Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use a default priority to avoid Kconfig blocking when priority
is not set in SoC or Board.
Change-Id: I4edda47b955a7ee834f04dc40d0decbd8dee6305
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
To many people, IPI connotes inter-processor interrupts on SMP
systems. Rename this to IPM, or Inter-Processor Mailboxes.
Change-Id: I032815e23c69a8297c0a43992132441c240fb71e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Use device name to find the UART device for uart_pipe usage,
instead of relying on an arbitrary index.
Change-Id: I36aaa4ed8f0b4905e4e741ca1464947e59f30869
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use device name to find the UART device for console usage, instead of
relying on an arbitrary index.
Change-Id: Iebe01c9bf392dfee6d8284367f67647f7d47561a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Move btshell.h out of samples into include/misc and rename to shell.h
Move btshell.c into driver/console and rename to console_handler_shell.c
as an shell implementation based on new config
CONFIG_CONSOLE_HANDLER_SHELL.
Add shell_register_app_cmd_handler for an to app to optionally call so
that it can receive cmdlines not handled by the cmds registered with
shell_init
Change-Id: I5c1585e62ff7a0ee923c6c92833cc762cf912bad
Signed-off-by: Thomas Heeley <thomas.heeley@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Put initialization priorities as device driver Kconfig
parameter.
Initialization priority value for each platform is defined
in the platform Kconfig file.
Drivers and platform code use SYS_DEFINE_DEVICE to add
and initialization function.
Change-Id: I2f4f3c7370dac02408a1b50a0a1bade8b427a282
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Original name was too generic and confusing. This patch renames
driver to pipe UART and moves it to console drivers folder. Kconfig
destription is also improved.
Change-Id: I716fdbf7d636bbdc03b0fce27a59fd866f473246
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Catch cases where index is set to negative or wrong values.
Change-Id: Ieab73e0fb12cecfc6c3c3d74c7d41f640bc88f01
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If console handler is defined uart console should also be defined.
Change-Id: I3efcc6c837f8f1621340f7f13bf0603d7dc42fb2
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Change all the Intel and Wind River code license from BSD-3 to Apache 2.
Change-Id: Id8be2c1c161a06ea8a0b9f38e17660e11dbb384b
Signed-off-by: Javier B Perez Hernandez <javier.b.perez.hernandez@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This introduces a generic driver set for console messages routed over
inter-processor interrupt (IPI) channels. These drivers bind to a
low-level IPI driver instance for the actual transport of messages.
ipi_console_sender installs printk and/or stdout hooks to forward
messages over IPI. There is currently no buffering on the sending side.
ipi_console_receiver installs an IPI callback which stashes incoming
characters into a ring buffer, which is monitored by a nanokernel
fiber. The fiber buffers the characters on a per-line basis and sends
them to either printk or stdout. Multiple instances of this driver
may be created in case you need to receive console data from multiple
CPUs.
Change-Id: Icebc110794fbe040f975101cd2ae6e78fb38645a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We are introducing other kinds of drivers which support a console
that isn't over a UART.
Change-Id: I0dddbdce958437b5709c5ab26252ed47d030413d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This buffer can be examined at runtime with a debugger to see what
is going on. Helpful if there are no other working console drivers
on the system.
Change-Id: I759467a57d16204b4b316c4f6fa8b7d5e1d1d236
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Move the baud rate selection for uart_console into Kconfig.
This allows apps to specify custom speed. Default is 115200
which should be supported by almost all RS232 and USB adapters
out in the past few years.
Change-Id: I78649bf2a1b2ddfc90a20d611a6454e3ad3b1b3a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This introduces the config option CONFIG_UART_CONSOLE,
and also CONFIG_CONSOLE. The UART console can finally
be disabled if desired.
The defconfigs are also being updated.
Change-Id: I5ebaf6471986deca105971e67fcddb43374de94a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use Kconfig to define this variable and remove its
previous definitions from board.h. This will simplify
creation of different variants from a single platform.
Change-Id: I0aaa5aa81dedf096c6d8c1ea2d509c71817336d3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit removes the UART_INTERRUPT_DRIVEN kconfig symbol from
the console section.
The symbols is already covered as a serial driver symbol and it
is a serial feature releated configuration option.
Change-Id: I4b9438d79eb7850b1293d5d963a75ce00733dbf7
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit standardize the Kconfig inclusion.
Selective sourcing of Kconfig files create conflict when merging
different configuration files (.config files).
Instead, now each kconfig symbols is dependant of its specific
DRV_* driver ksymbol.
Change-Id: I3d20d108a83f00d34067dc334758fd57e51feecf
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit add license headers to Kconfig files.
Change-Id: I79e60263b8c7b696463ecc84b8ad411af5415117
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
