DTF UHF
ac94147589
Have servos output midrc at startup instead of 1ms pulse (full deflection)
2014-02-14 15:15:38 -05:00
dongie
4e44cf62a2
Merge pull request #43 from kh4/master
...
Fix line endings to CRLF
2014-02-07 21:12:12 +09:00
kh4
ceb1f78526
Fix line endings to CRLF
2014-02-07 13:40:27 +02:00
dongie
0c46bdbfc8
added cli settings for pidvel
...
added (unsupported) GPS nav MSP numbers.
2014-02-04 08:21:40 +09:00
dongie
efedff771e
adding updated uvision project
2014-01-31 21:51:10 +09:00
dongie
e8b3d00003
implement (not flight tested) brushed motors support.
...
set motor_pwm_rate to some value > 500 (1000, 8000, 16000 etc works on my scope).
then the motor output can be used to directly drive brushed motor fets.
PWM is rescaled to 0-base in brushed mode, so all same values of min/maxthrottle apply.
2014-01-31 11:56:55 +09:00
dongie
a695ddd66a
added sumd serial receiver support by cesco/Plüschi
2014-01-31 10:02:50 +09:00
dongie
92c0947d7f
bump config version after PID default changes and add built hex file
2014-01-28 10:03:30 +09:00
dongie
e787a493dd
Merge pull request #42 from luggi/betteralthold
...
new althold PID
2014-01-27 16:34:13 -08:00
Lukas S
073f5116bb
new althold PID
...
althold should work better now, the PID settings are preliminary. There
is definetly room for improvement.
For aquiring your own PID settings set ALT_P = 0 and tune the VEL pid
until the copter only drifts a little from its position when you
activate althold. Then set ALT_P to a value where it holds the position
stable
2014-01-28 01:26:58 +01:00
dongie
cae8682c62
Merge pull request #41 from schugabe/master
...
modified MSP implementation to reflect MW2.3 changes
2014-01-27 05:38:39 -08:00
Johannes Kasberger
142bb20ae6
modified MSP implementation to reflect MW2.3 changes
2014-01-27 14:27:43 +01:00
dongie
e4746e60cf
hex to match latest source commits
2014-01-26 09:32:12 +09:00
Dominic Clifton
398fcffd1a
Merge remote-tracking branch 'multiwii/master'
2014-01-24 18:45:38 +00:00
dongie
cc2a6f502e
Merge pull request #38 from DTFUHF/master
...
Enable gimbal_flags servo passthrough in airplane mode and other mixer modes that use servos
2014-01-23 15:41:12 -08:00
DTF UHF
1cb905b7c2
fix spacing
2014-01-23 17:52:04 -05:00
DTF UHF
d0a5a66b62
Enable gimbal_flags servo passthru in airplane modes and other mixer modes that use servos
2014-01-23 17:48:27 -05:00
dongie
a2c9ea3e8b
Merge pull request #34 from KipK/Telemetry_switch
...
Telemetry switch
2014-01-17 14:57:13 -08:00
KipK
6ee98fed90
indents
2014-01-17 17:02:48 +01:00
KipK
e198f1727b
telemetry_switch: fixed condition when using softserial
2014-01-17 11:07:59 +01:00
KipK
7bd2db04be
Added a mcfg.telemetry_switch for CLI
...
If telemetry_switch=1 it change baudrate and protocol using aux channel, either it switch when armed/disarmed.
This allows to keep MSP serial while armed for BT dongle if needed.
2014-01-16 19:36:54 +01:00
KipK
0d974e2882
reverting previous fix. This doesn't solve all conditions.
...
I need to add a telemetry_switch conf or feature to solve enabling MSP over FRSKy with switch not activated when armed ( i.e. using bt serial for tuning sessions ), but it will break when not using telemetry switch.
Better to keep it like this for now.
2014-01-16 17:18:43 +01:00
dongie
c19f6d1355
Merge pull request #33 from KipK/Telemetry_switch
...
Telemetry switch: fix stupid mistake
2014-01-16 07:45:14 -08:00
KipK
b55496b13f
Telemetry switch: fix stupid mistake
2014-01-16 16:18:36 +01:00
dongie
94d1e19403
Merge pull request #32 from KipK/Telemetry_switch
...
Start Frsky telemetry using a switch without beeing armed.
2014-01-15 05:54:58 -08:00
KipK
e6889aea12
Start Frsky telemetry using a switch without beeing armed.
...
This adds a Telemetry checkbox in the gui.
2014-01-15 14:53:03 +01:00
dongie
8c4a594808
build for throttle angle correction
2014-01-15 22:06:31 +09:00
dongie
699dc00332
Merge branch 'fix' of https://github.com/treymarc/baseflight into treymarc-fix
2014-01-15 22:04:19 +09:00
dongie
a206965854
adding support for maxthrottle and mincommand in MSP_SET_MISC now that all the tools can use it.
2014-01-15 19:37:31 +09:00
dongie
9a7ff04422
adding untested (and needing work) fixedwing althold implementation.
...
see comments in code for things to fix. added new variable to cli, fixedwing_althold_dir (though its value isn't really clear, I think it should always be positive since servo direction mix is done later).
2014-01-06 21:38:36 +09:00
treymarc
b2e7c8d8fc
THROTTLE ANGLE CORRECTION , "*" "/" operator priority bug
...
http://www.multiwii.com/forum/viewtopic.php?f=8&t=4433
2014-01-04 22:19:51 +01:00
dongie
1dea496fd5
build for mixer update
2014-01-01 19:44:33 +09:00
dongie
edd2d4921b
Merge pull request #28 from treymarc/temp
...
correction for mixerHex6P and mixerHex6X
2014-01-01 02:41:56 -08:00
dongie
f29405ffb0
whitespace fixes in Makefile
2014-01-01 19:19:10 +09:00
treymarc
bf5b70f4e2
remove newlib stub , add mixer correction
2014-01-01 10:23:48 +01:00
treymarc
01f079c254
ed
2014-01-01 10:18:18 +01:00
treymarc
239120ba4e
ignore white space
2014-01-01 10:14:23 +01:00
treymarc
2caa1fbb20
add newlib stubs
2014-01-01 09:42:14 +01:00
treymarc
d885e39a90
type float
2014-01-01 09:24:12 +01:00
treymarc
c76a9669f6
mixer coorection for hexa6x and hexa6p
2014-01-01 09:17:13 +01:00
treymarc
033a8fbe3f
ident/format
2014-01-01 09:16:41 +01:00
dongie
13324c9f88
build binary for the previous GPS baud rate index fix
2013-12-27 08:37:17 +09:00
Kemal Hadimli
b74b9f182b
gps: use gpsData.baudrateIndex all around
2013-12-26 22:17:05 +02:00
dongie
44adda8b3b
gps fix build
2013-12-24 23:46:18 +09:00
dongie
ac3b1fab64
Merge pull request #25 from disq/gps_baudfix
...
GPS Autoconfigure fix
2013-12-24 06:40:18 -08:00
Kemal Hadimli
d9c9cbfb9f
another formatting fix
2013-12-24 16:15:08 +02:00
Kemal Hadimli
ab49f4efd2
fix formatting
2013-12-24 02:20:17 +02:00
Kemal Hadimli
11abec88ed
gps nmea: reset error counter on init hardware
2013-12-24 01:48:51 +02:00
Kemal Hadimli
51b8a9e365
gps autoconfigure: wait 100ms between baud changes
2013-12-24 01:48:47 +02:00
Dominic Clifton
c525213355
Whitespace cleanup
2013-12-15 16:35:45 +00:00
