boards: arm: gd32a503v_eval: introduce gd32a503v_eval board

introduce gd32a503v_eval board

Signed-off-by: YuLong Yao <feilongphone@gmail.com>

boards/arm/gd32a503v_eval/Kconfig.board

@@ -0,0 +1,6 @@
+# Copyright (c) 2022 YuLong Yao <feilongphone@gmail.com>
+# SPDX-License-Identifier: Apache-2.0
+
+config BOARD_GD32A503V_EVAL
+	bool "GigaDevice GD32A503V-EVAL"
+	depends on SOC_GD32A503

boards/arm/gd32a503v_eval/Kconfig.defconfig

@@ -0,0 +1,9 @@
+# Copyright (c) 2022 YuLong Yao <feilongphone@gmail.com>
+# SPDX-License-Identifier: Apache-2.0
+
+if BOARD_GD32A503V_EVAL
+
+config BOARD
+	default "gd32a503v_eval"
+
+endif # BOARD_GD32A503V_EVAL

boards/arm/gd32a503v_eval/board.cmake

@@ -0,0 +1,8 @@
+# Copyright (c) 2022 YuLong Yao <feilongphone@gmail.com>
+# SPDX-License-Identifier: Apache-2.0
+
+board_runner_args(pyocd "--target=gd32a503vd" "--tool-opt=--pack=${ZEPHYR_HAL_GIGADEVICE_MODULE_DIR}/${CONFIG_SOC_SERIES}/support/GigaDevice.GD32A50x_DFP.1.0.0.pack")
+include(${ZEPHYR_BASE}/boards/common/pyocd.board.cmake)
+
+board_runner_args(gd32isp "--device=GD32A503VDT3")
+include(${ZEPHYR_BASE}/boards/common/gd32isp.board.cmake)

boards/arm/gd32a503v_eval/doc/index.rst

@@ -0,0 +1,223 @@
+.. _gd32a503v_eval:
+
+GigaDevice GD32A503V-EVAL
+#########################
+
+
+Overview
+********
+
+The GD32A503V-EVAL board is a hardware platform that enables design and debug
+of the GigaDevice A503 Cortex-M4F High Performance MCU.
+
+The GD32A503VD features a single-core ARM Cortex-M4F MCU which can run up
+to 120-MHz with flash accesses zero wait states, 384kiB of Flash, 48kiB of
+SRAM and 88 GPIOs.
+
+.. image:: img/gd32a503v_eval.jpg
+     :align: center
+     :alt: gd32a503v_eval
+
+
+Hardware
+********
+
+- 2 user LEDs
+- 2 user push buttons
+- Reset Button
+- ADC connected to a potentiometer
+- 1 DAC channels
+- GD25Q16 2Mib SPI Flash
+- AT24C02C 2KiB EEPROM
+- CS4344 Stereo DAC with Headphone Amplifier
+- GD-Link interface
+
+  - CMSIS-DAP swd debug interface over USB HID.
+
+- 2 CAN port(support CAN-FD)
+
+For more information about the GD32A503 SoC and GD32A503V-EVAL board:
+
+- `GigaDevice Cortex-M33 High Performance SoC Website`_
+- `GD32A503 Datasheet`_
+- `GD32A503 Reference Manual`_
+- `GD32A503V Eval Schematics`_
+- `GD32 ISP Console`_
+
+
+Supported Features
+==================
+
+The board configuration supports the following hardware features:
+
+.. list-table::
+   :header-rows: 1
+
+   * - Peripheral
+     - Kconfig option
+     - Devicetree compatible
+   * - EXTI
+     - :kconfig:option:`CONFIG_GD32_EXTI`
+     - :dtcompatible:`gd,gd32-exti`
+   * - GPIO
+     - :kconfig:option:`CONFIG_GPIO`
+     - :dtcompatible:`gd,gd32-gpio`
+   * - NVIC
+     - N/A
+     - :dtcompatible:`arm,v8m-nvic`
+   * - PWM
+     - :kconfig:option:`CONFIG_PWM`
+     - :dtcompatible:`gd,gd32-pwm`
+   * - SYSTICK
+     - N/A
+     - N/A
+   * - USART
+     - :kconfig:option:`CONFIG_SERIAL`
+     - :dtcompatible:`gd,gd32-usart`
+   * - PINMUX
+     - :kconfig:option:`CONFIG_PINCTRL`
+     - :dtcompatible:`gd,gd32-pinctrl-af`
+   * - ADC
+     - :kconfig:option:`CONFIG_ADC`
+     - :dtcompatible:`gd,gd32-adc`
+   * - DAC
+     - :kconfig:option:`CONFIG_DAC`
+     - :dtcompatible:`gd,gd32-dac`
+   * - FMC
+     - N/A
+     - :dtcompatible:`gd,gd32-flash-controller`
+   * - SPI
+     - :kconfig:option:`CONFIG_SPI`
+     - :dtcompatible:`gd,gd32-spi`
+
+Serial Port
+===========
+
+The GD32A503V-EVAL board has 3 serial communication ports. The default port
+is UART0 at PIN-72 and PIN-73.
+
+Programming and Debugging
+*************************
+
+Before program your board make sure to configure boot setting and serial port.
+The default serial port is USART0.
+
++--------+--------+------------+
+| Boot-0 | Boot-1 | Function   |
++========+========+============+
+|  1-2   |  1-2   | SRAM       |
++--------+--------+------------+
+|  1-2   |  2-3   | Bootloader |
++--------+--------+------------+
+|  2-3   |  Any   | Flash      |
++--------+--------+------------+
+
+Using GD-Link
+=============
+
+The GD32A503V-EVAL includes an onboard programmer/debugger (GD-Link) which
+allow flash programming and debug over USB. There are also program and debug
+headers J2 and J100 that can be used with any ARM compatible tools.
+
+#. Build the Zephyr kernel and the :ref:`hello_world` sample application:
+
+   .. zephyr-app-commands::
+      :zephyr-app: samples/hello_world
+      :board: gd32a503v_eval
+      :goals: build
+      :compact:
+
+#. Run your favorite terminal program to listen for output. Under Linux the
+   terminal should be :code:`/dev/ttyUSB0`. For example:
+
+   .. code-block:: console
+
+      $ minicom -D /dev/ttyUSB0 -o
+
+   The -o option tells minicom not to send the modem initialization
+   string. Connection should be configured as follows:
+
+      - Speed: 115200
+      - Data: 8 bits
+      - Parity: None
+      - Stop bits: 1
+
+#. To flash an image:
+
+   .. zephyr-app-commands::
+      :zephyr-app: samples/hello_world
+      :board: gd32a503v_eval
+      :goals: flash
+      :compact:
+
+   You should see "Hello World! gd32a503v_eval" in your terminal.
+
+#. To debug an image:
+
+   .. zephyr-app-commands::
+      :zephyr-app: samples/hello_world
+      :board: gd32a503v_eval
+      :goals: debug
+      :compact:
+
+
+Using ROM bootloader
+====================
+
+The GD32A503 MCU have a ROM bootloader which allow flash programming.  User
+should install `GD32 ISP Console`_ software at some Linux path.  The recommended
+is :code:`$HOME/.local/bin`.
+
+#. Build the Zephyr kernel and the :ref:`hello_world` sample application:
+
+   .. zephyr-app-commands::
+      :zephyr-app: samples/hello_world
+      :board: gd32a503v_eval
+      :goals: build
+      :compact:
+
+#. Enable board bootloader:
+
+   - Remove boot-0 jumper
+   - press reset button
+
+#. To flash an image:
+
+   .. code-block:: console
+
+      west flash -r gd32isp [--port=/dev/ttyUSB0]
+
+#. Run your favorite terminal program to listen for output. Under Linux the
+   terminal should be :code:`/dev/ttyUSB0`. For example:
+
+   .. code-block:: console
+
+      $ minicom -D /dev/ttyUSB0 -o
+
+   The -o option tells minicom not to send the modem initialization
+   string. Connection should be configured as follows:
+
+      - Speed: 115200
+      - Data: 8 bits
+      - Parity: None
+      - Stop bits: 1
+
+   Press reset button
+
+   You should see "Hello World! gd32a503v_eval" in your terminal.
+
+
+.. _GigaDevice Cortex-M33 High Performance SoC Website:
+	https://www.gigadevice.com.cn/product/mcu/arm-cortex-m33/gd32a503vdt3
+
+.. _GD32A503 Datasheet:
+	https://www.gd32mcu.com/download/down/document_id/401/path_type/1
+
+.. _GD32A503 Reference Manual:
+	https://www.gd32mcu.com/download/down/document_id/402/path_type/1
+
+.. _GD32A503V Eval Schematics:
+	https://www.gd32mcu.com/download/down/document_id/404/path_type/1
+
+.. _GD32 ISP Console:
+	http://www.gd32mcu.com/download/down/document_id/175/path_type/1

boards/arm/gd32a503v_eval/gd32a503v_eval-pinctrl.dtsi

@@ -0,0 +1,35 @@
+/*
+ * Copyright (c) 2022 YuLong Yao <feilongphone@gmail.com>
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+#include <dt-bindings/pinctrl/gd32a503v(b-c-d)xx-pinctrl.h>
+
+&pinctrl {
+	usart0_default: usart0_default {
+		group1 {
+			pinmux = <USART0_TX_PA10>, <USART0_RX_PA11>;
+		};
+	};
+
+	adc0_default: adc0_default {
+		group1 {
+			pinmux = <ADC0_IN1_PC10>;
+		};
+	};
+
+	dac_default: dac_default {
+		group1 {
+			pinmux = <DAC_OUT_PA7>;
+		};
+	};
+
+	spi0_default: spi0_default {
+		group1 {
+			pinmux = <SPI0_SCK_PE14>, <SPI0_MOSI_PA2>,
+				 <SPI0_MISO_PE13>,
+				 /* Use pinmux to pullup pg10 and pg11. */
+				 <SPI0_IO2_PE15>, <SPI0_IO3_PB10>;
+		};
+	};
+};

boards/arm/gd32a503v_eval/gd32a503v_eval.dts

@@ -0,0 +1,103 @@
+/*
+ * Copyright (c) 2022 YuLong Yao <feilongphone@gmail.com>
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/dts-v1/;
+
+#include <gigadevice/gd32a50x/gd32a503vdt3.dtsi>
+#include "gd32a503v_eval-pinctrl.dtsi"
+
+/ {
+	model = "GigaDevice GD32A503V-EVAL";
+	compatible = "gd,gd32a503v-eval";
+
+	chosen {
+		zephyr,sram = &sram0;
+		zephyr,flash = &flash0;
+		zephyr,console = &usart0;
+		zephyr,shell-uart = &usart0;
+		zephyr,flash-controller = &fmc;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led1: led1 {
+			gpios = <&gpioc 0 GPIO_ACTIVE_LOW>;
+			label = "LED1";
+		};
+		led2: led2 {
+			gpios = <&gpioc 1 GPIO_ACTIVE_LOW>;
+			label = "LED2";
+		};
+	};
+
+	aliases {
+		led0 = &led1;
+		led1 = &led2;
+		spi-flash0 = &nor_flash;
+	};
+};
+
+&gpioa {
+	status = "okay";
+};
+
+&gpiob {
+	status = "okay";
+};
+
+&gpioc {
+	status = "okay";
+};
+
+&gpiod {
+	status = "okay";
+};
+
+&gpioe {
+	status = "okay";
+};
+
+&gpiof {
+	status = "okay";
+};
+
+&usart0 {
+	status = "okay";
+	current-speed = <115200>;
+	pinctrl-0 = <&usart0_default>;
+	pinctrl-names = "default";
+};
+
+&adc0 {
+	status = "okay";
+	pinctrl-0 = <&adc0_default>;
+	pinctrl-names = "default";
+};
+
+&dac {
+	status = "okay";
+	pinctrl-0 = <&dac_default>;
+	pinctrl-names = "default";
+};
+
+&fwdgt {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+	pinctrl-0 = <&spi0_default>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpioa 1 GPIO_ACTIVE_LOW>;
+
+	nor_flash: gd25q16@0 {
+		compatible ="jedec,spi-nor";
+		size = <0x1000000>;
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		status = "okay";
+		jedec-id = [c8 40 15];
+	};
+};

boards/arm/gd32a503v_eval/gd32a503v_eval_defconfig

@@ -0,0 +1,13 @@
+# Copyright (c) 2022 YuLong Yao <feilongphone@gmail.com>
+# SPDX-License-Identifier: Apache-2.0
+
+CONFIG_SOC_SERIES_GD32A50X=y
+CONFIG_SOC_GD32A503=y
+CONFIG_BOARD_GD32A503V_EVAL=y
+
+CONFIG_ARM_MPU=y
+CONFIG_HW_STACK_PROTECTION=y
+
+CONFIG_CONSOLE=y
+CONFIG_UART_CONSOLE=y
+CONFIG_SERIAL=y

boards/arm/gd32a503v_eval/gd32f450z_eval.yaml

@@ -0,0 +1,23 @@
+# Copyright (c) 2022 YuLong Yao <feilongphone@gmail.com>
+# SPDX-License-Identifier: Apache-2.0
+
+identifier: gd32a503v_eval
+name: GigaDevice GD32A503V-EVAL
+type: mcu
+arch: arm
+ram: 48
+flash: 384
+toolchain:
+  - zephyr
+  - gnuarmemb
+  - xtools
+supported:
+  - adc
+  - counter
+  - dac
+  - dma
+  - gpio
+  - pwm
+  - spi
+  - uart
+  - watchdog