved for split controller's pipeline preempt timeout.
Using the same ticker id caused the secondary ticker to
not be started if controller is using the same ticker id
for pipeline preempt timeout.
Fixes#26333.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
With addition of flash_parameters structure, and supporting API call
to retrieve it, it is no longer needed to store write_block_size as
a part of flash_driver_api and it should be part of flash_parameters.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
With addition of flash_get_parameters API call, it is needed to provide
support for the API to flash drivers.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver from DT_FLASH_BASE_ADDRESS and DT_FLASH_DEV_NAME to use
DT_REG_ADDR and DT_INST_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When enabled, instead of erasing entire flash page at once, page will
be erased in defined time slices. Erasing single page stalls CPU
for significant time share (~80ms) and partial erase divides the
operation in to the shorter time periods, resuming CPU operation in
meantime and enabling better scheduling of time sensitive operations.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Delay radio abort called in the flash driver to emulate the
behavior of pre-empt timeout in Bluetooth LL split
controller. Without this, the driver aborted radio events
in its reserved time space.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
There is timeout guard, in form of k_sem_get within work_in_time_slice,
used to detect if flash operation takes longer than expected maximum
and to return error code in such case. The processing of this timeout
is missing cancellation of scheduled ticker job that would attempt to
perform another operation. This causes problem as context for ticker
is created, on stack, within erase/write_in_timeslice which
would conclude when timeout occurs, folding the stack in process.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
According to NRF product specifications the smallest write unit is
32-bits. Added parameter 'CONFIG_EMULATE_ONE_BYTE_WRITE_ACCESS'
which allows one byte flash write using more complex operation.
Signed-off-by: Adam Kondraciuk <adam.kondraciuk@nordicsemi.no>
NRF devices hardware has flash protection which doesn't
reflect flash API definition well. So fare protection
mechanism was emulated by the software and the driver deals
with hardware flash protection on its own.
Recent change to protection behavior requirement allows
to remove flash API behavior emulation at all.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
So fare all nRF flash memories had flash base address at 0.
nRF flash driver was implemented in such way that it
really used absolute addresses, while convention are relative
addresses (for flash_map as well), which was not visible as start
address offset was 0.
It will become visible on nRF53 which has networking flash
with non-zero base address.
This patch switch nRF flash driver to use relative addresses for flash.
UICR absolute addressing is kept.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Modifications in 'is_regular_addr_valid()' function which didn't work
properly when flash base address was different than 0x00000000.
Added calculating address bounds with respect to flash base address.
Signed-off-by: Adam Kondraciuk <adam.kondraciuk@nordicsemi.no>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move flash.h to drivers/flash.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
nRF9160 can't provide FICR data while operation in non-secure
domain.
This patch start using flash layout properties provides by
nrfx API for get flash properties, which resolves problem
described above.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Introduce nrfx_nvmc driver into nordic flash driver implementation.
Thanks to that nrf9160 SoC becomes supported by the driver.
nrfx helps dealing with differences with interface to the NVMC
in secure and non-secure execution modes.
This patch adds NRFX_NVMC Kconfig entry for enabling nrfx_nvmc and
select it along with nordic flash driver.
Disabled UICR operation on nRF9160 for non-secure build
as UICR is not available in this mode.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Modified drivers to use DEVICE_AND_API_INIT() instead of DEVICE_INIT()
This will make sure driver_api,is populated at build time and is exposed
to user space
Signed-off-by: Varun Sharma <varun.sharma@intel.com>
Preparation to introduce the Upper Link Layer (ULL) and
Lower Link Layer (LLL) split architecture.
- Move SoC dependent HAL to vendor specific folder.
- Preparation to split data structures into ULL and LLL
types.
- Added more role and state conditional compilations.
- Added some work-in-progress implementation of advertising
extensions, will be used as inspiration in the new split
architecture work.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Nordic UICR are non-volatile memory registers for
configuring user-specific settings. Basically it is subset of flash
memory available in the SoC.
Add support for operations on NVM which belongs to UICR.
UICR are written or read as ordinary flash memory.
For erasing UICR it is required to call erase with UICR start
address and its size (this is caused by what hardware supported).
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use a lower slot duration than the used erase slot duration
to speed up the interval of write operations when in sync
with active Bluetooth connections.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When using CONFIG_MULTITHREADING=n, the semaphore primitives are
non-functional and useless. Remove their usage when this option is
enabled.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
2018-03-20 20:07:09 +01:00
Renamed from drivers/flash/soc_flash_nrf5.c (Browse further)
