sys_log: replace old debug macros at pcal9535a driver

pcal9535a driver is now using new system log macros and updated the
Kconfig variable to be a level rather than a bool.

JIRA: ZEP-311

Change-Id: Ic3d6c72630e66ac116c1e8954c32254677c51566
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
This commit is contained in:
Genaro Saucedo Tejada 2016-07-26 17:55:33 -05:00 committed by Andrew Boie
commit 93b9196ab9
2 changed files with 35 additions and 30 deletions

View file

@ -26,12 +26,25 @@ menuconfig GPIO_PCAL9535A
if GPIO_PCAL9535A
config GPIO_PCAL9535A_DEBUG
bool "Enable PCAL9535A Debugging"
config SYS_LOG_GPIO_PCAL9535A_LEVEL
int
prompt "PCAL9535A driver log level"
depends on GPIO_PCAL9535A
default n
default 0
help
Enable debugging for PCAL9535A driver.
Sets log level for clock PCAL9535A driver
Levels are:
- 0 OFF, do not write
- 1 ERROR, only write SYS_LOG_ERR
- 2 WARNING, write SYS_LOG_WRN in adition to previous level
- 3 INFO, write SYS_LOG_INF in adition to previous levels
- 4 DEBUG, write SYS_LOG_DBG in adition to previous levels
config GPIO_PCAL9535A_INIT_PRIORITY
int

View file

@ -28,17 +28,8 @@
#include "gpio_pcal9535a.h"
#ifndef CONFIG_GPIO_PCAL9535A_DEBUG
#define DBG(...) { ; }
#else
#if defined(CONFIG_STDOUT_CONSOLE)
#include <stdio.h>
#define DBG printf
#else
#include <misc/printk.h>
#define DBG printk
#endif /* CONFIG_STDOUT_CONSOLE */
#endif /* CONFIG_GPIO_PCAL9535A_DEBUG */
#define SYS_LOG_LEVEL CONFIG_SYS_LOG_GPIO_PCAL9535A_LEVEL
#include <misc/sys_log.h>
/* Register definitions */
#define REG_INPUT_PORT0 0x00
@ -107,13 +98,13 @@ static int _read_port_regs(struct device *dev, uint8_t reg,
ret = i2c_burst_read(i2c_master, i2c_addr, reg, buf->byte, 2);
if (ret) {
DBG("PCAL9535A[0x%X]: error reading register 0x%X (%d)\n",
i2c_addr, reg, ret);
SYS_LOG_ERR("PCAL9535A[0x%X]: error reading register 0x%X (%d)",
i2c_addr, reg, ret);
goto error;
}
DBG("PCAL9535A[0x%X]: Read: REG[0x%X] = 0x%X, REG[0x%X] = 0x%X\n",
i2c_addr, reg, buf->byte[0], (reg + 1), buf->byte[1]);
SYS_LOG_DBG("PCAL9535A[0x%X]: Read: REG[0x%X] = 0x%X, REG[0x%X] = 0x%X",
i2c_addr, reg, buf->byte[0], (reg + 1), buf->byte[1]);
error:
return ret;
@ -141,13 +132,14 @@ static int _write_port_regs(struct device *dev, uint8_t reg,
uint16_t i2c_addr = config->i2c_slave_addr;
int ret;
DBG("PCAL9535A[0x%X]: Write: REG[0x%X] = 0x%X, REG[0x%X] = 0x%X\n",
i2c_addr, reg, buf->byte[0], (reg + 1), buf->byte[1]);
SYS_LOG_DBG("PCAL9535A[0x%X]: Write: REG[0x%X] = 0x%X, REG[0x%X] = "
"0x%X", i2c_addr, reg, buf->byte[0], (reg + 1),
buf->byte[1]);
ret = i2c_burst_write(i2c_master, i2c_addr, reg, buf->byte, 2);
if (ret) {
DBG("PCAL9535A[0x%X]: error writing from register 0x%X (%d)\n",
i2c_addr, reg, ret);
SYS_LOG_ERR("PCAL9535A[0x%X]: error writing from register 0x%X "
"(%d)", i2c_addr, reg, ret);
}
return ret;
@ -368,7 +360,7 @@ static int gpio_pcal9535a_config(struct device *dev, int access_op,
{
int ret;
#ifdef CONFIG_GPIO_PCAL9535A_DEBUG
#if (CONFIG_SYS_LOG_GPIO_PCAL9535A_LEVEL >= SYS_LOG_LEVEL_DEBUG)
const struct gpio_pcal9535a_config * const config =
dev->config->config_info;
uint16_t i2c_addr = config->i2c_slave_addr;
@ -380,22 +372,22 @@ static int gpio_pcal9535a_config(struct device *dev, int access_op,
ret = _setup_pin_dir(dev, access_op, pin, flags);
if (ret) {
DBG("PCAL9535A[0x%X]: error setting pin direction (%d)\n",
i2c_addr, ret);
SYS_LOG_ERR("PCAL9535A[0x%X]: error setting pin direction (%d)",
i2c_addr, ret);
goto done;
}
ret = _setup_pin_polarity(dev, access_op, pin, flags);
if (ret) {
DBG("PCAL9535A[0x%X]: error setting pin polarity (%d)\n",
i2c_addr, ret);
SYS_LOG_ERR("PCAL9535A[0x%X]: error setting pin polarity (%d)",
i2c_addr, ret);
goto done;
}
ret = _setup_pin_pullupdown(dev, access_op, pin, flags);
if (ret) {
DBG("PCAL9535A[0x%X]: error setting pin pull up/down (%d)\n",
i2c_addr, ret);
SYS_LOG_ERR("PCAL9535A[0x%X]: error setting pin pull up/down "
"(%d)", i2c_addr, ret);
goto done;
}