Data toggle should be reset after SetConfiguration or
SetInterface request.
Always reset data toggle in usb_dc_ep_enable.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
USB Host expects dtoggle to be cleared after ClearFeature(Halt):
"[...] clearing the Halt feature via a ClearFeature(ENDPOINT_HALT)
request results in the endpoint no longer returning a STALL.
For endpoints using data toggle, regardless of whether an endpoint
has the Halt feature set, a ClearFeature(ENDPOINT_HALT) request always
results in the data toggle being reinitialized to DATA0."
- Subsection 9.4.5 of usb 2.0 spec (usb_20.pdf)
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Print the name of the discovered toolchain as well as the variable
used to initialize it.
This is nice to know when doing remote support, since users will
sometimes misconfigure their toolchain and not know what that means.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The header printed at the beginning of every west build is kind of
annoying. Let's remove it and just print the application source
directory at cmake time instead. The build directory and board are
already printed there, anyway, and that's all IDE users will see.
Let's clean up the BOARD to make it say "board" instead. That matches
the west build --board option name a bit more closely and is still
legible.
Likewise, let's not print any west build messages if we're just
incrementally recompiling. That's noisy.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add I2C and SPI bus communication routines in separate files,
and register one or the other as read/write callbacks based
on bus selection in DTS.
This commit is fixing issue #22348 as well, as the SPI part
is handling in the proper way the CS GPIO part.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
mtls_session_setup checks early if the given mode is valid and return
an error if not. CRYPTO_CIPHER_MODE_CTR is not a valid one so there is
no needed to have it in the switch.
CID: 20600
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The `irq_update` UART API function must always return 1 according to
the API documentations.
This commit fixes the `irq_update` API function to unconditionally
return `1`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The `irq_update` UART API function must always return 1 according to
the API documentations.
This commit fixes the `irq_update` API function to unconditionally
return '1'.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit fixes the multiple SERCOM interrupt handling for the SAM
D5x and E5x devices by replacing the obsolete device tree symbol with
the new `DT_INST` symbol.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32g0 SoC. Enable the independent watchdog
for the stm32g0 series for use with this driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Since driver is shared with other devices, it must be enabled
conditionally based on the number of instances. This avoid show
invalid options for devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
SAMV71 uses same driver of SAME70 and this enables the feature. Since
driver is shared with other devices, it must be enabled conditionally
based on the number of instances. This avoid show invalid options for
devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
When added SAM4E and SAMV71 platform the huge amount of refactor left
out this two configurations. This add missing configuration for all
supported devices.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The UART API now supports configure and configure_get functions,
however no tests were written for those functions. This
commit adds the framework and implementing tests for configure
and configure_get for UART API.
Fixes (#12872)
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
Instead of hardcoding the "zeth" network interface name, use the
name defined in Kconfig so that user can change it if needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Calculate length based on provided SSID string, so user does not have to
provide length explicitly over shell.
This patch also removes requirement of minimum 3 characters SSID, as
the shortest SSID can be even 1 character.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Older OT code used preprocessor #if conditionals, while newer code
used IS_ENABLED macro. Unify the approach by switching to the latter
option.
Additinally, fix inclusion issue that came out after switching to
IS_ENABLED.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add new transport handler for MQTT, with sendmsg-like functionality.
This allows TCP transport to send PUBLISH packets w/o fragmentation at
the TCP layer. Implement this new functionality for all existing
transports.
Fixes#22679
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
`mqtt_transport_write` failue was logged with `errno` value which is not
correct as the return value from the function is valid in this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This option specifies the name of the client.
See https://tools.ietf.org/html/rfc2132#section-3.14
This is useful for identification when looking in DHCP lease table.
Signed-off-by: Luuk Bosma <l.bosma@interay.com>
We now negotiate DNS servers in the IPCP configuration. This has been
observed to speed up the connection setup. The received DNS servers
are used by the DNS resolver library, but we leave it optional since
the static server list might be preferable.
Increase MAX_IPCP_OPTIONS to 4 so that we can nack all RFC 1877
options.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
It is not unusual that the peer does not provide an IP address in the
ipcp negotiation. But because ppp is a peer-to-peer protocol, we do
not actually need to know the peer's address to use the network.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
Move auto-negotiate sequence from driver initialization to link up event
Previously when booting without ethernet cable connected the
initialization would fail and never recover.
Now we can connect the ethernet cable any time and multiple times.
This also drastically reduces boot time to main.
Logging Link up and Link down events.
Logging speed and duplex from eth_gecko logger instead of eth_gecko_phy.
Signed-off-by: Luuk Bosma <l.bosma@interay.com>
TLS sockets did not increase refcount of a net_context running TCP,
which could lead to a crash upon TCP disconnection.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
pin is an unsigned variable so there is no meaning check if it is less
than zero.
CID :208407
CID :208408
CID :208410
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
daor-oti and wopu-ot also want to be added automatically as
reviewers to POSIX arch, native_posix, nrf52_bsim and bsim
related test apps.
(see CODEOWNERS for more info about which each is interested on)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When checking build directory against cache on windows, certain
corner cases can end up failing the comparison because of case
difference on an otherwise identical path. This can be avoided
by ignoring case on windows.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
Fix host resolving the peer identity address in enhanced connection
complete event when the resolving list in the controller is full and
resolution is done in the host.
Move the handling from legacy connection complete into enhanced
connection complete event so that it is done for both connection
complete events.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Implements several changes to the transport layer segmented tx to
improve group message performance:
- Moves retransmit counter to tx context instead of per packet. As every
unacked packet is sent every retransmit, the retransmit counters would
be the same in each segment. This makes it easier to control progress.
- Delays the scheduling of the retransmit until the completion of the
last segment by adding a seg_pending counter. This is essentially the
same as the old behavior, except that the old behavior might retrigger
the sending before all segments are finished if the advertising is
slow.
- Allows the group transmits to stop as soon as all retransmits have
been exhausted, instead of timing out waiting for acks that won't
come. This allows group tx to finish without error.
- Fixes a bug where a failed TX would block IV update.
- Cancels any pending transmissions of acked segments.
- Reduces log level for several common group tx scenarios that aren't
erronous.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
When available, the shell will use the CDB when configuring. This
replaces the default key for configuration and self-provisioning,
ensuring that there aren't multiple key values for the same indexes.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
* arc supports mpu gap filling now.
* these tests can be used for any arch which supports mpu gap
filling.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
when MPU_GAP_FILLING is configured, the default mpu entry
(kernel read + kernel write) will be used to fill the gaps
among mpu entires to avoid dynamic mpu region splitting.
This will bring better performance in thread switch but fewer
constraints on privileged codes.
when MPU_GAP_FILLING is not configured, a sw-based mpu dynamic
region splitting is used to bypass the limitation of no mpu region
overlap in hardware. This approach will consume more hardware
mpu entries and more time in thread switch.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
arc mpu ver3 does not allow mpu region overlap, so need to enable
MPU_REQUIRES_NON_OVERLAPPING_REGIONS.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
