feature TELEMETRY to enable it. when armed, telemetry is sent out the TX pin. It must be connected to 'Rx' pin of FrSky telemetry receiver via a level shifter. When disarmed, port goes back to 115200 bps for GUI.
fixed a typo in imu.c introduced by GYRO_INTERLEAVE junk.
todo: just switch serial speed instead of reinitializing everything.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@173 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
changed booleans to bitfield struct to match with 0622
no other functional changes, and not all enhancements (like boxlight) from 0622 are implemented yet
NOT flight tested, use at your own risk.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@172 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
put gyro interleave under define. this needs to be cleaned sometime.
took out "gyro glitch" stuff that was leftover from nintendo days.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@162 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
applied mwc-dev GPS code with bits of tarducopter code by sbaron. Thanks again. Moved some of the GPS config stuff into cli - gps_lpf, min/max nav speed, nav_controls_heading. Remember I don't test any GPS functionality at all, so if this makes your quad fly towards North Korea at over 9000cm/sec, this is NOT my problem.
spacing fixes in a couple files.
trashed old serial code that was under #if 0
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@161 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added arm/disarm on left/righ roll while throttle down to configuration options and disabled it by default. "set retarded_arm" in CLI
put gyro_cmpf_factor into settings. default is 310, can be increased to decrease acc influence. debug use only.
dropped acc_lpf_factor back to 4. those who want it at 100, make it so.
cleaned up MPU6050 driver with humanreadable register names
got rid of MMGYRO crap - no use
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@159 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added mag_declination set option to cli - oops
status in cli now prints which ACC hardware is used. work in proress to show difference between hardware with MPU6050 and MPU3050
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@157 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
new config ooptions for failsafe, so current settings are cleared
fixed mistake where yaw servo stuff for tri was still hardcoded even though it had configurable values in cli
reduced level default D to 20 from 100 (dunno what effect this has, shrug)
untested, enable feature FAILSAFE at your own risk.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@155 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
new hex file only works with Java GUI 20120504-dev :( WinGUI is still not updated. Use latest release version on downloads page if want to use WinGUI.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@153 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
fixed spacing in ledring.c
defaulted acc_lpf to 100
correction in vtail4 mix (from multiwii_dev)
trashed more unused LOG_VALUES crap
no binary build since this is untested / non-flight-tested.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@152 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
increased gyro complementary filter factor to 500 to reduce acc influence (should hopefully fix random walk stuff?)
fixed a bug in servotilt stuff (maybe?)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@150 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added fifo mode to adxl345 driver, currently disabled. work in progress.
fixed output for PWM 5-8 when used with PPM + camstab + abovequad configs.
fixed baro, now alt-hold actually works. silly copypaste typo.
trashed all remaining parts of power meter and lcd configuration stuff. useless.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@145 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added float-based acc lpf, acc_lpf_factor values now changed, its 1/factor now, values 60+ and larger filter heavier.
playing with release MPU6050 hardware, looks like acc1G is fucked, as predicted
bug in serial output (forgot to output armed bit to GUI, estalt is /10)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@144 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
increased i2c send buffer to 16bytes (was needed for DMP)
decreased interrupt priority of both uarts - with GPS running at 115200, this would cause I2C errors (i2c interrupt must be highest priority).
GPS was tested with $25 FMP04 GPS module ghettoed up outside my window, locking 5 satellites in a few minutes.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@140 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
whitespace fixes in mw.h and trashed the old XA-XB based mixer setting leftovers.
settings are cleared again due to updated config struct.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@138 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
removed feature digital_servo since its now set by cli instead.
added proper tx end check into uart, to remove delay inside printing out set values and tx buffer overrun during help()
instead of passing a bunch of params to pwm driver, made a config struct
fixed a bug in gps baudrate
fixed typo in stmloader.c
whitespace / indentation cleanups in various drivers
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@137 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
renamed gcc startup file to .S (breaks some lunix dudes apparently)
ppm sum handler waws hardcoded to TIM2 instead of using passed parameter. fixed. (thanks sbaron)
invalid data from pwm/ppm read are returned as midrc, not 1500. (robert_b)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@133 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
split uart2 initialization inside drv_uart. added receive data callback to use either with GPS or spektrum satellite
added spektrum satellite support, also freeing up 4 motor outputs for hexa/octo/camstab
configurable acc lpf and gyro lpf via cli
configurable (build-time) temperature lpf on baro. seems mostly useless.
fixed a nice boner bug in mag code which ended up multiplying magADC twice with magCal data.
fixed mpu3050 driver to allow configurable lpf, also broke other stuff in the process. considering moving this sort of stuff to "init" struct for sensor.
pwm driver rewritten to fully disable pwm/ppm inputs (such as using spektrum satellite case)
cleaned up double math in gps.c to use sinf/cosf etc
removed TRUSTED_ACCZ since its useless anyway
whitespace cleanup
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@130 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
took out leftovers of old dynamic mixer binary protocol - now cli sets it.
added some mpu6050 DMP stuff - all disabled by default, only for testing stuff. ignore it.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@128 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
implemented channel order selection (map in cli). example "map AETR1234" -> ail, ele, throttle, rudder, aux1234. thanks simon for all the halp on this one. truly a mindfuck.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@126 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added (untested) support for additional PWM output channels incase of PPM input - 4 more, so total of 10 outputs in this mode.
added (mostly untested) support for throttle calibration - short out PPM input connector with a bind plug and power up.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@122 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
implemented battery cell count auto detect (DJI, you can steal this source from me for your next product). automatically finds 2S..6S battery, and sets warning voltage accordingly
added new battery config -related stuff in cli, min/max cell voltage for non-lipo users. Defaults for lipo are 4.3V/cell (max) and 3.3V/cell (min).
added pid setting stuff into cli from nicodh
added 'status' command to cli to print out system info.
added build date/time to 'version' in cli, to track down stupid users.
config version bumped, settings are cleared again.
refactored battery voltage stuff a bit, and got rid of 3 levels of warnings. don't see any benefit at all.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@121 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added 'reset to defaults' to cli
got rid of 'servo' feature since that's not really a feature a user can set
added couple more configurable tricopter things to config struct.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@118 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
changed gyro/acc to allow different drivers without recompile, this allowed adding mpu6050 support w/autodetect
moved sensor orientation code into driver - each driver provides its own
added support for mpu6050 - desolder mpu3050 and adxl345, replace with mpu6050 for instant ???
merged multiwii 2.0pre3 code changes (none that mattered except mag calibration and typo in baro stuff)
changes to sensor autodetect for new dynamic drivers
more of ledring stuff done (still doesn't work, so dont try)
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@115 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
