The OPENSDA_FW and LPCLINK_FW cmake variables are remnants of pre-west
days where we used an environment variable to set the desired debug host
tool, such as jlink or pyocd, based on which debug probe firmware was
loaded on the board. We now have two possible ways to do this, neither
of which requires the nxp-specific OPENSDA_FW or LPCLINK_FW variables:
1. Set standardized cmake runner variables when generating the build
system:
$ west build -- -DBOARD_FLASH_RUNNER=jlink -DBOARD_DEBUG_RUNNER=jlink
2. Use the west "--runner" argument with the debug and flash commands:
$ west debug -r jlink
Remove the now unnecessary OPENSDA_FW ond LPCLINK_FW variables and
update board documentation accordingly.
A few boards (frdm_kw41z, hexiwear_k64, mimxrt10{20,50,60,64}_evk)
reordered pyocd.board.cmake and jlink.board.cmake includes to preserve
the default runner when OPENSDA_FW was not explicitly set.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Once the TPM driver and the required configs have been added,
now this patch enables the usage of the PWM framework on KW41Z
SoCs. As such, the DTS gets the proper nodes and the pinmuxing
is done according to the configuration requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Instead of having a mix of west and CMake/ninja instructions for
building and flashing, document it using only west. This will help
clarify that west is the default build tool in Zephyr and should also
reduce confusion over what tool to use.
Note that the biggest change is changing the default in
doc/extensions/zephyr/application.py for :tool:, from all to west.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Clean up some stray references to cmake in doc, boards and
samples that don't make explicit use of the zephyr app extension,
as well as other minor doc fixes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Reworks the programming and debugging section in the freedom board
documents to leverage the new debugging guide covering debug probes and
host tools.
These boards support OpenSDA DAPLink and OpenSDA J-Link onboard debug
probes. They can also support an external J-Link probe, but this
requires board modifications (cutting traces) and is therefore not
documented.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fixes broken user guide and schematics links in nxp board documentation.
Updates remaining nxp.com links from http to https.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the frdm_kw41z board to mux spi signals on pins PTC16-19.
Updates the board document to reflect that spi is supported on these
pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable one adc channel on the SoC's PTB2 pin,
which is routed to the Arduino header A2 pin. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that NXP boards support 'make flash' and 'make debug' via pyOCD and
Segger J-Link, update all the NXP board docs accordingly. Adds a new
generalized OpenSDA document so certain details don't have to be
repeated for every OpenSDA board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Adds initial support and documentation for the frdm_kw41z board.
- Configures the kw41 to use the 32 MHz external oscillator on the board
to generate a 40 MHz system clock. The clock settings match the MCUX
SDK hello_world example project.
- Provides pinmux settings for the uart, i2c, LEDs, and switches
- Enables pinmux, gpio, uart, and i2c driver instances
- Configures the fxos8700 accelerometer/magnetometer driver
Jira: ZEP-1390
Change-Id: I025a0eae3d380eaf90b02683acf5c592e2204a2e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
