michaelh/zephyr
1
0
Fork 0
Code Releases Activity
zephyr/drivers/pinmux/Kconfig.esp32

11 lines
246 B
Plaintext
Raw Permalink Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 13:45:29 +01:00
# ESP32 Pin mux configuration options
drivers: pinmux: Add pin multiplexer driver for ESP32 This implements a driver for the pin multiplexer as present in the ESP32 SoCs. All APIs are supported. Jira: ZEP-2297 Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
2017-06-27 02:07:43 +02:00
# Copyright (c) 2017 Intel Corporation
# SPDX-License-Identifier: Apache-2.0
kconfig: Turn pointless/confusing 'menuconfig's into 'config's Defining a symbol with 'menuconfig' just tells the menuconfig to display any dependent symbols that immediately follow it in a separate menu. 'menuconfig' has no effect on symbol values. Making a symbol that doesn't have any dependent symbols after it a 'menuconfig' should be avoided, because then you end up with an empty menu, which is shown as e.g. [*] Enable foo --- This is how it would be shown if there were children but they all happened to be invisible as well. With a regular 'config', it turns into [*] Enable foo Change all pointless 'menuconfig's to 'config's. See the section on 'menuconfig' on the Kconfig - Tips and Best Practices page as well. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-10-22 01:04:04 +02:00
config PINMUX_ESP32
drivers: pinmux: Add pin multiplexer driver for ESP32 This implements a driver for the pin multiplexer as present in the ESP32 SoCs. All APIs are supported. Jira: ZEP-2297 Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
2017-06-27 02:07:43 +02:00
bool "ESP32 Pin multiplexer driver"
kconfig: pinmux: Remove lots of redundant PINMUX dependencies Most of these are from source'ing a file within an 'if PINMUX', and then adding another 'depends on PINMUX' within it. 'if FOO' is just shorthand for adding 'depends on FOO' to each item within the 'if'. There are no "conditional includes" in Kconfig, so 'if FOO' has no special meaning around a 'source'. Conditional includes wouldn't be possible, because an 'if' condition could include (directly or indirectly) forward references to symbols not defined yet. Tip: When adding a symbol, check its dependencies in the menuconfig ('ninja menuconfig', then / to jump to the symbol). The menuconfig also shows how the file with the symbol got included, so if you see duplicated dependencies, it's easy to hunt down where they come from. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-03-07 05:54:37 +01:00
depends on SOC_ESP32
drivers: pinmux: Add pin multiplexer driver for ESP32 This implements a driver for the pin multiplexer as present in the ESP32 SoCs. All APIs are supported. Jira: ZEP-2297 Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
2017-06-27 02:07:43 +02:00
help
kconfig: fix more help spacing issues Fix Kconfig help sections and add spacing to be consistent across all Kconfig file. In a previous run we missed a few. Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2018-02-15 14:36:16 +01:00
Enable driver for ESP32 Pin multiplexer.
Copy permalink