boards: arm: Add board definition for Adafruit Feather nRF52840 Express

Add support for adafruit_feather_nrf52840 board.

Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>

boards/arm/adafruit_feather_nrf52840/Kconfig

@@ -0,0 +1,10 @@
+# Adafruit Feather nRF52840 Express board configuration
+
+# Copyright (c) 2020 Tobias Svehagen
+# SPDX-License-Identifier: Apache-2.0
+
+config BOARD_ENABLE_DCDC
+	bool "Enable DCDC mode"
+	select SOC_DCDC_NRF52X
+	default y
+	depends on BOARD_ADAFRUIT_FEATHER_NRF52840

boards/arm/adafruit_feather_nrf52840/Kconfig.board

@@ -0,0 +1,8 @@
+# Adafruit Feather nRF52840 Express board configuration
+
+# Copyright (c) 2020 Tobias Svehagen
+# SPDX-License-Identifier: Apache-2.0
+
+config BOARD_ADAFRUIT_FEATHER_NRF52840
+	bool "Adafruit Feather nRF52840 Express"
+	depends on SOC_NRF52840_QIAA

boards/arm/adafruit_feather_nrf52840/Kconfig.defconfig

@@ -0,0 +1,40 @@
+# Adafruit Feather nRF52840 Express board configuration
+
+# Copyright (c) 2020 Tobias Svehagen
+# SPDX-License-Identifier: Apache-2.0
+
+if BOARD_ADAFRUIT_FEATHER_NRF52840
+
+config BOARD
+	default "adafruit_feather_nrf52840"
+
+config ADC_0
+	default y
+	depends on ADC
+
+config I2C_0
+	default y
+	depends on I2C
+
+config SPI_1
+	default y
+	depends on SPI
+
+if USB
+
+config USB_NRFX
+	default y
+
+config USB_DEVICE_STACK
+	default y
+
+endif # USB
+
+config IEEE802154_NRF5
+	default y
+	depends on IEEE802154
+
+config BT_CTLR
+	default BT
+
+endif # BOARD_ADAFRUIT_FEATHER_NRF52840

boards/arm/adafruit_feather_nrf52840/adafruit_feather_nrf52840.dts

@@ -0,0 +1,133 @@
+/*
+ * Copyright (c) 2020 Tobias Svehagen
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/dts-v1/;
+#include <nordic/nrf52840_qiaa.dtsi>
+
+/ {
+	model = "Adafruit Feather nRF52840 Express";
+	compatible = "nordic,nrf52840-qiaa", "nordic,nrf52840";
+
+	chosen {
+		zephyr,console = &uart0;
+		zephyr,shell-uart = &uart0;
+		zephyr,uart-mcumgr = &uart0;
+		zephyr,bt-mon-uart = &uart0;
+		zephyr,bt-c2h-uart = &uart0;
+		zephyr,sram = &sram0;
+		zephyr,flash = &flash0;
+		zephyr,code-partition = &slot0_partition;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led0: led_0 {
+			gpios = <&gpio1 15 0>;
+			label = "Red LED";
+		};
+		led1: led_1 {
+			gpios = <&gpio1 10 0>;
+			label = "Blue LED";
+		};
+	};
+
+	buttons {
+		compatible = "gpio-keys";
+		button0: button_0 {
+			gpios = <&gpio1 2 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
+			label = "Push button switch";
+		};
+	};
+
+	/* These aliases are provided for compatibility with samples */
+	aliases {
+		led0 = &led0;
+		led1 = &led1;
+		sw0 = &button0;
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+&gpiote {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&uart0 {
+	compatible = "nordic,nrf-uart";
+	current-speed = <115200>;
+	status = "okay";
+	tx-pin = <25>;
+	rx-pin = <24>;
+};
+
+&i2c0 {
+	status = "okay";
+	sda-pin = <12>;
+	scl-pin = <11>;
+};
+
+&spi1 {
+	status = "okay";
+	sck-pin = <14>;
+	mosi-pin = <13>;
+	miso-pin = <15>;
+};
+
+&flash0 {
+	/*
+	 * For more information, see:
+	 * http://docs.zephyrproject.org/latest/guides/dts/index.html#flash-partitions
+	 */
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		boot_partition: partition@0 {
+			label = "mcuboot";
+			reg = <0x000000000 0x0000C000>;
+		};
+		slot0_partition: partition@c000 {
+			label = "image-0";
+			reg = <0x0000C000 0x000067000>;
+		};
+		slot1_partition: partition@73000 {
+			label = "image-1";
+			reg = <0x00073000 0x000067000>;
+		};
+		scratch_partition: partition@da000 {
+			label = "image-scratch";
+			reg = <0x000da000 0x0001e000>;
+		};
+
+		/*
+		 * The flash starting at 0x000f8000 and ending at
+		 * 0x000fffff is reserved for use by the application.
+		 */
+
+		/* Storage partition will be used by FCB/NFFS/NVS if enabled. */
+		storage_partition: partition@f8000 {
+			label = "storage";
+			reg = <0x000f8000 0x00008000>;
+		};
+	};
+};
+
+&usbd {
+	compatible = "nordic,nrf-usbd";
+	status = "okay";
+};

boards/arm/adafruit_feather_nrf52840/adafruit_feather_nrf52840.yaml

@@ -0,0 +1,16 @@
+identifier: adafruit_feather_nrf52840
+name: Adafruit Feather nRF52840 Express
+type: mcu
+arch: arm
+toolchain:
+  - zephyr
+  - gnuarmemb
+  - xtools
+supported:
+  - adc
+  - usb_device
+  - usb_cdc
+  - ble
+  - ieee802154
+  - watchdog
+  - counter

boards/arm/adafruit_feather_nrf52840/adafruit_feather_nrf52840_defconfig

@@ -0,0 +1,22 @@
+# SPDX-License-Identifier: Apache-2.0
+
+CONFIG_SOC_SERIES_NRF52X=y
+CONFIG_SOC_NRF52840_QIAA=y
+CONFIG_BOARD_ADAFRUIT_FEATHER_NRF52840=y
+
+# Enable MPU
+CONFIG_ARM_MPU=y
+
+# enable GPIO
+CONFIG_GPIO=y
+
+# enable uart driver
+CONFIG_SERIAL=y
+CONFIG_UART_0_NRF_UART=y
+
+# enable console
+CONFIG_CONSOLE=y
+CONFIG_UART_CONSOLE=y
+
+# additional board options
+CONFIG_GPIO_AS_PINRESET=y

boards/arm/adafruit_feather_nrf52840/board.cmake

@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: Apache-2.0
+
+board_runner_args(jlink "--device=nrf52" "--speed=4000")
+board_runner_args(pyocd "--target=nrf52" "--frequency=4000000")
+board_runner_args(blackmagicprobe "--gdb-serial=/dev/ttyBmpGdb")
+include(${ZEPHYR_BASE}/boards/common/jlink.board.cmake)
+include(${ZEPHYR_BASE}/boards/common/pyocd.board.cmake)
+include(${ZEPHYR_BASE}/boards/common/blackmagicprobe.board.cmake)

boards/arm/adafruit_feather_nrf52840/doc/index.rst

@@ -0,0 +1,147 @@
+.. _adafruit_feather_nrf52840:
+
+Adafruit Feather nRF52840 Express
+#################################
+
+Overview
+********
+
+The Adafruit Feather nRF52840 provides support for the Nordic Semiconductor
+nRF52840 ARM Cortex-M4F CPU and the following devices:
+
+* :abbr:`ADC (Analog to Digital Converter)`
+* CLOCK
+* FLASH
+* :abbr:`GPIO (General Purpose Input Output)`
+* :abbr:`I2C (Inter-Integrated Circuit)`
+* :abbr:`MPU (Memory Protection Unit)`
+* :abbr:`NVIC (Nested Vectored Interrupt Controller)`
+* :abbr:`PWM (Pulse Width Modulation)`
+* RADIO (Bluetooth Low Energy and 802.15.4)
+* :abbr:`RTC (nRF RTC System Clock)`
+* Segger RTT (RTT Console)
+* :abbr:`SPI (Serial Peripheral Interface)`
+* :abbr:`UART (Universal asynchronous receiver-transmitter)`
+* :abbr:`USB (Universal Serial Bus)`
+* :abbr:`WDT (Watchdog Timer)`
+
+.. figure:: img/adafruit_feather_nrf52840.jpg
+     :width: 640px
+     :align: center
+     :alt: Adafruit Feather nRF52840 Express
+
+Hardware
+********
+
+- nRF52840 ARM Cortex-M4F processor at 64 MHz
+- 1 MB flash memory and 256 KB of SRAM
+- Battery connector and charger for 3.7 V lithium polymer batteries
+- Charging indicator LED
+- 2 User LEDs
+- 1 NeoPixel LED
+- Reset button
+- SWD connector
+
+Supported Features
+==================
+
+The Adafruit Feather nRF52840 board configuration supports the
+following hardware features:
+
++-----------+------------+----------------------+
+| Interface | Controller | Driver/Component     |
++===========+============+======================+
+| ADC       | on-chip    | adc                  |
++-----------+------------+----------------------+
+| CLOCK     | on-chip    | clock_control        |
++-----------+------------+----------------------+
+| FLASH     | on-chip    | flash                |
++-----------+------------+----------------------+
+| GPIO      | on-chip    | gpio                 |
++-----------+------------+----------------------+
+| I2C       | on-chip    | i2c                  |
++-----------+------------+----------------------+
+| MPU       | on-chip    | arch/arm             |
++-----------+------------+----------------------+
+| NVIC      | on-chip    | arch/arm             |
++-----------+------------+----------------------+
+| PWM       | on-chip    | pwm                  |
++-----------+------------+----------------------+
+| RADIO     | on-chip    | Bluetooth,           |
+|           |            | ieee802154           |
++-----------+------------+----------------------+
+| RTC       | on-chip    | system clock         |
++-----------+------------+----------------------+
+| SPI       | on-chip    | spi                  |
++-----------+------------+----------------------+
+| UART      | on-chip    | serial               |
++-----------+------------+----------------------+
+| USB       | on-chip    | usb                  |
++-----------+------------+----------------------+
+| WDT       | on-chip    | watchdog             |
++-----------+------------+----------------------+
+
+Other hardware features are not supported by the Zephyr kernel.
+
+Connections and IOs
+===================
+
+The `Adafruit Feather nRF52840 Express Learn site`_ has detailed
+information about the board including `pinouts`_ and the `schematic`_.
+
+LED
+---
+
+* LED0 (red) = P1.15
+* LED1 (blue) = P1.10
+
+Push buttons
+------------
+
+* SWITCH = P1.02
+* RESET = P0.18
+
+Programming and Debugging
+*************************
+
+Applications for the ``adafruit_feather_nrf52840`` board configuration
+can be built and flashed in the usual way (see :ref:`build_an_application`
+and :ref:`application_run` for more details).
+
+Flashing
+========
+
+Flashing Zephyr onto the ``adafruit_feather_nrf52480`` board requires
+an external programmer. The programmer is attached to the SWD header.
+
+Build the Zephyr kernel and the :ref:`blinky-sample` sample application.
+
+   .. zephyr-app-commands::
+      :zephyr-app: samples/blinky
+      :board: adafruit_feather_nrf52840
+      :goals: build
+      :compact:
+
+Flash the image.
+
+   .. zephyr-app-commands::
+      :zephyr-app: samples/blinky
+      :board: adafruit_feather_nrf52840
+      :goals: flash
+      :compact:
+
+You should see the the red LED blink.
+
+References
+**********
+
+.. target-notes::
+
+.. _Adafruit Feather nRF52840 Express Learn site:
+    https://learn.adafruit.com/introducing-the-adafruit-nrf52840-feather/
+
+.. _pinouts:
+    https://learn.adafruit.com/introducing-the-adafruit-nrf52840-feather/pinouts
+
+.. _schematic:
+    https://learn.adafruit.com/introducing-the-adafruit-nrf52840-feather/downloads

tests/drivers/adc/adc_api/src/test_adc.c

@@ -31,13 +31,14 @@
 #define ADC_2ND_CHANNEL_INPUT	NRF_ADC_CONFIG_INPUT_3
 
 #elif defined(CONFIG_BOARD_NRF52_PCA10040) || \
-      defined(CONFIG_BOARD_NRF52840_PCA10056) || \
-      defined(CONFIG_BOARD_NRF52840_BLIP) || \
-      defined(CONFIG_BOARD_NRF52840_PAPYR) || \
-      defined(CONFIG_BOARD_NRF52833_PCA10100) || \
-      defined(CONFIG_BOARD_BL652_DVK) || \
-      defined(CONFIG_BOARD_BL654_DVK) || \
-      defined(CONFIG_BOARD_DEGU_EVK)
+	defined(CONFIG_BOARD_NRF52840_PCA10056) || \
+	defined(CONFIG_BOARD_NRF52840_BLIP) || \
+	defined(CONFIG_BOARD_NRF52840_PAPYR) || \
+	defined(CONFIG_BOARD_NRF52833_PCA10100) || \
+	defined(CONFIG_BOARD_BL652_DVK) || \
+	defined(CONFIG_BOARD_BL654_DVK) || \
+	defined(CONFIG_BOARD_DEGU_EVK) || \
+	defined(CONFIG_BOARD_ADAFRUIT_FEATHER_NRF52840)
 
 #include <hal/nrf_saadc.h>
 #define ADC_DEVICE_NAME		DT_ADC_0_NAME