bluetooth: mesh: fix typo

Utilize a code spell-checking tool to scan for and correct spelling errors
in all files within the subsys/bluetooth/mesh directory.

Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>

subsys/bluetooth/mesh/Kconfig

@@ -628,7 +628,7 @@ config BT_MESH_SAR_RX_SEG_INT_STEP
 	help
 	  This value defines the segments reception interval step used for
 	  delaying the transmission of an acknowledgment message after
-	  receiving a new segmnet. The interval is measured in milliseconds
+	  receiving a new segment. The interval is measured in milliseconds
 	  and calculated using the following formula:
 	  (CONFIG_BT_MESH_SAR_RX_SEG_INT_STEP + 1) * 10 ms
 
@@ -679,7 +679,7 @@ config BT_MESH_RPL_STORAGE_MODE_SETTINGS
 	bool "Persistent storage of RPL in Settings"
 	help
 	  Persistent storage of RPL in Settings. If BT_SETTINGS is not
-	  enabled this choise will provide a non-persistent implementation
+	  enabled this choice will provide a non-persistent implementation
 	  variant of the RPL list.
 
 endchoice

subsys/bluetooth/mesh/blob_cli.c

@@ -764,9 +764,9 @@ static void block_get_tx(struct bt_mesh_blob_cli *cli, uint16_t dst)
  *
  * After sending all reported missing chunks to each target, the Client updates
  * @ref bt_mesh_blob_target_pull::block_report_timestamp value for every target individually in
- * chunk_tx_complete. The Client then proceedes to block_report_wait state and uses the earliest of
+ * chunk_tx_complete. The Client then proceeds to block_report_wait state and uses the earliest of
  * all block_report_timestamp and cli_timestamp to schedule the retry timer. When the retry
- * timer expires, the Client proceedes to the block_check_end state.
+ * timer expires, the Client proceeds to the block_check_end state.
  *
  * In Pull mode, target nodes send a Partial Block Report message to the Client to inform about
  * missing chunks. The Client doesn't control when these messages are sent by target nodes, and
@@ -916,7 +916,7 @@ static void chunk_tx_complete(struct bt_mesh_blob_cli *cli, uint16_t dst)
 	int64_t timestamp = k_uptime_get() + BLOCK_REPORT_TIME_MSEC;
 
 	if (!UNICAST_MODE(cli)) {
-		/* If using group adressing, reset timestamp for all targets after all chunks are
+		/* If using group addressing, reset timestamp for all targets after all chunks are
 		 * sent to the group address
 		 */
 		TARGETS_FOR_EACH(cli, target) {

subsys/bluetooth/mesh/op_agg_srv.c

@@ -19,7 +19,7 @@ LOG_MODULE_REGISTER(bt_mesh_op_agg_srv);
 
 NET_BUF_SIMPLE_DEFINE_STATIC(sdu, BT_MESH_TX_SDU_MAX);
 
-/** Mesh Opcodes Aggragator Server Model Context */
+/** Mesh Opcodes Aggregator Server Model Context */
 static struct bt_mesh_op_agg_srv {
 	/** Composition data model entry pointer. */
 	const struct bt_mesh_model *model;

subsys/bluetooth/mesh/provisionee.c

@@ -195,7 +195,7 @@ static void prov_start(const uint8_t *data)
 		       bt_mesh_prov->static_val_len > auth_size ? auth_size
 								: bt_mesh_prov->static_val_len);
 
-		/* Padd with zeros if the Auth is shorter the required length*/
+		/* Pad with zeros if the Auth is shorter the required length */
 		if (bt_mesh_prov->static_val_len < auth_size) {
 			memset(bt_mesh_prov_link.auth + bt_mesh_prov->static_val_len, 0,
 			       auth_size - bt_mesh_prov->static_val_len);

subsys/bluetooth/mesh/provisioner.c

@@ -767,7 +767,7 @@ int bt_mesh_auth_method_set_static(const uint8_t *static_val, uint8_t size)
 	memcpy(bt_mesh_prov_link.auth, static_val,
 	       size > PROV_AUTH_MAX_LEN ? PROV_AUTH_MAX_LEN : size);
 
-	/* Padd with zeros if the Auth is shorter the required length*/
+	/* Pad with zeros if the Auth is shorter the required length */
 	if (size < PROV_AUTH_MAX_LEN) {
 		memset(bt_mesh_prov_link.auth + size, 0, PROV_AUTH_MAX_LEN - size);
 	}

subsys/bluetooth/mesh/sar_cfg_internal.h

@@ -11,9 +11,9 @@
 #ifndef ZEPHYR_SUBSYS_BLUETOOTH_MESH_SAR_CFG_INTERNAL_H__
 #define ZEPHYR_SUBSYS_BLUETOOTH_MESH_SAR_CFG_INTERNAL_H__
 
-/** SAR Transmitter Configuraion state encoded length */
+/** SAR Transmitter state encoded length */
 #define BT_MESH_SAR_TX_LEN 4
-/** SAR Receiver Configuraion state encoded length */
+/** SAR Receiver state encoded length */
 #define BT_MESH_SAR_RX_LEN 3
 
 /** SAR Transmitter Configuration state initializer */

subsys/bluetooth/mesh/shell/cfg.c

@@ -1150,7 +1150,7 @@ static int cmd_mod_sub_del(const struct shell *sh, size_t argc, char *argv[])
 	if (status) {
 		shell_print(sh, "Model Subscription Delete failed with status 0x%02x", status);
 	} else {
-		shell_print(sh, "Model subscription deltion was successful");
+		shell_print(sh, "Model subscription deletion was successful");
 	}
 
 	return 0;
@@ -1387,7 +1387,7 @@ static int cmd_mod_sub_del_all(const struct shell *sh, size_t argc, char *argv[]
 	if (status) {
 		shell_print(sh, "Model Subscription Delete All failed with status 0x%02x", status);
 	} else {
-		shell_print(sh, "Model subscription deltion all was successful");
+		shell_print(sh, "Model subscription deletion all was successful");
 	}
 
 	return 0;

subsys/bluetooth/mesh/va.h

@@ -42,7 +42,7 @@ uint8_t bt_mesh_va_del(const uint8_t *uuid);
  */
 const struct bt_mesh_va *bt_mesh_va_find(const uint8_t *uuid);
 
-/** @brief Check if there are more than one Label UUID which hash has the specificed virtual
+/** @brief Check if there are more than one Label UUID which hash has the specified virtual
  * address.
  *
  * @param addr Virtual address to check