diff --git a/subsys/bluetooth/controller/Kconfig.ll_sw_split b/subsys/bluetooth/controller/Kconfig.ll_sw_split
index d86c4655d93..64a3f323ca9 100644
--- a/subsys/bluetooth/controller/Kconfig.ll_sw_split
+++ b/subsys/bluetooth/controller/Kconfig.ll_sw_split
@@ -682,115 +682,6 @@ config BT_CTLR_USER_CPR_INTERVAL_MIN
 
 endmenu
 
-comment "BLE Controller hardware configuration"
-
-menuconfig BT_CTLR_GPIO_PA
-	bool "Power Amplifier GPIO interface"
-	depends on !SOC_SERIES_NRF51X
-	help
-	  Enable GPIO interface to a Power Amplifier. This allows hardware
-	  designs using PA to let the Controller toggle their state based on
-	  radio activity.
-
-if BT_CTLR_GPIO_PA
-
-config BT_CTLR_GPIO_PA_PIN
-	int "Power Amplifier GPIO pin number"
-	range 0 47 if SOC_NRF52840 || SOC_NRF5340_CPUNET
-	range 0 31
-	help
-	  GPIO Pin number connected to a Power Amplifier.
-
-config BT_CTLR_GPIO_PA_POL_INV
-	bool "Inverted polarity for the PA pin"
-	help
-	  Enable inverted polarity (active low) for the PA pin.
-
-config BT_CTLR_GPIO_PA_OFFSET
-	int "Time from PA ON to Tx ready"
-	default 5
-	range 0 15
-	help
-	  Time before Tx ready to turn on PA in micro seconds.
-
-endif # BT_CTLR_GPIO_PA
-
-menuconfig BT_CTLR_GPIO_LNA
-	bool "Low Noise Amplifier GPIO interface"
-	depends on !SOC_SERIES_NRF51X
-	help
-	  Enable GPIO interface to a Low Noise Amplifier. This allows hardware
-	  designs using LNAs to let the Controller toggle their state based on
-	  radio activity.
-
-if BT_CTLR_GPIO_LNA
-
-config BT_CTLR_GPIO_LNA_PIN
-	int "Low Noise Amplifier GPIO pin number"
-	range 0 47 if SOC_NRF52840 || SOC_NRF5340_CPUNET
-	range 0 31
-	help
-	  GPIO Pin number connected to a Low Noise Amplifier.
-
-config BT_CTLR_GPIO_LNA_POL_INV
-	bool "Inverted polarity for the LNA pin"
-	help
-	  Enable inverted polarity (active low) for the LNA pin.
-
-config BT_CTLR_GPIO_LNA_OFFSET
-	int "Time from LNA ON to Rx ready"
-	default 5
-	range 0 15
-	help
-	  Time before Rx ready to turn on LNA in micro seconds.
-
-endif # BT_CTLR_GPIO_LNA
-
-menuconfig BT_CTLR_FEM_NRF21540
-	bool "nRF21540 GPIO interface"
-	depends on !SOC_SERIES_NRF51X
-	select BT_CTLR_GPIO_PA
-	select BT_CTLR_GPIO_LNA
-	help
-	  Enable PDN and CSN GPIO interface for the nRF21540. This allows
-	  hardware designs using the nRF21540 to let the controller toggle
-	  their state based on radio activity.
-
-if BT_CTLR_FEM_NRF21540
-
-config BT_CTLR_GPIO_PDN_PIN
-	int "FEM PDN pin number"
-	range 0 47 if SOC_NRF52840 || SOC_NRF5340_CPUNET
-	range 0 31
-	help
-	  GPIO Pin number connected to the PDN pin of the nRF21540 FEM.
-
-config BT_CTLR_GPIO_PDN_POL_INV
-	bool "Inverted polarity for the PDN pin"
-	help
-	  Enable inverted polarity (active low) for the PDN pin.
-
-config BT_CTLR_GPIO_CSN_PIN
-	int "FEM CSN pin number"
-	range 0 47 if SOC_NRF52840 || SOC_NRF5340_CPUNET
-	range 0 31
-	help
-	  GPIO Pin number connected to the CSN pin of the nRF21540 FEM.
-
-config BT_CTLR_GPIO_CSN_POL_INV
-	bool "Inverted polarity for the CSN pin"
-	default y
-	help
-	  Enable inverted polarity (active low) for the CSN pin.
-
-config BT_CTLR_GPIO_PDN_CSN_OFFSET
-	int "Time from PDN and CSN toggle to PA/LNA pin toggle"
-	range 0 20
-	help
-	  Time from PDN and CSN toggle to PA/LNA pin toggle in micro seconds.
-
-endif # BT_CTLR_FEM_NRF21540
-
 comment "BLE Controller debug configuration"
 
 config BT_CTLR_PROFILE_ISR