Remove configuration parameter CONFIG_BUS_TYPE. Now we may
make use of DT_ST_LSM6DSL_BUS_I2C and DT_ST_LSM6DSL_BUS_SPI
definition to select the bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
As explained in issue #8915 the STM32F4xx SoC family I2C
does not work well in Standard mode (100KHz). So let's
configure i2c3 in Fast mode (400KHz).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit is taking care of following stuff:
1. pinmux: STM32F4 micro is using I2S5_CK and I2S_SD to interface with
on-board microphone.
2. default configuration:
- enable I2S5 and configure PLLI2S properly to generate
I2SxCLK = 128MHz.
- enable DMA
Note:
As stated in issue #9028 we needed to take care of a known SPI/I2S bug
implementing the following two actions:
A. APB2 clock has been slowed down to 42MHz.
B. The SPI/I2S clock gpio speed has been set to very_high_speed.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Add i2c/spi/gpio to the supported list to enable the CI to correctly
run the 96b_argonkey board sample.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The device name was missing for the lsm6dsl sensor in the 96b_argonkey
dts fixup, causing build warnings in tests/drivers/build_all.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch is equivalent to 7b0ce85242,
but applied to more boards. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Argonkey board building has been recently broken by a LSM6DSL sensor
driver fix (see commit: a013ce3bf0).
The board configuration file must now enable HAS_DTS_GPIO_DEVICE macro
instead of HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for button nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The old GCC ARM Embedded website on launchpad
(https://launchpad.net/gcc-arm-embedded) has been superseeded by the new
GNU Arm Embedded one
(https://developer.arm.com/open-source/gnu-toolchain/gnu-rm).
This also means a change of name from "GCC" to "GNU". Reflect this in
the enviroment variables so that the proper term is used henceforth.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The ArgonKey board has 12 leds controlled by TI LP3943 led
controller. Add the support in the BSP.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Both variables were used (with the same value) interchangeably
throughout CMake files and per the discussion in GH issue,
ZEPHYR_BASE is preferred.
Also add a comment with explanation of one vs. the other.
Tested by building hello_world for several boards ensuring no errors.
Fixes#7173.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
The choice symbol LSM6DSL_EXT0_LIS2MDL was given a 'default' in
Kboards/arm/96b_argonkey/Kconfig.defconfig, but 'default' has no effect
on choice symbols, triggering a warning from Kconfiglib.
Instead of adding a default to the choice symbol, change the default of
the 'choice' itself by giving it name and adding the default in
Kconfig.defconfig.
This requires that we remove the default on the "base" definition of the
'choice', due to some messiness related to the Zephyr-specific
prefer-later-defaults behavior (see the 'Zephyr-specific Kconfig
behavior for defaults' section in the Board Porting Guide). Choices were
overlooked when that patch was added to the C tools, meaning choices
still prefer earlier defaults. The crux is that Kconfig.defconfig files
are included last.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the named choices feature introduced by PR #6966
and configure LSM6DSL on ArgonKey board.
The two named choices introduced in LSM6DSL are:
- LSM6DSL_BUS_TYPE (default LSM6DSL_I2C)
- LSM6DSL_TRIGGER_MODE (default LSM6DSL_TRIGGER_NONE)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds dts support to lps22hb/hts221/vl53l0x
I2C sensors as well as lsm6dsl SPI sensor.
Since some info, like gpio for irq triggering or SPI bus
characteristics, may be provided through dts, they need
to be made optional in the LSM6DSL driver by usage of
macros like HAS_DTS_SPI_PINS or HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Describe in documentation few methods that can be used by
users to flash the ArgonKey with a binary image.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
ArgonKey board is a 96boards sensor hub platform for all 96Boards
compliant family products. The ArgonKey packs a Cortex-M4 chip
together with a set of motion, environmental and ambiental sensors
and can be used as a development platform for many different
applications.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
