The SPIM driver has been converted already. Convert the SPI and SPIS
drivers too. Leave existing Kconfigs in place.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Attempt to deinitialize an nrfx driver that is not initialized results
in an assertion failure reported by the driver. And such attempt could
happen in SPI shims when the power state was switched between states
other than ACTIVE.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update hal_nordic's revision, so that NRFX_ASSERT uses __ASSERT_NO_MSG
directly, not through the assert macro that comes from from libc,
as the definition of the latter might be different when some specific
libc version is used, and this could generate troubles.
Replace also uses of assert() with __ASSERT_NO_MSG() in nrfx driver
shims that use this macro without including the corresponding header
file (i.e. that implicitly rely on assert.h being included from
nrfx_glue.h, which is no longer the case).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
spi_context_lock() & spi_context_release() are called in transceive()
function for a better readability.
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
After switching to nrfx 2.0.0, the Kconfig choice options that allowed
enabling of pull-up or pull-down for MISO lines in SPIs and SPIMs are
not properly supported, they are simply ignored. This commit restores
the possibility of applying pull configuration for MISO lines.
In earlier nrfx versions, the MISO pull configuration could be only
set globally, in nrfx_config files, for all SPI and SPIM instances
together. Since nrfx 2.0.0, this configuration can be applied per
instance. This commit takes advantage of this possibility and instead
of using a common Kconfig option as a global setting for all instances,
allows applying individual instance settings via devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The defines should have had a _0 on them, now that we generate the
proper defines, fixup the cases that used that old scheme.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Introduced with the commit 7a9c4cbd9d,
by copy-pasting from "spi_nrfx_spim.c". Shame on me...
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Similar parts of code are aligned in the two shims, so that they
can be easily compared and updated if required.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The simple function that helps to integrate nrfx IRQ handlers with
the IRQ_CONNECT macro can be used in shims for various nrfx drivers,
not only the SPI one.
Similarly, the macro for getting the IRQ number from the peripheral
base address needs to be widely available. It should be even moved
to <nrfx_common.h> in some next nrfx update.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This adds a translation layer to make the nrfx driver for the legacy
(i.e. without EasyDMA) nRF SPI peripheral accessible via the updated
Zephyr's API of the SPI driver.
Configuration files are already prepared for adding support for SPIM
(Master with EasyDMA) and SPIS (Slave with EasyDMA) peripherals.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
