michaelh/zephyr
1
0
Fork 0
Code Releases Activity
zephyr/boards/arm/stm32f723e_disco/Kconfig.defconfig

17 lines
275 B
Plaintext
Raw Permalink Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 13:45:29 +01:00
# STM32F723E DISCOVERY board configuration
boards: arm: stm32: basic support for STM32F723E-DISCO board This patch adds basic support and documentation for the STM32F723E-DISCO board, with GPIO, USART, I2C and USB support. Two USARTs are enabled, the VCP one for the console and the Arduino one. The GPIOs are configured for the 3 LEDs and the button available on the board. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2018-06-28 21:52:42 +02:00
kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 13:45:29 +01:00
# Copyright (c) 2018 Aurelien Jarno
boards: arm: stm32: basic support for STM32F723E-DISCO board This patch adds basic support and documentation for the STM32F723E-DISCO board, with GPIO, USART, I2C and USB support. Two USARTs are enabled, the VCP one for the console and the Arduino one. The GPIOs are configured for the 3 LEDs and the button available on the board. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2018-06-28 21:52:42 +02:00
# SPDX-License-Identifier: Apache-2.0
if BOARD_STM32F723E_DISCO
config BOARD
default "stm32f723e_disco"
boards: stm32f723e_disco: Conform to default configuration guidelines Update stm32f723e_disco configuration to match with default configuration guidelines: -Configure available connectors Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2018-09-14 15:11:12 +02:00
config SPI_STM32_INTERRUPT
default y
boards: stm32: Use dt API for peripheral configuration Replace use of Kconfig SPI_X symbols by calls to DT API. Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2020-04-16 20:52:22 +02:00
depends on SPI
boards: stm32f723e_disco: Conform to default configuration guidelines Update stm32f723e_disco configuration to match with default configuration guidelines: -Configure available connectors Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2018-09-14 15:11:12 +02:00
boards: arm: stm32f723e_disco: enable I2C support Enable the support for the 3 I2C buses of the STM32F723E-DISCO board, connected respectively to the WM8994, the Arduino V3/STMOD+ and the touch panel. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2018-07-03 22:03:34 +02:00
boards: arm: stm32: basic support for STM32F723E-DISCO board This patch adds basic support and documentation for the STM32F723E-DISCO board, with GPIO, USART, I2C and USB support. Two USARTs are enabled, the VCP one for the console and the Arduino one. The GPIOs are configured for the 3 LEDs and the button available on the board. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2018-06-28 21:52:42 +02:00
endif # BOARD_STM32F723E_DISCO
Copy permalink