michaelh/zephyr
1
0
Fork 0
Code Releases Activity
zephyr/tests/bluetooth/tester/nrf5340_hci_ipc_cpunet.conf

9 lines
285 B
Plaintext
Raw Permalink Normal View History

bluetooth: Rename rpmsg HCI driver and sample to ipc The existing driver and sample: - drivers/bluetooth/hci/rpmsg - samples/bluetooth/hci_rpmsg are no longer correctly named, since they now use the IPC subsystem to send and receive data. The IPC subsystem can use RPMsg as a transport, but that is one of several selectable backends. I initially wanted to deprecated both the BT_RPMSG Kconfig option as well as the zephyr,bt-hci-rpmsg-ipc chosen node in Devicetree. However, this proved to be undoable in the case of the Kconfig option. This is because it's a choice option, and those have special behavior. In particular, the only practical way to deprecate would've been to keep the old Kconfig option outside the choice (much like it's done in this commit) but then also add a 'depends on !BT_RPMSG' on each of the remaining choice symbols *except* on the new BT_HCI_IPC one. This, however, only works correctly for .conf files. If a board instead sets the default BT_HCI_BUS_TYPE in the Kconfig.defconfig file then the Kconfig tree parsing would fail, because it'd try to set it to a value (BT_RPMSG) that is no longer part of the choice. Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
2023-08-28 21:04:28 +02:00
# Apply this overlay at hci_ipc controller build
tests: bluetooth: tester: Reduce nrf53 BT_BUF_ACL_RX_SIZE PTS l2cap tests need BT_BUF_ACL_RX_SIZE to be 100. Signed-off-by: Lang Xie <Lang.Xie@nordicsemi.no> Signed-off-by: Magdalena Kasenberg <magdalena.kasenberg@codecoup.pl>
2023-05-26 17:02:48 +02:00
CONFIG_BT_CTLR_CONN_ISO_LOW_LATENCY_POLICY=y
CONFIG_BT_CTLR_DATA_LENGTH_MAX=100
CONFIG_BT_BUF_ACL_RX_SIZE=100
bluetooth: tester: bap: Add support for BAP/USR tests Extend Codec capabilities of the server. At Codec Config operation initiated autonomously by server, all ASEs with lower IDs than the requested one have to be initated first due to API limitation. In some BAP/USR (server role) test cases the PTS sends the MMI 202 to configure the Sink ASE to streaming state, in some others it does not. For now, let's autonomously send Receiver Start Ready at ASE Enabled. Signed-off-by: Magdalena Kasenberg <magdalena.kasenberg@codecoup.pl>
2023-07-18 15:13:51 +02:00
CONFIG_BT_CTLR_PERIPHERAL_ISO_EARLY_CIG_START=y
bluetooth: tester: Enable BT_CTLR_ISOAL_PSN_IGNORE Temporarily ignore the Tx ISO Data Packet Sequence Number use as the tester app does not have yet a synchronization mechanism for the sequence number and it constantly fails to send ISO data on time. Signed-off-by: Magdalena Kasenberg <magdalena.kasenberg@codecoup.pl>
2024-01-24 14:51:35 +01:00
CONFIG_BT_CTLR_ISOAL_PSN_IGNORE=y
bluetooth: tester: CSIP tests Adding support for CSIP client role tests. Signed-off-by: Piotr Narajowski <piotr.narajowski@codecoup.pl>
2024-02-06 11:05:08 +01:00
CONFIG_BT_MAX_CONN=3
bluetooth: tester: add missing config Set CONFIG_BT_MAX_PAIRED with same value as in host. This is needed for CSIP tests with three lower testers: CSIP/CL/SP/BV-07-C, CSIP/CL/SP/BV-03-C, CSIP/CL/SP/BV-04-C, CSIP/CL/SPE/BI-01-C Signed-off-by: Piotr Narajowski <piotr.narajowski@codecoup.pl>
2024-03-28 16:19:42 +01:00
CONFIG_BT_MAX_PAIRED=3
Copy permalink